Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

y0811 After-Run, performance enhancing preservation for all 1/5 and 1/6th scale models, 20 ml

Product information "y0811 After-Run, performance enhancing preservation for all 1/5 and 1/6th scale models, 20 ml"

Genuine HT spare/option part.

After-Run is a performance enhancing preservation, which ensures that the engine starts properly, even after a long time (winter break) storage. Added to the fuel it keeps the fuel system clean.

Among other After-Run conserves the diaphragm of the Walbro carburetor!

For long term storage (i.e. during winter!) "vital" for the carburetor diaphragms!



For 23 to 32 cm³ engines like Zenoah, Chung Yang, PT, Losi, HPI a.s.o.

It binds water in the fuel, particularly important when the engine is not run regularly or after wet races.

After-Run improves engine performance, ensures better combustion, removes debris and residues. Simply add the content of the bottle to 5 litres of fuel.

Contents:
  • 1 piece / 20 ml

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

Average rating of 0 out of 5 stars

y1013 Motul Air filter oil for foam filters
Genuine Motul spare/option part. High-cling oil for foam cartridge air filters, especially for offroad and street use. The oil reinforces the the air filter'e efficiency and retains dirt, mud and sand particles, which will greatly extend the life of the engine. The blue tint makes it easier to control even oil application to the filter.Apply oil to filter generously and work the foam vigorously by hand to ensure complete oil penetration. Press foam slightly to remove excessive oil when done.Contents:1 piece / 400 ml

Content: 400 Milliliter (€47.25* / 1000 Milliliter)

€18.90*

Average rating of 0 out of 5 stars

y0994 Marston heat-proof sealer - 1pce.
Marston Universal blue is the leading non-setting gasket and sealing compound in use world-wide. The product is used by many of the world?s major automotive manufacturers and by several Formula 1 teams.Features- Non hardening and non setting- Unlimited assembly time- Vibration resistant- Allows metal to metal contact- Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants- Seals surface imperfections- Withstands rapid variations in temperature80 ml tube

Content: 80 Milliliter (€123.75* / 1000 Milliliter)

€9.90*

Average rating of 0 out of 5 stars

RC - Paint Lexan in 33 different colors spraycan (Offer) Buy 3 get 4
Genuine HT spare/option part.RC - Paint is a special paint for lacquering RC-Car Lexan (Polycarbonate) body shells. The ultra-fine mist provides optimal coverage! Through an optimized atomizer valve an outstanding painting result is guaranteed. The content of the can is 150ml and suffices - depending on the intensity of the painting, - for one 1/8 or two 1/10 body shells. Two to three cans are needed for a 1/5 or 1/6 body shell.RC-Paint Lexan color is produced in a particularly environmentally friendly. The composition of colors (color pigments) was placed on the lowest possible heavy metal content and the best possible environmental compatibility of the solvent and propellent gas value.Contents:1 piece / 150 mlPainting tips:

Content: 150 Milliliter (€66.33* / 1000 Milliliter)

€9.95*

Average rating of 0 out of 5 stars

04.0169 INNOTEC Power Clean metal and especially aluminum cleaner, 500 ml can
Special cleaner for aluminumPower Clean is a safe, fast-acting cleaner/degreaser for almost all types of contaminated metal parts and surfaces. The product removes brake dust, tar, undercoating, grease and various waxes and any type of contamination. Power Clean is a non-hazardous cleaner for electronic brake and ABS systems. Since the product does not attack the substrate, it is also particularly suitable for removing tar splashes and grease and oil stains.Power Clean evaporates completely without leaving any residue. Another major advantage is that the product does not cause white efflorescence on aluminum parts, as is the case with most brake cleaners. Thus, Power Clean is the perfect product for cleaning clutch and engine parts. The product comes out of the spray can at high pressure, making it easy to clean hard-to-reach places. In the spray can, Power Clean is particularly user-friendly and practical to use. Highlights .  span> harmless to aluminum. div>  span> High spray pressure, therefore suitable for heavily accessible places. div>  span> leaves no residues Content base: aliphatic hydrocarbons Density: 733 kg / m³ Consistency: liquid (firefitted in the aerosol can) viscosity: 2 mPa.s li> solvent: aliphatic hydrocarbons Flash point: 0 ° C Evaporation Residue: Maximum 4% Processing conditions: + 10 ° C to + 30 ° C SURFACES.Almost all types of metal, paints and plastics. Before use on plastics and paints, always test on an inconspicuous area. USAGESpray product on the parts to be cleaned and leave to act briefly. Re-spray to completely remove loosened dirt. Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging Storage conditions: Store in a cool, dry place Batch code type: F

