8384/02 FG Tank replacement sealing
€2.10
Available
Product information "8384/02 FG Tank replacement sealing"
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Alternatives
Genuine FG spare/option part.This fuel cap tuning seal ensures a perfect seal of your fuel tank (items 8380/06, 8380/08 are not included).Drill with an 8 mm hole through the tank lid. Insert seal # 8384/02 into the neck of the lid.Insert seal # 8380/06 along with the aluminum cover with sealing ring into the plastic lid (# 8380/08).Tighten the complete assembly with the included nut, and finally add vent fitting # 8381/03.Reinstall the lid onto the tank.Content:1 set
Genuine FG spare/option part. 700 ml fuel tank with snap closure, ventilating valve, fuel filter and fuel hoses.Dimensions:Length: 152 mmWidth: 102 mmHeight: 70 mm and with fuel cap 95 mmContents:1 piece
Item N° 08383 Fuel tank 800ml with quick acting closure, 1 pce.800 ml fuel tank with snap closure, ventilating valve, fuel filter and fuel hoses.Dimensions:Lenght: 130 mmWidth: 100 mmHeight: 100 mmVolume: 800 ml
Customers also bought
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Item N° 7197 Damper spring progressive 2,3x68mm yellow, 2 pce.Suitable for all FG shock absorbers and also for other makes with an outside diameter of 16mm.Measures:Length: 68 mmOutside diameter: 21 mmWire diameter: 2,3 mm
Genuine FG spare/option part.Simple but very effective volume compensator, 100% sealing. Suitable for all FG aluminium shock absorbers 16mm and 20mm. Substitute for volume compensator 7088.Contents:2 pieces
Genuine FG spare/option part.The set contains FG no.: 6042/05, 6044/05, 7041/05 and 8456/05. Is used to optimize the rear brake (FG no. 7497).Contents:1 set
Shim rings to compensate the axial play of the shaft, to use as washers a.s.o.Part is delivered in silver or black color from vendor!
Genuine FG spare/option part.Suitable for all 1:5 models.Dimensions:Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Contents:1 piece
Customers also viewed
Genuine FG spare/option part.Suitable for FG 7347 and FG 7348.Hint:For installation on a Losi DBXL tank the mounting hole of the DBXL tank must be enlarged to 23 mm diameter.Contents:1 piece
Item N° 08383 Fuel tank 800ml with quick acting closure, 1 pce.800 ml fuel tank with snap closure, ventilating valve, fuel filter and fuel hoses.Dimensions:Lenght: 130 mmWidth: 100 mmHeight: 100 mmVolume: 800 ml
Suitable for all FG/Carson/Smartech cars except FG Evo and Carson 4WD.Please note that tank mount 7143 is required for installation. Installation in a Carson/Smartech 1/6 off-road car requires drilling of two new 4.5 mm diameter holes into the chassis plate. Drilling template is included.Comes as shown with fuel lines, grommet and gas cap included.
Genuine Losi spare/option part. Contents:1 piece
Genuine FG spare/option part.The set contains FG no.: 6042/05, 6044/05, 7041/05 and 8456/05. Is used to optimize the rear brake (FG no. 7497).Contents:1 set
Genuine FG spare/option part.This fuel cap tuning seal ensures a perfect seal of your fuel tank (items 8380/06, 8380/08 are not included).Drill with an 8 mm hole through the tank lid. Insert seal # 8384/02 into the neck of the lid.Insert seal # 8380/06 along with the aluminum cover with sealing ring into the plastic lid (# 8380/08).Tighten the complete assembly with the included nut, and finally add vent fitting # 8381/03.Reinstall the lid onto the tank.Content:1 set
Genuine Mecatech spare/option part. Contents:1 piece