8182 FG Front body BMW M3 ALMS, transparente 2 mm

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

The new GRP tire XM1plus was produced to complement the GRP 2023 tire range because the vehicle set-up of the 1:5 RC cars showed that the grip between the compound difference of the XM1 and the XM2 proved to be a little too big.The addition of the GRP program with this new mixture of the XM1 plus, which consequently lies between the XM1 and XM2 in terms of grip, has shown that this often enables a more precise vehicle set-up and is particularly recommended for longer races, such as final runs.This pair of XM1plus tires has the following performance characteristics: HIGH GRIP for clean tracks. HIGH GRIP for medium to coarse asphalt grain. HIGH GRIP for medium to high temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!

The Set contains the front body, the main body, the rear body, the spoiler-set and the body screws. The body shell is vac-formed from 2 mm Lexan.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 530/535 mm wheelbase. The set is delivered as shown.Required body mounts:Mount front: FG 7020/12 Front bumperRear body mount: FG 7152/01 Rear body mount Side body mount front: FG 7014 Body mountsSide body mount rear: FG 7014 Body mountsMeasures:Length: 890 mmWidth: 392 mmHeigth: 260 mmWheelbase: 530 mm

Genuine FG spare/option part. Fits Audi A4 and BMW ALMS body shell.Not suitable for BMW M3 ALMS Superstar.Dimensions:Length: 107 mmWidth: 387 mmContents:1 piece

Hardened steel pinion set for Losi 5ive-T, 5ive-B and Mini, with corresponding engine mount inserts included. All parts with laser etched tooth count.Please note: The pinion do fit the 5ive-T 2.0 as well, of course. However, you then have to use the 5ive-T 2.0 engine mount inserts of the appropriate tooth count, inserts from the 5ive-T do not fit! Available with 16, 18T/20T/21T. The 19T pinion is stock equipment in Losi 5ive-T and Mini, 20T is stock in the 5ive-B.The 16T pinion is profile shifted and has the same dimensions as a normal 18T pinion.It is specially made for vehicles where the stock tires are replaced by much larger diameter rubber (i.e. monster truck tires and MadMax Giant Grip).Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter.SLO5T018T replaces LOSB5046 and LOSB5805SLO5T019T replaces LOSB5044 and LOSB5801SLO5T020T replaces LOSB5045 and LOSB5802The higher the tooth count, the higher the top speed!