Genuine FG spare/option part.Body detail kit with different rearview mirrors, windscreen wipers and aerials to give the Touring car bodys a more detailed look.Contents:1 set
Genuine HT spare/option part.Fits 535 mm wheel base, current touring car width. A rear wing is available through the shop's options menu. The body shell comes without decals!Required body mounts:Front section: FG 7020/11 Front bumperRear body mount: FG 7152/01 Rear body supportSide front: FG 7012 Body mountSide rear: FG 7014 Body mountAvailable decal sheets:y1329 - Vehicle decalsy1320/01 - Team decals Posty1329/02 - Team decals Samsungy1329/03 - BMW-Bank decalsy0683 - Jägermeister decalsy3006 - rc-car-online decalsDimensions:Length: 885 mmWidth: 392 mmHeight: 260 mmWheel base: 530 mm
Fits on all standard width touring car chassis' with 530 mm wheelbase, FG, Carson C5 chassis and most other 1/5 touring cars with the same wheelbase. The body shell is vac-formed from 2 mm Lexan. Replacement parts: 5192 FG Front Porsche 911 GTR3 R clear 5193 FG Rear Wing Porsche 911 GTR3 R clear Required body mounts:Mount front: FG 8418 Front bumperRear body mount: FG 7152/01 Rear body mountSide body mount front: FG 3014 Body mountsSide body mount rear: FG 3014 Body mountsDimensions:Length: 940 mmWidth: 415 mmHeight: 230 mmWheelbase: 530 mm Painting tips:
The Set contains the front body, the main body, the rear body, the spoiler-set and the body screws. The body shell is vac-formed from 2 mm Lexan.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 530/535 mm wheelbase. The set is delivered as shown.Required body mounts:Mount front: FG 7020/12 Front bumperRear body mount: FG 7152/01 Rear body mount Side body mount front: FG 7014 Body mountsSide body mount rear: FG 7014 Body mountsMeasures:Length: 890 mmWidth: 392 mmHeigth: 260 mmWheelbase: 530 mm
Genuine FG spare/option part. Fits on 2WD and 4WD touring car chassis' with 535 mm wheelbase, FG, Carson C5 chassis and most other 1/5 touring cars with the same wheelbase. The body shell is vac-formed from 2 mm Lexan.Clear for 1/5 scale for 530/535 mm wheelbase. With rear wing.Required body mounts:Mount front: FG 7020/15 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 8014 Body mounts Side body mount rear: FG 9014/01 Body mounts Contents:1 piece
Unfortunately, the pin striping lines on the body shell have not been applied very carefully and should be reworked individually, if you place value on it. The body shell is vac-formed from 2 mm Lexan.Measures:Length: 890 mmWidth: 392 mmHeight: 220 mmRequired body mounts:Mount front: FG 7020/16 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 8013 Body mounts Side body mount rear: FG 3014 Body mounts
The legendary sports car Bugatti EB 110 body shell for 1:5 on-road cars with standard chassis width and 530/535 mm wheelbase. The body shell is vac-formed from 2 mm Lexan.Dimensions:Total length approx. 870 mmTotal width approx. 380/385 mmTotal height approx. 220 mmRequired body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7154/01 Rear body mount Side body mount front: FG 8013 Body mounts Side body mount rear: FG 3014 Body mounts The body support FG 7154/01 is screwed directly onto the rear bridge. For attachment to the rear bridge, 2 holes 4 mm must be drilled in them.As a detailing kit (mirrors, windshield wipers!) set # 5435 is recommended (not included!).Since the Bugatti EB 110 1:5 scale body is - just like the original very low, a very low height air filter (#9043) is required. We also recommend 9.5 mm wide wheel squares: #6107 wheel squares 9.5 mm/M6 - 2pcs..For the body side support 32781.
