6447 FG Damper spring red 2,8mm - 2 pce.
€13.10
% €13.90 (5.76% saved)
Available
Product information "6447 FG Damper spring red 2,8mm - 2 pce."
Inner diameter 20.2 mm
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Customers also bought
Fits FG and Smartech touring cars. The use of steel spur gears on the layshaft increases reliability significantly. Pebbles, heat and shock loads created by high rev clutches are no longer a problem. The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of pinion and spur gear carrier are pointing to the outside of the car. The carrier features M8 grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution. The spur gears feature the same diameter as the FG plastic versions. The use of a steel clutch pinion is mandatory with steel spur gears! The spur gears are available as 39T, 40T or 41T versions. The following measures are required for installation of the HT-steel gear adapter "on-road" on the layshaft in FG EVO 2020 cars:- The installed wide 16T layshaft pinion 6431/01 must be replaced by the narrow version 6431.- The supplied 1mm shim must be added between layshaft pinion and ball bearing.- The flat sections on the layshaft do not have the usual 180° offset for the adapter; therefore only one grub screw will be used. However, since this is a wide face M8 version, this is no disadvantage.
Genuine FG spare/option part. Suitable for rc-plate 5014.Dimensions:Inside length: 44 mmInside width: 20,5 mmContents:2 pieces
Genuine FG spare/option part. Spare part for: 7331.Contents:1 piece
Item N° 07331/02Silencer Leopard RTR, 1 pce.Spare part for Sportsline Leopard 4WD.
Top quality epoxy P-R-M Race brake discs with 10 dirt slots for removing dirt and abrasion, which will be transferred to the outside by the discs rotation. The epoxy P-R-M Race brake disc provides an optimal deceleration of the car without the unwanted fading (poor braking performance due to increased heat buildup)! The best braking action when using the epoxy P-R-M Race brake disc is achieved by the combination of the epoxy brake discs and steel brake pads (8456 or y19218). The epoxy P-R-M Race brake discs fit mechanical front and rear brakes on FG / Smartech / Carson cars with brake pads 8456 recommended for these applications.1 pair (2 pieces) Dimensions: Outer diameter: 60 mm Thickness: 2 mmsocket for 18 mm square wheel drive
Item N° 6534/02 Throttle pivot post 3.1mm - setRevised set for 2 mm linkages, but with 3.1 mm pivot bore to prevent linkage seizing. Can be used for throttle or brake applications.Set collars have 2.1 mm inner diameter.
Customers also viewed
Completely mounted, with a 26 cm³ combustion engine and final speed of almost 100 km per hour, what else would you want?A further additional improvement is the installed front disk brake. A clear polycarbonate bodyshell is included.Quality and high-class equipment to a sensible price.Technical description of the Formula 1 Sportsline chassis:The undercarriage of the FG Formula 1 is built on a high-strength 5 mm alloy chassis. All chassis borings (screws) are countersunk. The front and rear axle with their various adjusting possibilities as king pin angle, trailing effect etc. consist of double delta wishbones. The double delta wishbones of the rear axle are supported by additional track rods which enable you a very fast set-up. All adjustments can be made without a dismounting of parts according to the fixed wishbone threaded rods with right-/left-handed thread.The model is equipped with 4 alloy oil-pressure shock absorbers. The push-rod suspension ensures the transmission between single wheel suspension and shock absorber.We deliver this chassis with a powerful 26 cc combustion engine. The engine's power is transmitted over a four-block Teflon clutch on a synchronous belt drive. This synchronous belt drive is also designed for a higher driving power. The BBS wheels and the tires are copies of the big models. All rotating parts are supported by ball bearings.The construction of the Formula 1 chassis is not identical with the other 1:5 scale FG models such as Merc. C-Class, Race Truck a.s.o. and therefore it can?t be converted into or from these models by a conversion kit.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 960 mmWidth: 440 mmHeight: 230 mmWheelbase: 620 mmFormular 1 models in action!
Shock absorber conversion kit for all 1:5 and 1:6 Ecoline models. Bulk oil-pressure shock absorber, experienced for years. Mounting hole distance: 113 mmTravel: 26 mmDiameter: 20 mmThe set contains 2 shock absorber with spring plate and spacer rings.
Genuine FG spare/option part. Fits all touring cars and Porsche 530.( Not for Mini Cooper und Porsche 465/510.)Contents:1 piece
Item N° 6534/02 Throttle pivot post 3.1mm - setRevised set for 2 mm linkages, but with 3.1 mm pivot bore to prevent linkage seizing. Can be used for throttle or brake applications.Set collars have 2.1 mm inner diameter.
Suitable for Formula 1.Length 48 mmInner diameter 17 mm
2,6 x 66,60 mmInner diameter 20.2 mm
Genuine FG spare/option part. Wheel / trigger type transmitter with ergonomic designRubber coated non-slip wheelLarge LCD display for easy settings10 model memoriesFHSS ModulationFailsafeDual rate on channels 1, 2 and 3Trims on the 3 channelsLow voltage (9,5V)7573/01 FG receiver 2,4 GHz fpr FG-RS3Contents:1 piece