154100EB FG Sportsline 4WD Electro 530 Wheelbase, Basic, BLACK TUNED EDITION
Product number:
154100EB_bmw_m4.1
EAN:
4058575128366
Product information "154100EB FG Sportsline 4WD Electro 530 Wheelbase, Basic, BLACK TUNED EDITION"
Genuine FG spare/option part.
The following items are required for completion: electric motor, ESC, steering servo, radio system, body mounts, body, LiPo driving batteries and charger.
Incl.
The following items are required for completion: electric motor, ESC, steering servo, radio system, body mounts, body, LiPo driving batteries and charger.
Incl. 
Edition-Ausstattung
| Drive: | 4WD |
|---|---|
| Motorization: | Current |
| RTR: | Without RTR |
Login
Similar products
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece
Genuine HT spare/option part. After-Run is a performance enhancing preservation, which ensures that the engine starts properly, even after a long time (winter break) storage. Added to the fuel it keeps the fuel system clean.Among other After-Run conserves the diaphragm of the Walbro carburetor!For long term storage (i.e. during winter!) "vital" for the carburetor diaphragms!For 23 to 32 cm³ engines like Zenoah, Chung Yang, PT, Losi, HPI a.s.o.It binds water in the fuel, particularly important when the engine is not run regularly or after wet races. After-Run improves engine performance, ensures better combustion, removes debris and residues. Simply add the content of the bottle to 5 litres of fuel.Contents:1 piece / 20 ml
Content: 20 Milliliter (€395.00* / 1000 Milliliter)
Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!
Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.
The tire tread cutter is required for re-cutting worn-out or creating new tread designs in order to get more grip. Cutting depth is adjustable and cutting width is approx. 3 mm.Please note: This tool is designed for cutting model tires only, not for any fullsize vehicle tires!Content:1 pieces
If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price 85,80 EUR 105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter
Genuine HT spare/option part. Special fabric bag to protect engines, rc-plates or other expensive items. Large opening and pull-string closure.Size:Diameter 200 mmHeight 200 mmContents:1 pieceAccessories not included.
y0040 Variant:
y0040 Coupling member A and B
The secure hose connection for engine or tank removal! Advantages of the Kent system quick couplings: A safe opening and closing with one hand, as soon as one side is fixed. The design of the "shut-off" valve is a double chamber system, which closes when disconnecting the coupling. (This design enables easy and safe opening of the quick couplings, even under high pressure. Similarly, just as in low pressure applications.) You feel a snap when connecting the couplings, preventing over-tightening or accidental opening. The actions of opening and closing the quick couplings are identical, so that the handling is extremely simple. An ergonomic design guarantees easy handling, yet the space requirement for the couplings is low. Long and safe life of the couplings even with frequent connection and disconnection. In order to protect the fully encapsulated KENT quick coupling system against dirt even after dismantling, sealing the ends with the corresponding white plugs and caps is recommended.
Genuine Top Tuning spare/option part. Indispensable for optimal suspension tuning!Vacuum container for removal of bubbles from shock fluid when filling shocks.A vacuum pump is built into the lid. The tray has four holes each to accept 1/10, 1/8, 1/6 and 1/5 scale shocks.Suitable for shock absorbers from Losi, Mecatech, BWS, Arrma, Traxxas, FG, Carson, HPI and many more, as long as they have a suitable diameter. All shocks from 15 to 32 mm outer diameter can be used in the Bubble Ex to be "de-bubbled". Tray bore sizes: No. 1 = 32 mm diameter No. 2 = 21 mm diameter No. 3 = 17.5 mm diameter No. 4 = 15 mm diameter The maximum length of the shock absorber up to the upper edge of the body is about 150 mm, whereby longer shock absorbers can also be partially compressed for insertion. (e.g Losi 5ive-T and many more)Operation:Unlock the vacuum pump by turning it slightly to the left, the pump handle then extends a little. The small plug with handle is used to close and ventilate the container. To build up the vacuum, the plug must be in the down position.The small membrane on the opposite side serves as an indicator for whether a vacuum is present. Only when this is curved outwards the lid of the container can be opened again without any effort. Content: Can with integrated vacuum pump Shock tray
Off-Road tires mounted and glued on rims, on chrome rims. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Dimensions:Diameter: 150 mmWidth: 60 mmWheel square: 18 mmContents:4 pieces / 2 pairs
Unfortunately, the pin striping lines on the body shell have not been applied very carefully and should be reworked individually, if you place value on it. The body shell is vac-formed from 2 mm Lexan.Measures:Length: 890 mmWidth: 392 mmHeight: 220 mmRequired body mounts:Mount front: FG 7020/16 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 8013 Body mounts Side body mount rear: FG 3014 Body mounts
Customers also viewed
Genuine FG spare/option part. The following items are required for completion: electric motor, ESC, steering servo, radio system, body mounts, body, LiPo driving batteries and charger.
Incl. Edition-Ausstattung
Item No.:8181 Body BMW M3 ALMS, transparente 2 mm MAIN PART, 1 pce.Contains only the main body. If you need a complete body we advise .The main body is delivered not painted.
