HT-Alloy pinions for FG and Carson C5 / R5, 1 pce.

Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)Pinions up to 16T can be used on the layshaft as well.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Teeth:Item no.:13 Teeth HT y026814 Teeth FG 604614 to 48 Teeth HT y011615 to 48 Teeth FG 604715 to 48 Teeth HT y19354 wide16 to 48 Teeth FG 643116 to 48 Teeth FG 6431/1 wide17 to 48 Teeth HT y19355-116 to 46 Teeth HT y011917 to 46 Teeth HT y1935518 to 46 Teeth FG 643219 to 46 Teeth HT y1935718 to 44 Teeth HT y012319 to 44 Teeth FG 6432/220 to 44 Teeth FG 643321 to 44 Teeth HT y1935820 to 42 Teeth HT y090421 to 42 Teeth FG 7431/2122 to 42 Teeth FG 743121 to 40 Teeth FG 7432/2122 to 40 Teeth FG 7432/2223 to 40 Teeth FG 7432/2324 to 40 Teeth FG 743225 to 40 Teeth FG 7432/2526 to 40 Teeth HT y1936426 to 38 Teeth FG 7433Contents:1 piece

Hard coated surface for wear protection.Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

Layshaft pinion 16T for Carson / Smartech 2WD cars.Module: m=1,5

Genuine Speed-Tec spare/option part. Due to the air boxes mandatory for racing and the required off-road air filters, a strong and rigid insulator is a must! No more stripped threads, no warpage and the resulting air leaks at the insulator anymore! So many weird running behaviors, for example if the engine is warmed up and a tiny gap occurred at the insulator, are caused by this distortion of a plastic insulator. The increased heat transfer of the aluminum is taken into account by addition of an insulator plate. Therefore the aluminum intake is largely insulated. Due to the face-milled surfaces of the aluminum intake you reach a greater durability of the gaskets. The SPEED TEC aluminum insulator is available with two insulator plates.y1354/01 SPEED TEC cross aluminum insulator with 7 mm insulator plate and therefore a longer intake path for more torque. Ideal for off-road and cars. y1354/02 SPEED TEC Race aluminum insulator with 4 mm insulator plate, better for maximum rpm and therefore best for on-road use! Dimensions: Height of aluminum intake 20 mmHeight of cross version insulator plate - 7mm Height of Race version insulator plate - 3 mm Contents:Aluminum intake insulator plate 3 x gasket 2 x allen screw 5 x 30 mm 2 x washer 5/9.8 mm

Item N° 6433 Steel pinion 20 teeth - 1pce.For combination with 44T main spur gear.Diameter 32.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5