Content: 500 Milliliter (€19.80* / 1000 Milliliter)

€9.90*

Average rating of 0 out of 5 stars

y19302/02 Piston Blocker for almost all engines
Genuine HT spare/option part. Helpful tool for removal of clutch shoes, flywheels and many more.FitsZenoah G230/G240/G260/G270/G290/G320Chung-Yang enginesPT enginesLosi enginesHPI enginesThreadsize:M10 x 1Contents:1 piece

€9.90*

Average rating of 0 out of 5 stars

y19302/01 Flywheel and Clutch puller CY, Zenoah, HPI, Losi
Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece

€17.90*

Similar products

Average rating of 0 out of 5 stars

y0781 Dry-Fluid Extreme especially for RC-Cars, 20 ml
Dry lubricant instead of oilWe did not think that today its still possible to make a real improvement in lubricants!DryFluid Extreme is especially designed for remote control model cars, with the aim to maintain the functionality and durability of these little racers as long as possible or to even extend significantly.The effect of the new lubricants for shafts, bearings, guides and ball joints starts where other lubricants reach their limits. Low friction, high lubricity and minimal attractivity to dust or dirt were the main developmental targets. Recent findings in aerospace and automotive technology as well as the experience of RC car drivers are the mentors of innovation of this new lubricant.What is DryFluid Extreme RC-Cars?DryFluid lubricant is more of a solid lubricant than a classic fluid one. DryFluid is not a wax, not oiling, non-greasy and free of silicones. The use of dry particles, polymer lubricants and high-end lubricating fluids results in a previously unknown lubricity without binding dust and dirt. Ease of application and long-term effects of DryFluid Extreme will delight any modeler.DryFluid Extreme product featuresReduces the power losses of shafts, bearings and ball joint systems and guarantees a long life of the treated componentsLowest friction for smooth operation and wear reductionMultistage lubricant system with immediate and long-term lubrication effectsDoes not bind any dust or dirtExtremely good penetrating abilityHighest compatibility with all common materials like metals, plastics and rubberExcellent adhesion and corrosion protection propertiesThe use of DryFluid Extreme RC-CarsThe main effect of DryFluid Extreme is the reduction of friction and wear on shafts, bearings, guides and ball joint systems. The dry components do not bind any dust or dirt and ensure best possible long term lubrication effects.For best results the parts to be treated should be thoroughly cleaned and the fluid applied sparingly. Repeated use increases the long-term effect.Before use, shake bottle vigorously for a short time!Nanotec lubricant for joints, shafts, bearings and gears of rc-cars. Excellent long term lubrication effects. Use included put-on canula for fine dosing. Let dry for several minutes after application and close bottle tightly. Shake well before use Attention:Keep out of reach of children. Do not swallow. Avoid contact with eyes. Keep away from ignition sources. Keep bottle closed tightly.

