AT-5T014 ATOP Ball-raced servo saver for Losi 5ive-B/T and Mini

€89.90*

Prices incl. VAT plus shipping costs

Available

Product number: at_5t014

EAN: 4058575110330

Product information "AT-5T014 ATOP Ball-raced servo saver for Losi 5ive-B/T and Mini"

Genuine Atop spare/option part.

Ball-raced servo saver and steering assy for Losi 5ive-B/T and Mini.

Replaces all stock parts between steering servo and steering rods except for the servo saver shafts. With ball bearings all around and dual linkages between servo and servo saver steering precision is greatly enhanced.

Complete set with ball-raced servo saver, ball-raced centerlink, full metal second side servo linkage and installation hardware.

Content:

1 set

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€37.90*

y0424 Extension cable, Futaba/universal

akku_0019 Length: y0424/01 - 10 cm

Genuine HT spare/option part. In case the servo cable is not long enough.Two selectable lengths:y0424/01 - 10 cmy0424/02 - 25 cmContents:1 piece

€6.80*

TT1000 Top Tuning Electronic 20 Amp Bigscale high voltage 30 Volt switch

tt_tt1000 Connector: TT1000/01 Universal in - Universal out

Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece

€39.90*

y0428 Extension cable universal180/300 mm

y0428 Length: y0428/01 - 180 mm

In case the servo cable is not long enough.Two selectable lengths:y0428/01 - 180 mmy0428/02 - 300 mm

€5.90*

LOSB 9642 Global AC 6V Charger 5T

Genuine Losi spare/option part. Contents:1 set

€29.99*

AREA-5T-012/04 Screw set for AREA-5T-012

area_ar_l012_04 Version: AREA-L012/02-03 Hitec 5765 / Rhino Digi 4 and similar

Genuine Area spare/option part.Replacement part for: AREA-5T-012 radio plate set for Losi 5ive-T and Mini.Content:1 piece

€14.90*

y0425/02 Y-harness current, universal connector

Genuine rc-car-online spare/option part. Total length:approx. 200 mmContents:1 piece

€14.90*

This product is no longer available.

AREA-5T-012/02-01

area_ar_l012_02_01 Version: AREA-L012/02-04 for either Losi-OEM orSavöx 236 sized servos

Genuine Area spare/option part.The plate fits Losi stock servos.Replacement part for: AREA-5T-012 radio plate set V3 for Losi 5ive-T and Mini.Content:1 piece

€79.90*