1171 FG rear ball stabilizer 4mm , Evo 07-08
€64.95
Currently unavailable
Product information "1171 FG rear ball stabilizer 4mm , Evo 07-08"
Only suitable for evo wishbones with 6 mm long hole. Series built on Evo 07 models.
Contents:
- 1 set
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Accessories / Spare parts
Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g
Content: 30 Gramm (€830.00 / 1000 Gramm)
Customers also bought
Original TopTuning spare/option part. Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT-Smartech/Carson engines.Fits all Walbro 603/813/990/771/527/1107 carburetors as well as all Smartech/Carson PT engine carburetors and many more!The TopTuning carburetor heat sink counteracts the notorious vapor lock at high engine temperatures.In fact all current large scale engines have a special adaptor for the thermal insulation of the carb (isolator) to keep the carb as cool as possible, so that the fuel does not form bubbles due to heat transfer from the cylinder. And without this isolator the gasoline would literally cook after a short operating time and therefore the engine would receive a leaner mixture. The much feared lean-out until the engine stalls is inevitably.Unfortunately, even a special isolator is often insufficient at higher ambient temperatures or when the engine is subjected to higher loads, e.g. in racing. In such scenarios the better heat dissipation of the Top Tuning carburetor heat sink contributes to the solution of the problem.The easy to install heat sink, requires a considerable manufacturing and milling effort and fits easily to all common 1:5/1:6 large scale cars, such as FG, Mecatech, Smartech/Carson, HPI, Losi, etc..For installation in FG 4WD cars the rear cross member # 66212 must be modified.Attention: the Allen head screw is an imperial size and therefore not compatible with metric Allen wrenches! Available in our options menu Content: Carburetor heat sink 1 x Allen head screw #8-32 x 5/8" (for Walbro carbs) 1 x washer 4 mm
Genuine FG spare/option part.Spare part for order no: 8380.Contents:1 set
Genuine FG spare/option part.Steel taper disks, 3.5 mm thick, with a higher stiffness compared to alloy taper disks. Installation of these disks allows for larger operation angles of the metal ball joints and rose joints. You need two disks per joint.Contents:4 pieces
Genuine FG spare/option part. Made from T7075 aluminum with wide epoxy insulator plates to protect against engine heat transfer. Venturi-shaped bore increases engine performance.For easier installation removing the cylinder shroud is recommended .Contents:1 Set
GPM air filter cover which fits easily over your existing air filter. A rubber band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments. Fits all common filters, foam or fabric (K&N) style.
Customers also viewed
Genuine FG spare/option part.4mm stabilizer bar.Stiffness can be adjusted by relocating of the inner clamping devices.Suitable for all FG Evo 04 and in connection with their rear lower wishbones (l/h version 1072, r/h version 1073) in FG touring cars with narrow rear axle too. Except Racetrucks, GT models and sport cars.
Genuine spare/option part.5mm stabilizer for the 2-damper front axle, not adjustable. Not suitable for Ecoline and Mono-Shock front axle.Contents:1 piece
Genuine FG spare/option part. Suitable for all 1:5 models, Race-Trucks and Monster models to optimize the road performance.Contents:1 set
Genuine FG spare/option part. Contents:1 piece