Content: 20 Milliliter (€845.00* / 1000 Milliliter)

€16.90*

Average rating of 0 out of 5 stars

y1434 VL32 Multi Oil Pen for RC-Car sport
Universal maintenance oil which has a high resistance to environmental influences; it is penetrating and moisture displacing with an excellent corrosion protection. Precise application is possible with the VL32 - Multipen's metal syringe tip. The ergonomic shape and rubberized handle provide a secure grip. Leakage of oil is prevented by the safety valve in the cap. Application: u> b>Pull off cap (avoiding strong pressure on the pen!), position the pen to the point of lubrication and press. Refit cap after use.Content:12 ml / 1 piece

Content: 12 Milliliter (€741.67* / 1000 Milliliter)

€8.90*

Average rating of 0 out of 5 stars

Chesterton 787 Sliding Paste, 50 ml
Wide neck flask with 50 ml.The "work of the devil!" The smell is normal! Among others this lubricant is suitable for the following model car applications:Drive shafts (if covered with boots)Transmission in enclosed housings (i.g. ring & pinion gears in Losi 5ive-T or Desert Buggy XL)Differentials which do not use friction padsChesterton® 787 Sliding Paste is a premium quality pure synthetic lubricant that will function effectively even at ultra high temperatures and pressures. Designed for the most severe operating conditions, it provides, through a novel chemical approach, lubrication at pressures up to 10687 kg/cm2 and 538°C.787 Sliding Paste is a unique thixotropic hybrid lubricant. Consisting of a semi-soft paste-like material, this product will flow to fill in small tolerances, yet will keep metal parts separated by the microscopic, symmetric, plates which slide over each other and provide effective lubrication long after the clean synthetic base oil has burned off. Applications for Chesterton 787 Sliding Paste can be found anywhere a need exists for a clinging semi-solid lubricant that will resist water washout and can withstand high temperatures and pressures. Unlike a grease which can turn to liquid and fail under extremely high loads and temperatures, 787 will maintain a slippery film on surfaces and prevent wear, galling and seizure at temperatures unthinkable for a grease. Use in such high temperature applications as lubrication of welding equipment, steel production facilities, smelting factories, forging furnaces, metal casting foundries, around exhaust stacks in power stations, turbine exhaust areas, and any other area exposed to extreme conditions. Because of its excellent resistance to water washout, the product works extremely well in outdoor applications such as on railroad switching equipment and wire rope cables.Composition:Chesterton 787 Sliding Paste is a unique hybrid material that suits the requirements of todays hotter running equipment. It consists of a combination of both organic and inorganic lubricating components and will perform effectively at temperatures ranging from -23°C to 538°C. The geometry of the solid constituents in 787 Sliding Paste is such that they slide over one another and remain undistorted even at the highest pressures parts and equipment are likely to see. The symmetry of the particles means they can withstand extra stresses compared to some inorganic materials which can shatter under extreme loads. The base oil used in Chesterton 787 Sliding Paste is a pure synthetic that will burn cleanly and leave no carbon or varnish to gum up parts and equipment. Because it contains no petroleum oils, it does not present the clean-up problems associated with waste petroleum residues.Features:Pure Non-Carbonizing, Synthetic Base n Lubricates at pressures to 10687 kg/cm n Withstands Temperatures to 538°CExcellent Water Washout Resistance n Non-Fling, Clinging LubricantLow Coefficient of FrictionNSF H2 - Registration number 133956 n No Toxic Heavy MetalsUltra-Fine ParticlesUnique 3 Phase Lubrication PackageApplications:Use in areas subject to extremes in temperature including smelting, forging, metal refining, glass manufacturing, plastics production, and in chemical, petrochemical and power plants, in foundries, around exhaust stacks, on rotary kilns in the cement and mining industry, etc. 787 is specifically designed to provide lubrication for surfaces subjected to extreme pressure. This would include wire ropes, cranes, railroad switch gear, and on large open gears on doors and bridges.Stem nuts, Lead screws, and Linear actuatorsFlange bolts and High tension studs n Press fit bushingsDirections:Brush or pump 787 Sliding Paste into areas needing to be lubricated. Product can be applied by squirt oiler. Spread evenly to thoroughly lubricate all parts and equipment which will see friction.Safety:Before using this product, please review the or appropriate safety data sheet for your area.

