6045/01 FG Brake shaft 97 with brake lever

€13.90*

Prices incl. VAT plus shipping costs

Available

Product number: fg_6045_01

EAN: 3410564505397

Product information "6045/01 FG Brake shaft 97 with brake lever"

Genuine FG spare/option part.

For single disc brake only.

Measures:

Length: 91 mm
Diameter: 6 mm
Thread: M3

Contents:

1 set

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

6038 FG Engine mount washers for M4 and M4 screws

Genuine FG spare/option part. Washers for the screws (M4 / M5) that hold the engine mounts to the chassis. Suitable for all FG models.Dimensions:Outside diameter: 15 mmInside diameter: 6 mmContents:4 pieces

€6.50*

6029/08 FG Ball-and-socket joint for M8

Genuine FG spare/option part. Reinforced plastic ball-and-socket joints for M8 thread rods. Replacement for the plastic ball-and-socket joints 6029/01.Fits 10 mm balls, total length 39 mm.Contents:4 pieces

€12.90*

6051 FG Dampening rubber

Genuine FG spare/option part. Rubber pucks for all standard design FG spur gear carriers.Dimensions:Outside diameter: 16 mmInner diameter: 7 mmHeight: 6 mmContents:4 pieces

€8.90*

6041 FG Steel layshaft 10 mm

Genuine FG spare/option part. For all FG models except Formula 1.Dimensions:Length: 103 mmDiameter: 10 mmImportant:When installed in a Carson / Smartech model the brake hub is fastened with a screw stomach.Content:1 piece

€21.90*

6029/07 FG Ball-and-socket joint for M6

Genuine FG spare/option part. Reinforced plastic ball-and-socket joints for M6 thread rods. Replacement for the plastic ball-and-socket joints 6029.Fits 10 mm balls, total length 39 mm.Contents:4 pieces

€12.90*

Details

6028/01 FG Track rod left/right 74mm for 1:6 models

Genuine FG spare/option part. Fits all FG 1/6 off road cars, alloy version.Length of threaded section approx. 17 mm.Contents:2 pieces

€13.90*

6050 FG Plastic gear carrier 60 mm

Genuine FG spare/option part. Plastic version, 60 mm diameter. For 48T - 46T spur gears.Also available in aluminum .Content:1 piece

€12.50*

6030 FG Steel ball 10x10,75 mm

Genuine FG spare/option part. Steel ball with 4 mm bore.Contents:4 pieces

€12.90*

6034/01 FG Plastic part for stiffening brace

Genuine FG spare/option part. Necessary for installation of 6034.Dimensions:Length: 35 mmDiameter thicker part: 10 mmDiameter thin part: 76 mmThread: M4Contents:2 pieces

€4.90*

6029/04 Ball-and-socket joint 10mm for M6 adjustable - 4pcs.

Plastic socket for 10mm balls, fits M6 rods, adjustable.For all FG cars.

€12.90*

6037/01 FG Steel mounting plate - 2pcs.

Item N° 6037/01 Steel mounting plate - 2pcs.Connects the large engine mount to the engine flange on all FG cars except evo 04 / evo 07 / competition 07Bulk:large extent plate:length: 35 mmwidth: 10 mmheight: 2 mmsmall extent plate:length: 25 mmwidth: 10 mmheight: 2 mm

€8.90*

6042/01 FG Brake square 97

Genuine FG spare/option part. Stock aluminum version for single disc brake.Also available in hardened steel.Dimensions:Height: 14 mmBore: 10 mmSquare: 18 mmContents:1 piece

€10.90*

Customers also viewed

4429/02 FG Steel taper disk 5mm bore

Genuine FG spare/option part.Steel taper disks, 3.5 mm thick, with a higher stiffness compared to alloy taper disks. Installation of these disks allows for larger operation angles of the metal ball joints and rose joints. You need two disks per joint.Contents:4 pieces

€10.95*

6427 FG Plastic gear wheel 46 teeth - 1pce.

46 teeth gear wheel for the layshaft.Diameter 72 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€37.90*

Spektrum SPM1452 optical RPM sensor

Genuine Spektrum spare/option part. Fits Spektrum DX3R Pro, DX3S and DX2S. Only working with a reciever with telemetry function like the "Spektrum SR3300T reciver".Content1 pieces

€12.99*

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€17.45*

6000c/2023 FG Marder Vintage-Classic with 26 ccm engine RTR

With complete RTR equipment y1382 Original Maxi-Pin 1/6 offroad competition tire The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder comes with completely installed remote control. Just fuel up, start the engine and drive off.Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm

€899.90* €969.95* (7.22% saved)