Rare itemFord Capri Zakspeed RS 1/5 top quality body shell set, fits 1/5 touring cars with a wheelbase of 530mm.The body shell set includes main section, front air dam, rear section, rear wing and a pair of rear wing brackets with all necessary screws. The set is delivered with RS Zakspeed painted. Required body mounts: Rear side: 9014 FG Body mounts Front side: 3014 FG Body mounts Rear: 2x 7152/01 FG Extended rear mount Front pumper: 7020/14 FG Front bumper Front: 2x 7155 FG Body mount short adjustable Dimensions:Length: approx. 940 mmWidth front: approx. 390 mmWidth rear: approx. 415 mmHeight: approx. 230 mmContent:1 set
Genuine FG spare/option part.The body kit is supplied without rear spoiler! Required body mounts:Mount front: FG 7020/10 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 8013 Body mounts Side body mount rear: FG 7014 Body mounts Measures:Length: 900 mmWidth: 400 mmHeight: 245 mmWheelbase: 535 mmContents:1 piecePainting tips:
Genuine Samba spare/option part. The body shell is neither cut nor drilled, clear and can therefore be adopted to all touring cars with a 530/535 mm wheelbase.We have decided to make a new TC bodyshell to offer a new car from the WTTC series for the 5th scale drivers.Currently the most sought after large scale body shell with optimal aerodynamicsAvailable in 1 mm and 1,5 mm material thickness. The body shell consists of one part.Precut, the final cutting must be made according to the chassis you use it on.Width front / rear: 392 mm.Contents:1 piece
Rare itemFord Capri Zakspeed RS 1/5 top quality body shell set, fits 1/5 touring cars with a wheelbase of 530mm.The body shell set includes main section, front air dam, rear section, rear wing and a pair of rear wing brackets with all necessary screws. Required body mounts: Rear side: 9014 FG Body mounts Front side: 3014 FG Body mounts Rear: 2x 7152/01 FG Extended rear mount Front pumper: 7020/14 FG Front bumper Front: 2x 7155 FG Body mount short adjustable Dimensions:Length: approx. 940 mmWidth front: approx. 390 mmWidth rear: approx. 415 mmHeight: approx. 230 mmPlease note:You can find the matching decal sets in the shop's options menu! Content:1 set
Fits on 2WD touring car chassis' with 535 mm wheelbase, FG, Carson C5 chassis and most other 1/5 touring cars with the same wheelbase. The body shell is vac-formed from 2 mm Lexan.Due to the low body shell, you need the low height FG airbox # 9043.Clear body shell for 1/5 scale for 530/535 mm wheelbase. With rear wing and mirrows.Required body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 8013 Body mounts Side body mount rear: FG 3014 Body mounts Dimensions: Length: 900 mm Width: 395 mm Height: 230 mm Contents:1 piece Painting tips:
Genuine FG spare/option part. Audi RS5 DTM clear body shell for 1/5 cars with 530/535 mm wheelbase.The set includes main section and front air dam as well as the required special screws.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 530/535 mm wheelbase.Rear wing, side flaps/winglets and several decal sets are available from the options menu.The front section is also available separately as a spare part with part number y1441/01.This Audi RS5 DTM body shell is also available fully painted with either Team Audi Ultra (y1441/06) or Team Jägermeister (y1441/07) design.Required body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 3014 Body mounts Side body mount rear: FG 3014 Body mounts / for 4WD: FG 7014/02 Body mountContents:1 set
Genuine FG spare/option part. These bodyshells are mainly used for competitions. Therefore we deliver these body sets without rear spoiler. For competitions we recommend the CFK rear spoiler 245mm lightweight 8482/1, for the hobby driver the spoiler set 8047. The body shell is vac-formed from 1,5 mm Lexan.Required body mounts:Mount front: Rear body mount: Side body mount front: Side body mount rear: Measures:Length: 900 mmWidth: 400 mmHeight: 245 mmWheelbase: 535 mmEfra # 5053/06Contents:1 piecePainting tips:
y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.
Fits on all standard width touring car chassis' with 530 mm wheelbase, FG, Carson C5 chassis and most other 1/5 touring cars with the same wheelbase. The body shell is vac-formed from 2 mm Lexan. Replacement parts: 5192 FG Front Porsche 911 GTR3 R clear 5193 FG Rear Wing Porsche 911 GTR3 R clear Required body mounts:Mount front: FG 8418 Front bumperRear body mount: FG 7152/01 Rear body mountSide body mount front: FG 3014 Body mountsSide body mount rear: FG 3014 Body mountsDimensions:Length: 940 mmWidth: 415 mmHeight: 230 mmWheelbase: 530 mm Painting tips:
Genuine FG spare/option part. The alloy housing has an outside thread to adjust the damper spring. The upper alloy shock absorber seal is equipped with a ventilation boring which makes the refilling if the damper easier. Completely new is the lower shock absorber seal with the plastic guiding bushes for the damper piston rod and for an easier chaning of the o-rings. The alloy adjusting ring has a socket for the spring collet and an adjusting mark. The shock absorber has an diameter of approx. 16 mm. Suitable for all damper springs with approx. 17 mm inside diameter .With 110 mm hole distance.Contents:2 pieces
Fits on all standard width touring car chassis' with 530 mm wheelbase, FG, Carson C5 chassis and most other 1/5 touring cars with the same wheelbase. The body shell is vac-formed from 2 mm Lexan.Rear wing available in the options menue. Replacement parts: 5192 FG Front Porsche 911 GTR3 R clear 5193 FG Rear Wing Porsche 911 GTR3 R clear Required body mounts:Mount front: FG 8418 Front bumperRear body mount: FG 7152/01 Rear body mountSide body mount front: FG 3014 Body mountsSide body mount rear: FG 3014 Body mountsDimensions:Length: 940 mmWidth: 415 mmHeight: 230 mmWheelbase: 530 mm Painting tips:
Genuine Samba spare/option part. Our professional Carbon Rear Wing design with a wing profile, designed for our cars giving max pressure at the needed speed range.We use our special rear wing mounting structure also for this wing which makes the stability and the fixing of the wing easy.Very strong structure. No need for extra plates under the bodyshell.Weight: 60 gramContents:1 piece
€99.90*
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).