Content: 50 Milliliter (€258.00* / 1000 Milliliter)

€12.90*

Average rating of 0 out of 5 stars

OKS 2901 Belt tuning spray 400 ml, 1 pce.
The maintenance can for all cars with a belt drive.Clean, light-coloured film for increasing tensile strength and care of many kinds of belts.Increases tensile force by up to 50 % for all kinds of V-belts, round and flat belts. Protects against drying out and wear, prevents belt squeaking and slip.

Content: 400 Milliliter (€62.25* / 1000 Milliliter)

€24.90*

Average rating of 0 out of 5 stars

y0820 Robbe synthetic oil for plastic parts, 1 pce.
Special oil for plastics in precision applicator; following special advantages:- Friction reduced ten-fold- Completely smooth running- Wear reduced by 90%- Resistant to fuel attack and ageing- Does not attack plastic materials- Temperature range -30°C to 150°C Applications:- Bowden cables- Ball-links and joints- Plastic differentials- Transverse armcontent 4ml

Content: 4 Milliliter (€8,700.00* / 1000 Milliliter)

€34.80*

Average rating of 0 out of 5 stars

03.1104 INNOTEC PE100 silicone spray for plastic and rubber care, 500 ml can
Special plastic cleanerPE100 was specially developed to protect plastics from external agents. The product penetrates right into the molecular structure of the plastic,which is thus protected from the inside out, remains permanently supple and retains its natural gloss.Most RC cars have various axle parts, such as control arms and bearing blocks made of plastic. Due to weather influences and especially UV rays,or contact with tire conditioners can cause the plastic to become brittle and weather over time.Especially with unpainted plastic, this process progresses relatively quickly. PE100 slows down this process and provides intensive protection,which significantly extends the life of the plastic. Also, the likelihood of seals and protective rubbers (e.g. bellows for drive parts) becomingbecome brittle are much lower.In addition to this protective effect, PE100 gives the plastic parts a fresher appearance. PE100 is also excellent for protecting electronic parts frommoisture in electronic parts. Das Produkt bildet eine wasserverdrängende Schicht und verbessert somit den Korrosionsschutz.In the spray can, PE100 is particularly user-friendly and practical to use. Thanks to the special nozzle with tube supplied, even difficult-to-reach areas can be treated effortlessly. Highlights H3>  span> clear, almost invisible fluid div>  span> Easy application div>  span> displaces moisture div>  span> Long-term effect div>  span> protects plastics against discoloring div>  span> holds rubber parts supple and prevents them freeze div>  span> protects ignition systems from moisture-related disorders div> div>> CONTENTS base: silicone oils, mineral oils and additives Density: 710 kg / m³ Consistency: liquid (firefitted in the aerosol can) viscosity: ± 15 mPa.s li> Flash point: 0 ° C compressive strength: minimal li> temperature resistance: -20 ° C to> 150 ° C li> water resistance: good li> acid resistance: resistant to dilute acids li> corrosion protection: good. Corrosion protection results from the formation of a water-displaced layer. Inputs: good li> lubricant content: 17% li> Processing conditions: + 5 ° C to + 40 ° C Underground: Most plastics, rubber and metal USAGEPreparation of the substrate: Provide a clean, dry, grease-free and non-corroded substrate.Shake can well before use. When used as a lubricant, spray the product directly onto the part to be lubricated. When used as a plastic and rubber protector, spray the product directly (spray distance 15-20 cm) or apply with a cloth or sponge. To achieve a beautiful shine, briefly polish the plastic with a clean, dry Multi Wipe. Material cleaning: With Innotec Multisol or Innotec Power Clean Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging Storage conditions: Store in a cool, dry place Batch code type: F

Content: 500 Milliliter (€31.80* / 1000 Milliliter)

