Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

050024 Carson Fuelie standart clutch complete set

Product information "050024 Carson Fuelie standart clutch complete set"

Genuine Carson spare/option part.

Fits all Zenoah and Chung Yang engines.

Contents:
  • 1 set

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Similar products

Average rating of 0 out of 5 stars

y1419 Sintered steel clutch for Zenoah and many other engines from 23 cm³ to 32 cm³
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!

€19.00*

Average rating of 0 out of 5 stars

7317/11 FG Clutch spring reinforced 2,7mm G230/260/240/270/290/320
Genuine FG spare/option part. Fits Zenoah G230/260/240/270/290/320.Reinforced clutch spring for the Zenoah standard clutch. Engagement speed approx. 8000rpm. The engine has a higher torque and therefore more power for acceleration according to the raised operative speed. Suitable for all Zenoah engines.Contents:1 piece

€9.90*

Average rating of 0 out of 5 stars

7316/09, FG OEM clutch complete, set for Zenoah/CY/Fuelie/Losi engines
Complete clutch with spring, carrier and bolts. For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.

€44.90*

Average rating of 0 out of 5 stars

y1419/01 Clutch spring 6.000 1 / min for the Sintered clutch for Zenoah, Chung Yang, Losi, HPI & Co.
Clutch spring for about 6,000 1 / min. for the OEM clutches from Zenoah and many other rc-car engines from 23 cm³ - 32 cm³.Content:1 piece

€5.90*

Average rating of 0 out of 5 stars

7316 FG Clutch blocks for Zenoah
Genuine FG spare/option part. Zenoah bolts 7318 are required for installation.Content:2 pieces

€27.90*

Average rating of 0 out of 5 stars

7318 FG Dowel screw set for clutch blocks Zenoah
Genuine FG spare/option part. Part is delivered in silver or black color from vendor!Content:2 pieces

€9.90*

Average rating of 0 out of 5 stars

7317/08 FG Clutch spring for CY / Zenoah
Genuine FG spare/option part.Contents:1 piece

€5.90*

Average rating of 0 out of 5 stars

7315 FG Clutch block carrier Zenoah
Genuine FG spare/option part. Content:1 piece

€11.50*

Average rating of 0 out of 5 stars

67350 FG Tuning clutch / Zenoah, set
Item N° 67350 Tuning clutch / Zenoah, setComplete clutch with Tuning carrier, lighter clutch blocks, coated dowel screws and reinforced clutch spring. According to the lighter weight the engine speed is slightly higher when the clutch comes, therefore the engine has more power speeding up.

€59.95*

Average rating of 0 out of 5 stars

y0733 Big Scale-EXTREME, adjustable 3 - shoe clutch
With the Big Scale-EXTREME an adjustable clutch for very special requirements has been designed:For large-displacement enginesFor heavy or high traction cars (Losi, HPI)For modified performance enginesFor the demanding off-road useRapid wear of a clutch is a sign of constant slipping, even beyond engagement speed. In this case, the clutch does not transfer the applied torque.This is where the Big ScaleEXTREME sets a new standard.The new design of the "Extreme" prevents the centrifugal forces of clutch springs or lever side of the clutch shoes from counteracting the centrifugal force of the friction pad side even after engagement.As a result this clutch can transfer lots of power with minimal wear.The new design ensures that the centrifugal forces are transferred in full to the clutch lining. Precise engagement and disengagement even under high loads and inside of closed clutch bell carriers means no problem for this clutch.The clutch can be easily adjusted to the engagement speed through three set screws without clutch bell removal, so you can match the characteristics of your engine.The special clutch lining of the Big Scale-EXTREME is particularly wear-resistant and - especially in combination with a high-quality nitrited clutch bell (), guarantees for an exceptionally long service life! Contrary to the "Cross" or "Race" version there's no need to uninstall the clutch from the engine for maintenance. All parts are easily accessible from the front after removing the front plate.Please see the specifications tab for further information and handling advices!The regular price of the Big Scale-EXTREME is EUR 139.90

€149.90*

Average rating of 0 out of 5 stars

7316/01 FG Tuning-clutch block for Zenoah
Genuine FG spare/option part. Spare part for Zenoah ZG22, G230RC, G230RC 04 and G260RC.Zenoah bolts 7318 are required for installation.Contents:2 pieces

€39.80*

Average rating of 0 out of 5 stars

y0723 Gas-nitrited tuning clutch bell for FG, Smartech/Carson, Harm, RS5 & Co.
Genuine HT spare/option part. Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.Contents:1 piece

€49.90*

Customers also viewed

Average rating of 0 out of 5 stars

LOSB5044 Losi 19T Pinion Gear, 1.5M & Hardware 5T, TLR 5ive-B and Mini WRC
Genuine Losi spare/option part.Fits Losi 5ive-T, TLR 5ive-B and 5ive Mini WRC.Dimensionally identical with B55029Contents:1 piece

