LOS252056 Losi Dogbone 174 mm, Center, Front, DBXL-E

Genuine Losi spare/option part. Contents:1 piece

With complete RTR equipment y1382 Original Maxi-Pin 1/6 offroad competition tire The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder comes with completely installed remote control. Just fuel up, start the engine and drive off.Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm

Genuine Losi spare/option part. Contents:1 set

Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!

Genuine Losi spare/option part. Contents:1 piece

This stadium truck is the perfect model for the entry into the RC large scale sport. The model is fully assembled and can be equipped with an RC system in our shopping cart selection. It is available with Lexan body shell. Limited Edition tune parts:2x 4492 Alu Querlenker hinten untenPreis: 55,70 EUR1x 4475/01 Rear alloy shock mountPrice: 96,10 EUR1x 6423 Gear protectorPrice: 20,70 EUR1x 6499 Alloy front shock towerPrice: 69,70 EUR4x 18001 Alloy a-armPrice: 131,60 EURBase price Stadium Truck Sportsline829,90 EURSurcharge tuning parts:373,80 EURRegular price Limited Edition:1203,70 EURThe Stadium Truck comes top equipped as standard and also offers numerous choices for additional option parts to increase driving performance.Product details:1/6 scale 2WD Stadium Truck with double wishbone independent suspension. 4 mm metal chassis plate. All holes on the underside are countersunkFuel tank and RC components are protected by the bevelled chassis>Adjustable toe-in/out on the front suspensionAdjustable camber on the rear suspension4 large-volume oil pressure shocks absorbers with adjustable spring tension for a smooth ride. The secondary spur gears, differential gears and all drive parts are case hardenedThe stadium truck comes with a powerful 26cm³ FG 260 internal combustion engine. This requires standard 2-stroke gas/oil mix available at every gas station.With a tank capacity of 0.7 litres, a driving time of approx. 40 minutes is achieved.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery DimensionsLength: 730 mmWidth: 510 mmHeight: 360 mmWheelbase: 470 mm