€15.90*

Average rating of 0 out of 5 stars

y0816 Motul Shine&Go
Genuine Motul spare/option part. Motul Shine&Go, a silicone based care for all metal and plastic parts. Protects the surfaces with a long term non-stick protective film, helping to prevent dirt, grime, tire rubber and dust from adhering. Once applied after cleaning the model, dirt can be removed much easier next time.Contents:1 piece

Content: 400 Milliliter (€32.25* / 1000 Milliliter)

€12.90*

Average rating of 0 out of 5 stars

03.1118 INNOTEC Multi Spray 1000, moisture displacing lubricant, 500 ml can
Moisture Displacing LubricantMulti Spray 1000 is a strong moisture displacing lubricant that loosens stuck parts and protects against corrosion. Multi Spray 1000 displaces moisture by penetrating between the substrate and water and then protecting the substrate like a protective film. The product is ideal for numerous applications in the RC hobby.It is ideal as a lubricant for bearing bushings, shafts, Bowden cables, etc., as well as for impregnating rubber. Multi Spray 1000 keeps rubber and plastic parts supple and smooth and protects plastic parts from weathering. Even already weathered plastic looks like new again due to the high penetrating power of the product. Multi Spray 1000 gives the plastic a natural shine in the process.Multi Spray 1000 cleans and protects tools, work surfaces, engines, sports equipment, boats, weapons, machines and stainless steel, copper or brass surfaces for a long time, but is also particularly suitable for electrical hand tools, switch boxes, power sockets, ignitions, batteries, spark plugs and electrical connections. These are often located in places exposed to weather, dirt, grease and road salt. Multi Spray 1000 has a protective effect, preventing corrosion.Multi Spray 1000 is one hundred percent silicone-free and therefore also an ideal working aid in repair shops and paint stores, or in any place where paints are processed industrially. All these properties make the product the perfect (light) lubricant, cleaner and protector for any work in the workshop. Multi Spray 1000 is available as a user-friendly spray can with extra nozzle and tube for those hard to reach places. HIGHLIGHTS. Loosens stuck parts and protects against corrosion. Keeps rubber and plastic supple and smooth Cleans and protects for a long time. Silicone free! Displaces moisture Ideal lubricant for locks, tools, cables etc.  Schützt elektrische Verbindungen auf sehr lange Daue  OEM-Genehmigung CONTENT base: mineral oil with special additives Density: 718 kg / m³ Consistency: liquid (ready to spray in the aerosol can) viscosity: 17.5 mPa.s (at 50 ° C) Flash point: 0 ° C compressive strength: minimal temperature resistance: -20 ° C to + 120 ° C water resistance: good against condensing moisture, moderately against sprayed water li> Acid Resistance: Good for sour haze, moderately against sour fluids no rust after 1000 hours (steel plates in relative humidity of 95%) no rust after 50 hours of salt spray test, starting rust after 100 hours Penetrating power: good Lubricant content: 25% Tests: Meets NSF requirements for category H2, registration number: 153349. Application conditions: -20°C to +40°C Substrate: All ferrous and non-ferrous metals, rubber and many plastics (except PMMA, PC, PTFE) USAGEPreparation of the substrate: Provide a clean, dry, grease-free and non-corroded substrate.Shake spray can well before use. When used as a lubricant, spray the product directly onto the part to be lubricated. When used as a plastic and rubber protector, spray the product directly (spray distance 15-20 cm) or apply with a cloth or sponge. To achieve a beautiful shine, briefly polish the plastic with a clean, dry Multi Wipe. Material cleaning: With Innotec Multisol or Innotec Power Clean Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging.

