y0908 Rebuilt kit original Losi 5ive-T
€89.90
Available
Product information "y0908 Rebuilt kit original Losi 5ive-T"
The set includes the following parts:
- Cylinder
- piston
- piston ring
- cylinder foot gasket
- piston pin clip
Please note:
It is recommended to use a gasket sealer with every gasket on an engine.
This gives better sealing anda longer lasting gasket. We also recommend:
Nauenweg 55
47805 Krefeld
Germany
Login
Accessories / Spare parts
Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.
Content: 50 Milliliter (€538.00 / 1000 Milliliter)
Bindulin liquid rubber - very high elasticitySuitable for additional sealing of tuned pipes and exhaust / manifold connections .Temperature resistant from -60 ° to + 180 ° CResistant against diluted acids.Also for sealing threaded joints, electric lines and cable lead-throughs in receiver boxes.The surfaces must be clean, grease free and dry (brake cleaner).Contents:1 piece / 45 grams
Content: 45 Gramm (€331.11 / 1000 Gramm)
Product Safety DangerCauses serious eye irritation.Highly flammable liquid and vapour.May cause drowsiness or dizziness.Repeated exposure may cause skin dryness or cracking.Marston Universal blue is the leading non-setting gasket and sealing compound in use world-wide. The product is used by many of the world?s major automotive manufacturers and by several Formula 1 teams.Features- Non hardening and non setting- Unlimited assembly time- Vibration resistant- Allows metal to metal contact- Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants- Seals surface imperfections- Withstands rapid variations in temperature80 ml tube
Content: 80 Milliliter (€123.75 / 1000 Milliliter)
Genuine MD spare/option part. The red version with a temperature resistant up to 300°C. Directions for use:Clean the surfaces with a cleaner. Apply MD-Sil on one side and press the parts together. Touch-dry in 10 - 20 minutes. Curing speed 3 mm/24 hours. Contents:1 piece / 80 ml
Content: 80 Milliliter (€211.25 / 1000 Milliliter)
Customers also viewed
Cylinder-piston repair kit for 23 cm³ or 26 cm³ Losi 5ive-T engine. The set includes the following parts:Cylinderpistonpiston ringcylinder foot gasketpiston pin clipPlease note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Genuine Mielke spare/option part.Fits Mielke tuned pipe with the order number 5058.
With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-TWhen using an aluminum engine mount a stock length clutch housing is requiredSeparately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.
Cylinder-piston repair kit for Zenoah engine G230. Set includes the following parts:Cylinder, piston, piston ring, cylinder foot gasket, centering disks, piston pin clip.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Genuine FG spare/option part. Individual prices of the parts in the tuning set: 847,06 EurosAluminum conversion kit to aluminum front axle and aluminum rear knuckle and wishbone for FG Marder.Contents:1 set
Genuine Losi spare/option part. Contents:4 pieces