Kamitiro FG parts set for Marder 4wd kit, y0089
Product information "Kamitiro FG parts set for Marder 4wd kit, y0089"
Includes:
1x 6050, spur gear carrier
1x 6051, rubber pucks
1x 6427, plastic spur gear 46T
1x 6431 oder 6431/1, steel pinion 16T
1x differential, complete
1x 6048 oder 6048/1, differential spur gear 48T
2x 6069/1, differential drive cups
1x 6074/1, a-arms, rear upper
1x 6076/1, a-arm turnbuckles
1x 6050, spur gear carrier
1x 6051, rubber pucks
1x 6427, plastic spur gear 46T
1x 6431 oder 6431/1, steel pinion 16T
1x differential, complete
1x 6048 oder 6048/1, differential spur gear 48T
2x 6069/1, differential drive cups
1x 6074/1, a-arms, rear upper
1x 6076/1, a-arm turnbuckles
Login
Similar products
Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
federn_dirt_m Version:
y0323/05 - M15, blue
Progressive tuning springs, will fit the standard red and the thick silver shocks on FG offroad cars. The rear springs will also fit Hurrax shocks. All springs have an internal diameter because of the manufacturing progress: 21 up to 21,5 mm. Available in several versions: For the front on FG 2WD buggies:y0322/01 - M1, 2,1 x 50 mm, yellowy0322/02 - M2, 2,2 x 50 mm, orangey0322/03 - M4, 2,4 x 50 mm, purpley0322/04 - M5, 2,5 x 50 mm, blueFor the rear on FG buggies, front and rear on FG monster cars and 4WD buggies:y0323/01 - M11, 2,1 x 90 mm, yellowy0323/02 - M12, 2,2 x 90 mm, orangey0323/03 - M13, 2,3 x 90 mm, redy0323/04 - M14, 2,4 x 90 mm, purpley0323/05 - M15, 2,5 x 90 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackFor the front on FG buggies:y0324/01 - M01, 2,1 x 60 mm, yellowy0324/02 - M02, 2,2 x 60 mm, orangey0324/03 - M03, 2,3 x 60 mm, redy0324/04 - M04, 2,4 x 60 mm, purpley0324/05 - M05, 2,5 x 60 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackContents:2 pieces
Genuine HT spare/option part.For secure installation of the brake cables.Contents:1x Brake cable bracket2x Socket head cap screws 3 x 25 mm2x Self-locking hexagon nut M3
Genuine FG spare/option part.CNC-manufactured front axle mounts A and B in alloy with rebound stop. The borings for the wishbone pins are equipped with guide bushes. Suitable for Marder, Marder Race, Beetle On-/Off-Road and Monster models.Contents:1 set
Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces
federn_dirt_m0 Version:
y0324/05 - M05, blue
Genuine HT spare/option part. Progressive tuning springs, will fit the standard red and the thick silver shocks on FG offroad cars. All springs have an inner diameter of 21 mm.Available in several versions.For the front on FG buggies:y0324/01 - M01, 2,1 x 60 mm, yellowy0324/02 - M02, 2,2 x 60 mm, orangey0324/03 - M03, 2,3 x 60 mm, redy0324/04 - M04, 2,4 x 60 mm, purpley0324/05 - M05, 2,5 x 60 mm, blueContent:2 pieces
Genuine HT spare/option part.Set includes shock tower Marder y1032, fits Marder, Beetle, Pajero, Monster Beetle Aluminum bulkhead brace for y1031.Contents:1 set
clipse_griff Size:
y0264/06 - 6 mm
Genuine HT spare/option part.Quick change clips for installation and de-installation without tools, galvanic zinc plated.Spring steel, hardened and tempered to 1450 to 1600 N/mm² tensile strength.Available for 4, 5 and 6 mm shafts.Contents:10 pieces
Two wheel squares with 3mm dowel pins. Like FG 6106/07, but made from heat treated steel. Significantly reduced wear. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled. Pins should be fitted using high strength thread locking compound.Measures:18 mm square11.5mm wideBore diameter 8 mm
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces
Customers also viewed
Genuine FG spare/option part. Individual prices of the parts in the tuning set: 847,06 EurosAluminum conversion kit to aluminum front axle and aluminum rear knuckle and wishbone for FG Marder.Contents:1 set
The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder is also available with completely installed remote control. Just fuel up, start the engine and drive off.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm
2 pairs of shock absorbers, set
Please select shock absorber version!
Check which version you need!
y1137/01 for FG, Carson 2 WD models
y1137/02 for FG Monster/Stadium Truck 2 WD models
y1137/03 for FG Marder/Offroad Buggy 4 WD models
Y1137/04 for FG Monster/Stadium Truck 4 WD models
y1137/05 for Carson 2 WD models
y1137/06 for Kyosho Scorpion XXL models
y1137/07 for Carson C5 and FG Sportsline TW models
Y1137/08 for FG Evo models up to 2014
y1137/09 for FG Evo 2020 models from 2015 onwards
GPM-Spezial Cross shocks, premium full metal version.Assembled and filled.Special features:
16 mm shock bore for increased capacity
volume compensation
shock body and caps machined from billet aluminum
hard anodized shock body
machined precision delrin pistons (not injection molded!)
aluminum shaft end and spring retainer
shock caps with replaceable bushings
factory filled with 1000
GPM-Spezial Cross shocks, premium full metal version. >Assembled and filled.
