SBJ613 GPM Clutch bell with 5 mmboring for HPI Baja 5, Carson Wild GP Attack, 1 pce.
Product number:
gpm_sbj613
EAN:
4058575029236
Product information "SBJ613 GPM Clutch bell with 5 mmboring for HPI Baja 5, Carson Wild GP Attack, 1 pce."
GPM clutch bell with 5 mm pinion bolt. CNC-machined one-piece bell for absolute true running. Inclusive mountings.
Login
Accessories / Spare parts
Complete set with clutch bell and one each 17T and 18T steel pinion.GPM clutch bell with 5 mm pinion bolt. CNC-machined one-piece bell for absolute true running. Inclusive mountings.GPM 17T and 18T steel pinions are profile regraded. This allows for a change in gearing by a pinion swap alone.Module: m=1,5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Content of delivery:GPM steel clutch bell SBJ613GPM steel pinion 17T SBJ017TGPM steel pinion 18T SBJ018TO
The GPM 16T steel pinion is profile regraded. This allows for a change in gearing by a pinion swap alone. The pinion has the same dimensions as the HPI 17T stock pinion.Module: m=1,5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
The GPM 18T steel pinion is profile regraded. This allows for a change in gearing by a pinion swap alone. The pinion has the same dimensions as the HPI 17T stock pinion.Module: m=1,5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
Regular price: 54,80 EURSteel pinion set with one each 17T and 18T pinion.The GPM steel pinions are profile regraded. This allows for a change in gearing by a pinion swap alone. Module: m=1.5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
Similar products
With the Big Scale-EXTREME an adjustable clutch for very special requirements has been designed:For large-displacement enginesFor heavy or high traction cars (Losi, HPI)For modified performance enginesFor the demanding off-road useRapid wear of a clutch is a sign of constant slipping, even beyond engagement speed. In this case, the clutch does not transfer the applied torque.This is where the Big ScaleEXTREME sets a new standard.The new design of the "Extreme" prevents the centrifugal forces of clutch springs or lever side of the clutch shoes from counteracting the centrifugal force of the friction pad side even after engagement.As a result this clutch can transfer lots of power with minimal wear.The new design ensures that the centrifugal forces are transferred in full to the clutch lining. Precise engagement and disengagement even under high loads and inside of closed clutch bell carriers means no problem for this clutch.The clutch can be easily adjusted to the engagement speed through three set screws without clutch bell removal, so you can match the characteristics of your engine.The special clutch lining of the Big Scale-EXTREME is particularly wear-resistant and - especially in combination with a high-quality nitrited clutch bell (), guarantees for an exceptionally long service life! Contrary to the "Cross" or "Race" version there's no need to uninstall the clutch from the engine for maintenance. All parts are easily accessible from the front after removing the front plate.Please see the specifications tab for further information and handling advices!The regular price of the Big Scale-EXTREME is EUR 139.90
Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM clutches Big Scale Extreme and Cross.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.
The GPM 18T steel pinion is profile regraded. This allows for a change in gearing by a pinion swap alone. The pinion has the same dimensions as the HPI 17T stock pinion.Module: m=1,5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
Regular price Big Scale Clutch: 109,90 EUR Nitriding hardened clutch bell: 40,50 EUR complete price:.......................150,40 EURAdjustable 3-shoe clutch for:Zenoah / Chung Yang / HPI - Fuelie / Smartech PT and many other engines.The delivery content:- y0730 GPM Big Scale-Cross adjustable 3 shoe clutch, 1 pce. - y0729 Gas-nitrited tuning clutch bell for HPI Baja, 1 pce. The Gas-nitrited tuning clutch bell:Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding. Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch. Suitable for genuine slot drive HPI pinions. Comes with bolts and spring washers included.The GPM-Big Scale clutch:Suitable for racing and for the ambitious hobbyist driver. Unlike the stock clutch, the installed GPM-Big Scale clutch can be adjusted by turning one single screw. A 2.5 mm allen key wrench is required for this application.Therefore it is possible to precisely adjust the clutch engagement depending on track characteristics.Handling instructions for three-shoe clutches y0730 GPM Big Scale Cross and y0731 GPM Big Scale RaceInstallation:The GPM Big Scale clutch will be bolted to the crankshaft using the supplied CSH-screw.It should be noted that the use of thread locking compound on that screw is neither necessary nor recommended!Removal:Remove the CSH-screw with a 4mm Allen wrench; then insert a suitable M8 bolt and remove the clutch from the crankcase cone by tightening that bolt. Hole for adjustment:For clutch adjustment without removing the clutch bell a 4 4.5 mm hole must be drilled into the clutch bell for access to the