Genuine Smartech spare/option part.Module: m=1,5.Content:1 piece
Genuine Smartech spare/option part.Module: m=1,5.Content:1 piece
Module: m=1,5
Reinforced stiffer plastic compound
Genuine Smartech spare/option part.Module: m=1,5.Content:1 piece
Reinforced stiffer plastic compound
Reinforced stiffer plastic compound
Reinforced stiffer plastic compound
Genuine Smartech spare/option part.Module: m=1,5.Content:1 piece
Item N° 6451/03 Air filter adapter for Zenoah and CY, 1pce.These air filter adapters are needed fpr mounting the FG air and inlet silencers 6464, 6465 and the K+N air filters 6442 and 6460 as well as 9462 and 6466 on Solo, Zenoah and Tech engines.Fits: Zenoah G230/G240/G260/G270/G290 and CY 23/26 cm³ engines.
Item N° 6465 FG air filter for 1:6 Off-Road models complete - setYou will need the adapter plate 6451/03 for installation.
Item N° 905046 Carson tuned pipe for Carson Gas Devil + CRT 4x4, Conrad Hell Devil, Smartech Titan - setLow mounting alloy pipe, installs between the wheels. Comes complete with manifold and mounting hardware.When installing this pipe on a Thunderbolt some minor modifications to the body shell are necessary to clear the manifold.
GPM air filter cover which fits easily over your existing air filter. A rubber band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments. Fits all common filters, foam or fabric (K&N) style.
Alloy case conversion kit for Carson Gas Devil 4x4 (Smartech Titan) only, can be used for all differentials.Comes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings.
Genuine HT spare/option part. Nitrited steel gears, fit Carson Gas Devil / Smartech Thunderbolt 4x4 only.These gears are available with 37T or 40T, both share the same diameter and must be used in combination.Please note: the gears cannot be used in combination with the stock gears and the 37T version is no replacement for the stock 37T gear!This gives you the following new gear ratios:I=10.58I=9.79 (when using two identical gears !)I=9.06The stock gear ratio is I=11.38 and I=8.42 is possible by switching the gears.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Contents:1 piece
Machined alloy version replaces the stock stamped part, 5 mm high strength alloy.
Machined alloy version replaces the stock stamped part, 5 mm high strength alloy.
Machined alloy version replaces the breakage prone plastic stock part.
Genuine Smartech spare/option part.Machined alloy version replaces the breakage prone plastic stock part.Suitable for Smartech Gas Devil + CRT 4x4, Conrad Hell Devil, Smartech Titan.Content:1 piece
Tweak resistant alloy servo mount to replace the stock plastic part.Distance between servo mounting threads: 18 mm.
Cardan drive shafts fits on Carson Gas Devil + CRT 4x4, Conrad Hell Devil and Smartech Titan on front or rear axle. Does not fit Thunderbolt!Universal joint diameter: 18 mmLength over all: 190 mmDistance between joints, center/center: 119 mmBall diameter: 10 mmAxle shaft diameter x length: 8 mm x 53 mm
Set includes 2 rotors, 4 brake pads and 4 return springs. The steel rotors will last significantly longer on the differential drive cups, wear between rotors and brake pads is reduced as well.
Item-No.: s054320/01Brake pads for Smartech tuning brake