6029/07 FG Ball-and-socket joint for M6
€12.90
Available
Product information "6029/07 FG Ball-and-socket joint for M6"
Reinforced plastic ball-and-socket joints for M6 thread rods. Replacement for the plastic ball-and-socket joints 6029.
Fits 10 mm balls, total length 39 mm.
Contents:
- 4 pieces
Login
Alternatives
Steel ball joint 4 mm thread, 3 mm bore in ball, for servo saver/servo linkage.This version is for servo linkage.Sets available:One each with r/h and l/h thread
Steel ball joint 4 mm r/h, 3 mm bore in ball, for servo saver/servo linkage.This version is for servo linkage.Sets available:One x r/h thread
Steel ball joint 4 mm l/h thread, 3 mm bore in ball, for servo saver/servo linkage.This version is for servo linkage.Sets available:One x l/h thread
Customers also bought
Genuine FG spare/option part. Contents:2 pieces
Genuine FG spare/option part. Reinforced plastic ball-and-socket joints for M8 thread rods. Replacement for the plastic ball-and-socket joints 6029/01.Fits 10 mm balls, total length 39 mm.Contents:4 pieces
Genuine FG spare/option part. Fits all FG 1/6 off road cars, alloy version.Length of threaded section approx. 17 mm.Contents:2 pieces
Even though the blade will keep its edge for a long time, no cutting tool will last forever. Spare blades are available of course.Cutting width approx. 3 mmPack of 5
Genuine Champion spare/option part.The Champion spark plug means higher speed range, longer time of exposure andimproved starting function. Thread size M10 x 1 fits CY / Fuelie / PT / Zenoah G230/240/260/270/290 and otherSerienkerze vom Zenoah G230/240/260/270.The most widely used, qualitatively best spark plug for the model sport! Especially by the most 1/6 scale models the short ceramic body is indispensable, because otherwise on grounds of the heightened mounting position- the spark plug would protrude beyond the roll cage and therefore is extremely fragile by flashovers.Contents:1 piece
Customers also viewed
Genuine FG spare/option part. Contents:4 pieces
Steel ball for rear upright.5 mm bore diameter
Steel ball joint 4 mm thread, 3 mm bore in ball, for servo saver/servo linkage.This version is for servo linkage.Sets available:One each with r/h and l/h thread
Ball-and-socket joint 10mm for M6. Can be used f.e. to lengthen the track rods.
Item N° 66244/01 Ball-and-socket joint 7mm f.M4, 30mm for Leopard 2WD/4WD, 8pcs.Spare part for the Leopard 2010 2WD/4WD version
To ensure the required cooling for current 1/5 and 1/6 engines the flywheels have fins on both sides. Therefore the fan housing has large openings on the crankcase side for the required air supply. However, the risk of foreign objects (grass, sand, or even stones!) entering here Is very high! As a result, broken fins on the flywheel occur frequently. This leads to reduced cooling efficiency and - even more critical vibrations from a flywheel which is out of balance due to missing fins. Therefore, this kind of flywheel protection is highly recommended, especially for offroad use. The product video explains the handling in detail! Note:It is essential to thoroughly clean and degrease the crankcase prior to attaching the hook-and-loop tape (OKS2661)!For installation on Chung-Yang and Zenoah engines in FG cars, the crankcase cover must be slightly modified in two places where the engine mount is attached (see Figure 6 and 7). Furthermore the fit of the fabric must be as tight as possible in the region of the layshaft pinion (in front of the differential ring gear!) (see Figure 8).Set includes:Special tailored fabric with sewed on hook-and-loop tapehook-and-loop tape for installation to the crankcaseAdhesive for securing the hook-and-loop tape