adjustment screw. Placement of the hole depends on clutch bell dimensions and car; so you have to make your own measurements for the placement of the hole.It is important that the drilled hole is thoroughly deburred (at least on the inside of the clutch bell) to prevent excessive clutch pad wear. Breaking in:A new clutch or shoes fitted with new pad should always be broken in. Therefore the clutch engagement speed should not be too high for the first tank of fuel. This gives the lining the possibility to adjust to the clutch bell without glazing. The only difference between two clutches is the clutch spring rate, which provides the optimal range for clutch engagement depending on the application. The three available versions of clutch springs provide adjustability within the following RPM ranges:Silver springs 1.3 mm y0730/05 (standard on Big Scale Cross): 5,000 9,500 RPMGold springs y0730/06 1.4 mm (standard on Big Scale Race): 6,500-11,500 rpm Adjustment:Adjustment of the clutch engagement speed is done by one single screw using a 2.5 mm Allen wrench. Turning the screw in increases the stall speed, backing it out will lower the stall speed. The adjusting screw is thread locked to keep the setting. Should you realize that the screw can be turned too easily please re-apply medium strength thread locking compound.Finding the best clutch engagement speed:The best clutch engagement speed should be found while driving on the track, it depends on engine characteristic, track layout, track surface and driving style.It is recommended to start with the lowest setting (which means the set screw just touching the adjustment cam) and gradually turning the adjusting screw in while doing test runs after every adjustment.If you feel that you have exceeded your best engagement speed (clutch will slip too much), back the screw out for a little bit to avoid excessive wear or glazing of the pads.Attention: You must use adhesive y0743 Clutch-Safe when replacing clutch pads!
Complete set with clutch bell and one each 17T and 18T steel pinion.GPM clutch bell with 5 mm pinion bolt. CNC-machined one-piece bell for absolute true running. Inclusive mountings.GPM 17T and 18T steel pinions are profile regraded. This allows for a change in gearing by a pinion swap alone.Module: m=1,5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Content of delivery:GPM steel clutch bell SBJ613GPM steel pinion 17T SBJ017TGPM steel pinion 18T SBJ018TO
Regular price: 54,80 EURSteel pinion set with one each 17T and 18T pinion.The GPM steel pinions are profile regraded. This allows for a change in gearing by a pinion swap alone. Module: m=1.5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
Complete set with clutch bell and one each 16T and 18T steel pinion.GPM clutch bell with 5 mm pinion bolt. CNC-machined one-piece bell for absolute true running. Inclusive mountings.GPM 16T and 18T steel pinions are profile regraded. This allows for a change in gearing by a pinion swap alone.Module: m=1,5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Content of delivery:GPM steel clutch bell SBJ613GPM steel pinion 16T SBJ016TOGPM steel pinion 18T SBJ018TO
The GPM 16T steel pinion is profile regraded. This allows for a change in gearing by a pinion swap alone. The pinion has the same dimensions as the HPI 17T stock pinion.Module: m=1,5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
Extremely strong 17T steel pinion from GPM, fits all HPI Baja 5B / SS / 2.0 and 5T, Carson Wild GP Attack. Profile regraded, it fits to the original Baja pinion Nr. 85432
Customers also viewed
Normal price: 249,90 EUR Tuning front disk brake system for the HPI Baja 5B/SS/5T/5sc, the conversion kit includes all necessary parts. The brake includes the finest parts available for a cable brake and has the following features: * uses existing mounting points for all parts * brake pads and 70 mm diameter stainless rotors made by RS-5, the best performing combination available * hardened stud bolts for the brake pads * billet brake levers, no tweak and best transfer of servo power * ultraflex bowden cables * brake cams run in hardened steel bushings and brass guide plates (miniature bearings don't last in offroad cars) * billet alloy bowden cable support block with adjustment screws * billet alloy bowden cable mounts at the calipers * pre-assembledOn a 5T the stud bolts which hold the brake pads will interfere with the ribs in the rim. However, modifying the rim or swapping the stud bolts for long csh screws allows for installation on a 5T.Spare parts for this brake as a PDF-file with spare part numbersWe highly recommend the installation of a stronger throttle servo to take full advantage of this brake system. The is an excellent choice.
GPM air filter cover which fits easily over your existing air filter. A rubber band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments. Fits all common filters, foam or fabric (K&N) style.
Genuine HT spare/option part. Gas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.Contents:1 piece
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:5315 Clutch block carrier5315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch