Product information "AKX018 GPM additional heat sink with fan for Arrma Kraton / Outcast 8S"
Genuine GPM spare/option part.
Milled 6061T6 aluminum additional heat sink from GPM with larger 12 volt fan (60 x 60 x 15 mm) for Arrma Kraton / Outcast 8S. The additional heat sink also serves as an adapter plate to mount the larger fan on the original heat sink. A machined contact guard for the intake side of the fan is also included.
The fan is connected to the EC5 connector of a 3S or 4S drive battery using an adapter cable (included). Thus, the operating current does not have to be provided by the ESC's BEC.
The overall height of the unit, measured from the bottom of the additional heat sink is about 30 mm.
Contents:
1 set
0 of 0 reviews
Average rating of 0 out of 5 stars
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
Powerful cooling fan with bracket for installation on FG electric gear plate 66516 (touring cars and off-road models) or chassis strut 10701 (Formula 1).The 60 x 60 x 24 mm TT1028 fan provides way more air flow than the two original fans combined. A chrome-plated steel grille on the intake side protects the fan.Two bracket lengths are available. The short version is intended for motors up to approx. 80 mm overall length. This applies e.g. to all standard FG motors. For longer motors we recommend the long bracket for a better position of the fan over the motors cooling fins. Performance data of the fan: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 - 8.4 V Current: 0.5A Speed: 8.500 1/min @ 8.4 V Flow rate: 39.2 CFM Scope of delivery: Fan TT1028 Short fan mounting frame Protective grille for fan Adapter cable to JR connector Installation hardware
Genuine Top Tuningspare/option part. High performance fan as upgrade for various applications in electric models.The size 50 x 50 x 15 mm can be swapped e.g. for the fan of the ARRMA motor cooling unit or the fans of different speed controllers (e.g. ZTW Beast 200A). The ARRMA application requires approx. 5 mm longer screws due to the 5 mm taller fan (M4x25).The air flow rate is much higher than with the standard units!The operating voltage of the fan with 5 - 8.4 V is perfectly adapted to these requirements. Technical data: Dimensions: 50 x 50 x 15 mm Operating voltage: 5 8.4 V Current: 0.65A Speed: 10,000 rpm @ 8.4 V Air flow: 28.3 cfm Connector: BEC female Cable length: approx. 30 cm Contents:1 piece
Genuine Top Tuningspare/option part. High performance fan as upgrade for various applications in electric models.The size of 40 x 40 x 10 mm can be swapped e.g. for the fans of the FG motor cooling unit or the fans of various speed controllers.The air flow rate is much higher than with the standard units!The operating voltage of the fan with 5 - 8.4 V is perfectly adapted to these requirements. Technical data: Dimensions: 40 x 40 x 10 mm Operating voltage: 5 8.4 V Current: 0.65A Speed: 16,000 rpm @ 8.4 V Air flow: 16.7 cfm Connector: Dupont 2-pin female (compatible with BEC/Futaba/Universal) Cable length: approx. 17 cm Contents:1 piece
Powerful cooling fan with bracket for installation on FG electric gear plate 66516 (touring cars and off-road models) or chassis strut 10701 (Formula 1).The 60 x 60 x 24 mm TT1028 fan provides way more air flow than the two original fans combined. A chrome-plated steel grille on the intake side protects the fan.Two bracket lengths are available. The short version is intended for motors up to approx. 80 mm overall length. This applies e.g. to all standard FG motors. For longer motors we recommend the long bracket for a better position of the fan over the motors cooling fins. Performance data of the fan: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 - 8.4 V Current: 0.5A Speed: 8.500 1/min @ 8.4 V Flow rate: 39.2 CFM Scope of delivery: Fan TT1028 Long fan mounting frame Protective grille for fan Adapter cable to JR connector Installation hardware
Genuine Top Tuningspare/option part. High performance fan as upgrade for various applications in electric models.The size 60 x 60 x 24 mm can be swapped e.g. for the fan of the ZTW Beast 300A speed controller. For this particular application, M4x40 screws are required instead of the standard M4x30 screws due to the 9 mm taller fan.The air flow is considerably higher than with the standard units!The operating voltage of the fan with 5 - 8.4 V is perfectly adapted to these requirements. Technical data: Dimensions: 60 x 60 x 24 mm Operating voltage: 5 8.4 V Current: 0.5A Speed: 8,500 rpm @ 8.4 V Air flow: 39.2 cfm Connector: BEC female Cable length: approx. 30 cm Contents:1 piece
Like every component in the Spektrum Smart ecosystem, Firma Smart ESCs combine "plug-and-play" simplicity with the ability to communicate with other Smart electronics together, creating the best-performing RC system for your vehicle imaginable.Firma Smart ESCs do much more than regulate power. They function like a virtual engineer inside your model, providing a direct path to the vital operating data you need to reach peak performance. Firma Smart ESCs give you an extra layer of confidence that your electronics are all operating at their best.With Firma Smart ESCs, you'll be better connected to your vehicle than ever before without installing extra components that all work independently of each other. You won't need extra wires, modules, or links. A Firma electronic speed control provides a one-wire solution for obtaining telemetry data such as RPM, temperature, battery voltage and capacity.Firma ESCs not only gather the data but also send it to your transmitter in real time, instead of only storing it for after-run study. You're able to adjust settings as needed to boost performance on the go. The Firma Smart single-wire telemetry solution has been tested for quality and performance by the best brands in RC. Their verdict? Smart technology is both simpler and superior!Product Features Smart all-in-one telemetry Fast, powerful 32-bit ARM M4 processor Waterproof Multiple options for easy programming: Button programming Smart ESC Programming Box SmartLink USB Updating and Programmer application Multi-point protection: Over-current protection Automatic LiPo low-voltage cutoff Thermal protection Failsafe protection Developed and designed by Spektrum engineers, in partnership with the industry's leading ESC manufacturer Compact for easy installation in most applications Ready to install no soldering required Rugged plastic case with mounting tabs Aluminum heat sink for high efficiency Cooling fan Adjustable high-power BEC Firmware updatable through the Smart ESC Programming Box High heat-resistant IC connectors, backwards compatible with EC connectors WATERPROOF The all-weather, waterproof design of Spektrum Firma Smart ESCs allows them to perform in nearly any terrain under almost any conditions. Firma ESCs keep you going through dust, gravel, snow, and water. EC3/EC5 BACKWARDS COMPATIBLE Firma ESCs feature IC series battery connectors. The IC series of connectors are designed from the ground up to provide a more solid connection, higher heat resistance, and effortless installation. When used with an IC3 or IC5 connector-equipped Spektrum Smart battery, the ESC can receive and transmit battery telemetry data. EC3 and EC5 are also compatible with Firma ESCs for basic operation and ESC telemetry. ONE-WIRE TELEMETRY No need to connect multiple wires, sensors, modules, and links. With Firma ESCs, simple one-wire telemetry transmits a wide range of data directly to your transmitter in real time, including RPM, voltage, temperature, balance, capacity, and speed. ONE-WIRE TELEMETRY No need to connect multiple wires, sensors, modules, and links. With Firma ESCs, simple one-wire telemetry transmits a wide range of data directly to your transmitter in real time, including RPM, voltage, temperature, balance, capacity, and speed. SMART TECHNOLOGY BATTERY DATA When used with a Spektrum Smart LiPo battery, your Firma ESC provides you with the benefit of battery telemetry that's automatically transmitted to your compatible Spektrum radio in real time. On your transmitter screen you'll be presented with helpful information such as number of cycles, battery percentage, individual cell voltage and more! MULTIPLE PROGRAMMING OPTIONS Multiple programming options are available. Button programming can be used with nothing more needed. Using the Smart Firma ESC Programming Box, you can easily change settings at the track to suit driving conditions. An easy-to-use Smart Link USB Updating and PC Programmer app is also available. FAST, POWERFUL M4 PROCESSOR The Firma ESCs' 32-bit M4 processor produces higher resolution signal input and more accurate motor output.
The 2WD-465 Sportsline electric model is based on a short chassis (465 mm wheelbase) with double wishbones Rear and front axles built. The vehicle is factory equipped with the 2-damper front axle.In the unpainted version Version does not include a decal sheet!Features: TT5692 Top Tuning Brushless Motor 1090 kVy1567 ZTW Beast Pro 200A regulatorThe front axle of the GT2 was widened to 384 mm. The rear axle is 395 mm wide.With 1090 KV brushless motor (item no. TT5692) and with 200A controller (item no. y1567).< /font>Chassis short 465 with double wishbones on the rear and front axle completely assembled, ball bearings, differential gear, oil pressure shock absorber, multi-part unpainted polycarbonate body (item no. 05160L), white spoke rims, tires and tire inserts.
The model is also available in our shop selection including complete RTR equipment! RTR features RTR = Ready to Run. The RTR version is delivered ready to drive and with the 2.4 GHz remote control installed. Transmitter: Reflex Wheel Pro III 2.4 GHz Receiver: Mini BECy1570 CYS S0650 large model servo, 40 kg/0 .11 secTransmitter batteries 4 pieces y0660/04
Paint: selectableDecor set: selectable (included in the painted version)
Genuine ARRMA spare/option part. This EXtreme Bash (EXB) specification Front Brace Mount is CNC machined from high-quality aluminum to add strength and stiffness to your ARRMA vehicleFeaturesARRMA EXtreme Bash (EXB) parts are made from extremely strong and durable materials and engineered to survive the most grueling actionPrecision CNC machined for accurate fit to the center gearbox of your vehicle - Anodized red for awesome ARRMA looks - Adds strength and stiffness to mounting between the center brace and gearbox of your vehicleContents:1 pieces
€34.99*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).