€29.99*

Average rating of 0 out of 5 stars

LOSR 8020 Tuned Exhaust Pipe, for 23-30cc Gas Engines 5ive-T/2.0 and Mini
The Losi LOSR8020 tuned pipe is dollar-for-dollar the easiest and cheapest performance upgrade you can buy for your 5ive-T/Mini. This complete exhaust system uses advanced two-stroke tuning technology to dramatically increase the low and mid range power and throttle response allowing any common 23-31cc engine to reach peak RPMs much quicker. The development was done over hundreds of laps and many hours by the Losi development team with the help of one the premier 1/5 scale engine/pipe builders. This design features a separate conical header and an ultra smooth tooled expansion chamber with a telescoping fit for both reliability as well as performance. The use of advanced precise tooling to produce both the header and the pipe optimizes the shock wave effect of the expansion chamber system as well as maximizing the durability. The hi-quality steel alloy is coated with a rust and heat resistant black finish for added protection and appearance. The compact design offers plenty of room for access to chassis parts and, since the pipe bolts directly and securely to the engine, gear changes and service on the clutch or engine is extremely easy. All mounting hardware, exhaust gasket and coupler are included as well as being available separately.Attention:Contrary to all other pipes from our range, this tuned pipe system has no silencer! Therefore it is very noisy and not allowed on most every official race track!FeaturesSeparate conical header and an ultra smooth tooled expansion chamberConstructed of hi-quality steel alloy and is coated with a rust and heat resistant black finish for added protection and appearanceRace inspired exhaust provides increase in power and performanceCreates a Racer like exhaust tone which is thrilling for the user as well as the spectatorImproves performance and provides powerful exhaust note

€229.99*

Average rating of 0 out of 5 stars

TLR356000 TLR Tuned Exhaust Pipe 23-32cc Gas Engines, 5B
Genuine TLR spare/option part.Contents:1 set

€199.99*

Average rating of 0 out of 5 stars

Fully assembled alloy diff incl. reinforced diff. tube and bevel diff. gearwheel for FG 2WD/4WD + Carson/Smartech 2WD
y0570 Typ: y0571 For Carson cars
Genuine HT spare/option part. Fully assembled Alloy differential including reinforced differential-tube and "inner-workings", such as original planetary gears, differential bevel gears, bevel differential wheel axles, sealed bearings, differential shafts with needle bearings (high-speed needle bearing).You only have to insert your full-floating axle (halfshafts). Since the FG and Carson are having different internal teeths by the planetary gears, different versions for FG and Carson/Smartech 2WD are available.Even on heavy off-road use and especially on jumps there are often problems with the original plastic differential. Noticeable is also the relatively thin differential-tube of the serial-equipping. Therefore our special offer for the complete Alloy differential including extra reinforced differential-tube.Set includet:8486 Alloy differential housing6068 Bevel differential gear axle6066/01 Differential bevel gear A, spline drive 6067 Differential bevel gear BFG ball bearings, sealed, y19610-rsReinforced differential tube for FG buggy differential, y09028498/01 Needle bearing for alloy differentialContents:1 set

€189.90*

Average rating of 0 out of 5 stars

Ball bearings for FG, sealed, diverse sizes
lager_0003 Size: y19608-rs For clutch bell, 2 pieces+ 4.3EUR
Genuine HT spare/option part. Dimensions:Alloy differentials 15 x 28 x 7 mmPlastic differentials 12 x 28 x 8 mmClutch bell(except standard Formula 1) 10 x 22 x 6 mmLayshaft 10 x 19 x 7 mm Wheel bearing 8 x 22 x 7 mmContents:1 pair / 2 pieces

Variants from €10.70*
€15.00*

Average rating of 0 out of 5 stars

5446/01 Mielke Clutch shoes aluminum for Power Gearshift clutches, set of 3
Genuine Mielke spare/option part.Clutch shoes for Mielke Power Gearshift clutches part numbers 5440, 5441 and 5442.Content:3 Pieces

€44.90*

Average rating of 0 out of 5 stars

y0358 Riot Pipe 3-chamber tuned pipe system for Carson Wild GP Attack and HPI Baja buggies
Chromed three-chamber tuned pipe system for Carson Wild GP Attack and HPI Baja buggies from the Australian exhaust manufacturer Powerslide Racing. Theres no need for cutting the stock Baja body shell for installation! Unlike many tuned pipe systems which are mounted in the rear of the Carson Wild GP Attack and HPI Baja cars and compromise power output due to the restricted available mounting space, the side mounting of the Riot Stampede allows for an optimized three-chamber system.You can see the Riot Stampede's multi-chamber design in the cutaway model shown in picture 9. The mounting system of Riot Stampede is secured by a tension spring and also provides the necessary flexibility even for jumps. The side mount uses a chromed adapter which is securely bolted to the chassis frame of your car. Set includes: Chromed tuned pipe Header and mounting bracket Complete installation hardware, as well as tension spring and exhaust hose

€189.90*
Loading...
Upload in progress, please be patient ...
Shopware-Plugin Development Shopware-Agency