Genuine FG spare/option part. The following items are required for completion: body mounts, body, RTR (radio control, servos, batterie and charger).The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. The models are equipped with front disk brakes for an optimal braking power. Fully adjustable front and rear double wishbone suspensions.Further equipment points are : differential gear, central brake with oversized disk, oil-pressure shock absorbers with volume control and external adjusting ring for the initial tension of the spring. All rotating parts on ball bearings. The body parts are made of clear polycarbonate. Tires are glued on the rims. The models are driven by a 26ccm engine with a powerincreasing tuned pipe. The engine runs with a 2-stroke petrol-oil mixture. Through the installed pull-start system the engine can be started without any problem. The tank capacity enables you to run your model around 45 minutes.Not included : Radio system 2.4GHz Steering metal gear servo 25kg Gaz/Throttle servo 10kg Radio supplied with 8 stick battery and one chargerDimensions : Length 800 - 900 mm Width 392 mm Height ca.250 mm Wheelbase 530 mm Weight 10,2 kg
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece
Genuine FG spare/option part. The following items are required for completion: electric motor, ESC, steering servo, radio system, body mounts, body, LiPo driving batteries and charger.
Incl. Edition-Ausstattung
Inklusive 2x TT1530/650 5000 mAh LiPo Battery 6S Beast Edition: Standard equipment: Beast Edition: Motor: 780kV 650/620kV Regler: 160 A 250/300 A S-Power: 8S 12S
The Losi DBXL-E 2.0 is fitted with a Spektrum 780KV motor and a 160A Spektrum ESC as standard.With our 12S Beast Edition you can choose between 2 variants:1. Hobbywing Ezrun Max5 HV ESC 250A up to 12S LiPo BEC8 and Ezrun 650KV 4pol brushless motor, without surcharge.2. Hobbywing Ezrun Max4 HV ESC Sensorless 300A up to 12S LiPo, BEC 10A and Top Tuning Beast Brushless Motor 620KV 4pol, 190,00 € extra charge.
The original DBXL-E set the world on fire as the go-to vehicle for large scale bashers and enthusiasts alike. Its agile handling, out of the box speeds and durability make it a fan favorite. Now the Losi® DBXL-E 2.0 continues to build on the legendary status! Known worldwide for their dominance in the gas 1/5 market, especially with the 5IVE-T 2.0, Losi has built the DBXL-E 2.0 to be cleaner and easier to use, but with performance and speed that outruns the competition. At home in any environment from dirt to pavement, wet or dry, especially with its 4WD drivetrain with larger 5mm drive pins, the desert buggy makes sure all the power is put to the ground. Drivers stay in control with a DX3 transmitter, a Spektrum SR6100AT 6 Channel AVC® Telemetry Surface Receiver, and scale-to-size Maxxis Creepy Crawler LT tires. This desert buggy features all the technological advances drivers. Finally, the DBXL-E 2.0 has a Losi race-inspired motorsports themed livery for that true off-road look. You get all this and more from the brand that represents the pinnacle of performance.The Full-Throttle Freedom of AVC® TechnologyThe receiver's built-in AVC® (Active Vehicle Control®) traction control system works behind the scenes, making hundreds of throttle and steering adjustments per second, so more of the motor's power is translated into ballistic speed and acceleration instead of just flying dirt. The patent-pending AVC system adds a level of performance that simply cannot be found with any vehicle from any manufacturer other than Horizon Hobby. Like traction control in your full-scale vehicle, you can activate or deactivate the system on the fly and adjust the level of stability based on driving conditions. Any RC vehicle can go fast and with AVC you can go faster while maintaining optimum stability in all driving conditionFeatures
Without surcharge : Ezrun MAX5 HV G2 ESC 12S and Ezrun 650KV brushless engine.
Surcharge 190€ : Ezrun MAX4 HV G2 ESC and Top Tuning BEAST 620KV Brushless engine.
Spektrum DX3 radio system with AVC® and new SR6100AT Receiver Spektrum S906 1/5th scale metal gear servo Water protected components Aluminum Shock Towers Aluminum Center Diff Cup New Radio Tray designed for use with single or dual steering servos. New Heavy Duty Drivetrain with 5mm drive pins New Electric Chassis specific chassis braces for increased durability and strength Spedial motor adapter plate Modified ESC mounting bracket Beast decal sheet New ESC Mount Pinned Center Outdrive Cups New Gearboxes for improved drivetrain strength and stability New Steering Rack with helical servo saver design Updated Front and Rear Bulkheads Maxxis Creepy Crawler LT Tires Losi and Fox Shox race-inspired Motorsports themed livery Laser Etched FOX Logo Shock Caps Roof-mounted LED bar Dimensions Height: 317 mm Length: 844 mm Width: 495 mm Weight: 9,8 kg
Genuine FG spare/option part. Fits on all standard width touring car chassis' with 535 mm wheelbase, FG, Carson C5 chassis and most other 1/5 touring cars with the same wheelbase. The body shell is vac-formed from 2 mm Lexan. The vehicle decal sheet can be purchased separately in our shop selection.Required body mounts:Mount front: FG 7020/16Rear body mount: FG 7152/01 Rear body mountSide body mount front: FG 3014 Body mountsSide body mount rear: FG 3014 Body mountsFront body: 4171 FG Front body Audi R8 clearRear wing: 4172 FG Rear wing Audi R8 clearVehicle decals: 4173/01 FG Vehicle decals Audi R8 LMSDimensions:Length: 920 mmWidth: 385 mmHeight: 220 mmWheelbase: 535 mmContents:1 set