7432/23 FG Steel gearwheel hardened 23 teeth - 1pce.

€30.70*

Available

Product number: fg_7432_23

EAN: 3410564518311

Product information "7432/23 FG Steel gearwheel hardened 23 teeth - 1pce."

Item N° 7432/23
Steel gearwheel hardened 23 teeth - 1pce.

Suitable for 39, 40 and 41 teeth main gear wheel.
Diameter 38.7 mm
Bore 10 mm
Total width 18 mm
Tooth width 11.5 mm
Module m=1.5

Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Alternatives

HT-Nitrited steel pinions for all FG and 1/5 scale Carson / Smartech C5

Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)Pinions up to 16T can be used on the layshaft as well.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Teeth:Item no.:13 Teeth HT y026814 Teeth FG 604614 to 48 Teeth HT y011615 to 48 Teeth FG 604715 to 48 Teeth HT y19354 wide16 to 48 Teeth FG 643116 to 48 Teeth FG 6431/1 wide17 to 48 Teeth HT y19355-116 to 46 Teeth HT y011917 to 46 Teeth HT y1935518 to 46 Teeth FG 643219 to 46 Teeth HT y1935718 to 44 Teeth HT y012319 to 44 Teeth FG 6432/220 to 44 Teeth FG 643321 to 44 Teeth HT y1935820 to 42 Teeth HT y090421 to 42 Teeth FG 7431/2122 to 42 Teeth FG 743121 to 40 Teeth FG 7432/2122 to 40 Teeth FG 7432/2223 to 40 Teeth FG 7432/2324 to 40 Teeth FG 743225 to 40 Teeth FG 7432/2526 to 40 Teeth HT y1936426 to 38 Teeth FG 7433Contents:1 piece

€29.90*

Configure now

HT-Alloy pinions for FG and Carson C5 / R5, 1 pce.

Hard coated surface for wear protection.Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€29.90*

Details

6433 FG Steel pinion 20 teeth - 1pce.

Item N° 6433 Steel pinion 20 teeth - 1pce.For combination with 44T main spur gear.Diameter 32.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

€35.90*

Customers also bought

7429 FG Plastic gearwheel 41 teeth - 1pce.

Suitable for all 1:5 models. With 63 mm diameter.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€17.90*

6431 FG Steel pinion 16 teeth

Genuine FG spare/option part.For combination with 48T main and differential spur gear.Diameter: 26.7 mmBore: 10 mmTotal width: 16 mmTooth width: 9.5 mmModule: m=1,5Contents:1 piece

€26.90*

7427 FG Plastic gearwheel 40 teeth

Genuine FG spare/option part.Suitable for all 1:5 models.Dimensions:Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Contents:1 piece

€17.90*

7432/22 FG Steel gearwheel hardened 22 teeth - 1pce.

Item N° 7432/22 Steel gearwheel hardened 22 teeth - 1pce.Suitable for 39, 40 and 41 teeth main gear wheel.Diameter 38.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€28.50*

- GWH05-XM3 GRP Slick W05 XM3 Tyres Hard

This pair of Tyres have the following use indications: VERY HIGH GRIP situation for very clean track. VERY HIGH GRIP situation for big asphalt. VERY HIGH GRIP situation for very high temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!

€38.90*

7186 FG Damper spring 2,7 mm black

Genuine FG spare/option part.Suitable for all FG shock absorbers and also for other makes with an outside diameter of 16 mm.Dimensions:Length: 58 mmOutside diameter: 20 mmWire diameter: 2,7 mmContents:2 pieces

€18.50*

Similar products

6431 FG Steel pinion 16 teeth

Genuine FG spare/option part.For combination with 48T main and differential spur gear.Diameter: 26.7 mmBore: 10 mmTotal width: 16 mmTooth width: 9.5 mmModule: m=1,5Contents:1 piece

€26.90*

7750 FG small module 1,25 transmission set, steel

Small steel modul (1,25) transmission set for Sportsline and Challenge Line, improves performance and reliability.

€119.90*

y0692 HT-Gearset for layshaft and differential fine pitch for 1/5 onroad

Genuine HT spare/option part.Fine pitch gears for layshaft and differential, for competition use in touring car and GT models only. The gears run smoother and quieter than the stock parts, reducing the car's rolling resistance.Module: m=1Fits FG and Smartech / Carson cars. Only for use as a set, not in combination with standard pitch gears!Contents:2 pieces

€79.90*

7431 FG Steel gearwheel hardened 22 teeth - 1pce.

Item N° 7431 Steel gearwheel hardened 22 teeth - 1pce.Suitable for 42 teeth main gear wheel.Diameter 35,7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€28.50*

7432 FG Steel gearwheel hardened 24 teeth - 1pce.

Item N° 7432 Steel gearwheel hardened 24 teeth - 1pce.Suitable for 39, 40 and 41 teeth main gear wheel.Diameter 38.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€31.90*

7432/25 FG Steel gearwheel hardened 25 teeth

Suitable for 39, 40 and 41 teeth main gear wheel.Measures:Diameter: 38,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11,5 mmModule: m=1.5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn't really matter.Content:1 piece

€35.10*

7433 FG Steel gearwheel hardened 26 teeth - 1pce.

Item N° 7433 Steel gearwheel hardened 26 teeth - 1pce.Suitable for 38 teeth main gear wheel.Diameter 41.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€29.90*

66217/01 FG Steel pinion 15T narrow, 1pce.

Item N° 66217/01 Steel pinion 15T narrow, 1pce.Layshaft pinion for FG 4WD cars, 10 mm bore diameter.Module: m=1,5

€29.95*

y19357 nitrided hardened Steel pinion with 19 to 46 teeth

Nitrided hardened, highly wear-resistant.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)For use on the clutch bell of FG cars in combination with a 46t spur gear on the layshaft. Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Contents:1 piece

€29.90*

HT-Nitrited steel pinions for all FG and 1/5 scale Carson / Smartech C5

€29.90*

Configure now

6432/17 FG Steel gearwheel 17 teeth, profile displaced, 1 pce.

Item N° 6432/17 Steel gearwheel 17 teeth, profile displaced, 1 pce. True running steel pinion for minimized wear. Suitable for all FG cars except Formula 1. Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn't really matter.

€33.90*

y0693 Extreme-Duty spur gear for FG, Smartech / Carson Offroad 2WD

y0693 Teeth: 13 teeth for offroad

Genuine HT spare/option part.Extreme duty gears for largescale offroaders and monster trucks. Set of coarse pitch pinion for the layshaft and corresponding differential spur gear, especially for use in off-road and monster models. The teeth are stronger and , due to their bigger size, a little bit more forgiving when the gear mesh is not adjusted correctly.Module: m=1,75To keep the original gearing the set is available with 12 teeth pinion for Monster Truck & Co. or 13 teeth pinion for all other off-roaders with standard sized tires.The differential spur gear has 41 teeth. Please tell us your choice!Fits FG 2WD cars and Carson Attack/Firehammer/Smartech Traveller, Carson Comanche, Touareg a.s.o. The gears have diameters like standard units.Contents:2 pieces [INCLUDE]profilverschoben[ENDINCLUDE]

€79.90*