volume compensationshock body and caps machined from billet aluminumhard anodized shock bodymachined precision delrin pistons (not injection molded!)aluminum shaft end and spring retainershock caps with replaceable bushingsfactory filled with 1000 filling quantityshort 7mllong 9mlLong and short version availble in the following sets:
y1137/01 Version 1
FG 2WD: Marder, Off-Road Buggy, Beetle, Monster BeetleCarson 2WD: Comanche, Attack Evo, CRT, CPT, Smartech Monster-Truck
Set includes: 2 each long and short shocks
y1137/02 Version 2
FG 2WD: Monster-Truck, Monster Jeep, Monster Hummer, Monster Beetle Pro, Stadium Truck, Stadium Jeep, Stadium Hummer
Set includes: 4 long shocks
y1137/03 Version 3
FG 4WD: Marder, Off-Road Buggy
Set includes: 4 long shocks, one pair features 5 mm upper mounting bore
y1137/04 Version 4
FG 4WD: Monster-Truck, Monster Jeep, Monster Hummer, Stadium Truck, Stadium Jeep, Stadium Hummer, Off-Road Beetle
Set includes: 4 long shocks with a 5 mm mounting hole in the upper shock cap; 1 pair with standard lower shock mounts, the other pair with long lower shock mounts (4WD MT version)
y1137/05 Version 5
Carson 2WD: Attack, Super Attack, Gas Blaster, Big AttackSmartech 2WD: UNO, Spider, Duratrax, Firehammer
Set includes: 2 each long and short shocks with spacers for the front
y1137/06 Version 6
Kyosho Scorpion XXL
Set includes:4 short shocks with long shock mounts
y1137/07 Version 7
Smartech C5 and FG Sportsline 1:5 touring cars 2WD and 4WD
Set includes: 4 short shocks equipped with shock mounts
y1137/08 Version 8
FG-Evo Modelle: 2008 - 2011 and Evo from 2012 an up
Set includes: 4 short shocks equipped with shortened shock mounts
y1137/09 Version 9
FG-Evo Modelle:2020 and 2020.1 from 2015
Set includes:4 short shocks equipped with shortened shock mounts
Overall length, extended: long 155 mm, short 131 mm
Mounting distance, extended: long 144,5 mm, short 120,5 mm
Travel: long 43,5 mm, short 30,5 mm
Inner diameter of spring: 21 mm
Shock body diameter: 20 mm
Eye bore: 4.5 mm
Eye thickness: top 6 mm, bottom 5 mm
Shaft diameter: 4 mm
Shaft thread: M4
We recommend our progressive y0452/02. for these shocks. On FG cars the OEM springs can be used as well. Shock versions y1137/07 and y1137/08 for Smartech C5 and FG on-road cars should use spring Shock oil recommendations:The GPM-Spezial Cross shocks are factory filled with 1000 viscosity silicone oil. This gives a very good shock performance at normal ambient temperatures.When a softer shock is required, you can go for 500 or even 600 viscosity oil; 1500 and up if you prefer more damping.One 50 ml bottle fills 5 long or 6 short shocks.For use in a Kyosho Scorpion XXL (version 6), the shocks must be installed with an additional 4 mm spacer at the lower front mount (see picture above). The stock Scorpion springs can be used. We suggest silicone oil with a 100 to 200 viscosity for the front and a 200 to 300 viscosity for the rear .Introductory price! Regular price: 129,90 EUR / set
Genuine FG spare/option part. Fits FG 2WD Marder.Offer your Marder a new life - it will be out of all recognition! Aggressive in the curves, dead on the line - just everything which guarantees pure driving fun. The well-tried 4WD by FG is now available as conversion kit for your 2WD Marder. You will not realize from the outside that the model is equipped with a fourwheel drive. But you and your rc-car friends will notice it considerably as soon as you start your model and speed up properly.The conversion kit includes all parts necessary to convert your 2WD Marder to a 4WD Buggy. A mounting instruction is enclosed.Please note: the radio plate is designed to accept a 805-sized servo (case length 65 mm). For installation of a Rhino (case length 58 mm) or a similar sized servo you need to order radioplate 68241 separately.Contents:1 set
Complete pre-assembled set front disc brakes for FG Marder, FG Off-Road Buggy and for Carson / Smartech Attack / Comanche / UNO / Monster Truck / CRT / CPT / Super Attack / Evo Attack / Spider / Big Attack , fits Conrad Big Pyro as well.For mounting in a Gas Blaster you must change you front shock mount and the front body shell holder, look at the pictures. Includes:- brake system with linkage- uprights- bearings- longer axle shafts- wider square drivesNo additional parts needed.
Item N° 68510 Electric conversion kit 1:6 2WD for 465 Wheelbase, setSuitable for 2WD Buggy and Monster models as Marder, Beetle, Monster-Truck, Hummer, Jeep a.s.o with 465 mm wheelbase.This conversion kit is suitable for the 2WD FG models Marder, Beetle, Off-Road Buggy and Monster models with 465mm wheelbase. Suitable for the electric engines from FG Modellsport, Leopard BL engines and Castle Creation. The conversion kit includes gear and engine mount, fixing parts for cruise control and LiPo batteries. Cruise control, BL engine and LiPo batteries are not included. During the conversion several fixing holes have to be applied to the chassis. Gear transmission has to be changed accordingly to the use of the electric engine.For easy mounting we recommend LiPo batteries with a max. length of 150mm and 50mm width.The conversion kits include all mechanical parts (except electric engine with speed control, Lipo batteries) to convert your FG model scale 1:5 and 1:6 to an electric powered system.
Genuine FG spare/option part. Precise, solid and reliable, for use at competitions, not adjustable.Suitable for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster/Stadium models 4WD RTR.Content:1 set