Content: 500 Milliliter (€29.80* / 1000 Milliliter)

€14.90*

Average rating of 0 out of 5 stars

WD-40 Smart Straw Multi function oil
With the integrated spray head can be changed between large-scale and precise spraying. The tube remains firmly at the spray head and is therefore no longer lost in the application. For surface spraying, the spray tube is simply folded down. With unfolded spray tube you can reach small spaces and can apply the product exactly accurately. Due to the 360 ​​° valve, the can can be maintained upright or overhead, so every application is possible.Protects against corrosion:Thanks to its corrosion-resistant formula, it offers long-lasting protection against rust and all forms of oxidation on metal surfaces.Temperature range: -50 to +150° C Eliminates squealEines der Hauptkomponenten ist ein aktives Schmiermittel, welches die Gängigkeit beweglicher Teile erleichtert und gleichzeitig Quietschen und Knarren beseitigt. Darüber hinaus schmiert es Teile und Mechanismen. Displaces moistureThe WD-40 multifunction product forms a perfect barrier against moisture by adding it. Thus, electrical and electronic mechanisms are always protected and creep currents are avoided. Cleans and protectsSolves stubborn dirt, oil, fat and adhesive residue and lets you easily remove. Leaves a nourishing protective layer. Loosens rusted partsLoosens stuck mechanics and jammed metal parts by infiltrating rust layers to loosen them. WD-40® multifunction product infiltrates and loosens rusted and fixed screws. It penetrates in hinges into the thread and protects against corrosion. WD-40® multifunction product displaces moisture, lubricating and eliminating squeaking. >PRODUCT PERFORMANCE AND FEATURES: Eliminates squeaks Undercuts moisture, resin, tar and dirt Cleans and protects against corrosion Loosens rusted parts Loosens stuck mechanics, rusted bolts and nuts Removes dirt and lubricates all types of tools Silicone, resin and PTFE free >MATERIAL COMPATIBILITY: GENERAL: Virtually all materials react to WD-40® Multifunction Product in the same way as they do to other high-quality aliphatic solution benzenes under the same conditions of exposure, such as spraying, short or even prolonged immersion. WD-40® multifunction product does not contain silicone, PTFE or chlorofluorocarbons. RUBBER: No visible effects on the surface of various types of rubber that have been sprayed with WD-40® Multifunction Product. Certain types of rubber swell when immersed in WD-40® Multifunction Product for extended periods of time. STRENGTHENED STEEL (for hydrogen embrittlement): Rated SAFE according to the Lawrence Hydrogen Effusion Test. FABRIC:WD-40® multi-function product causes no visible effect except slight discoloration that can be easily removed with naphtha or dry cleaning solvent (Tested: Nylon, Orlon, Wool, Dralon, Cotton). PAINTED SURFACES: Many types of paint on various surfaces have been exposed to WD-40® Multifunction Product without observing an effect. Wax polishes and certain wax coatings may be softened by WD-40® Multifunction Product. PLASTICS: Die folgenden Kunststoffe wurden 168 Stunden lang in WD-40® Multifunktionsprodukt eingetaucht ohne sichtbaren Effekt: The following plastics have been immersed in WD-40® Multifunction Product for 168 hours with no visible effect: polyethylene - Formica - epoxy - Delrin - polypropylene - acrylic - vinyl - polyester - nylon. Clear polycarbonate and polystyrene may develop hairline cracks or larger cracks when in contact with WD-40® multifunction product. > APPLICATION: Shake well before use. Hold can upright, tilted or upside down when spraying. IMPORTANT: Disconnect power from power tools, equipment and other live parts before spraying.

Content: 200 Milliliter (€39.90* / 1000 Milliliter)

€7.98*

Average rating of 0 out of 5 stars

WD-40 Contact spray
WD-40 SPECIALIST contact spray removes oil, dirt, flux and oxidation residues from sensitive electrical or electronic equipment. The product can be used on electrical equipment, contacts, plastic and rubber.Temperature application range: room temperatureApplication:First disconnect all plugs from equipment to avoid current and allow hot surfaces to cool. Shake the can before use and apply the spray directly on the surface to be treated at a distance of 15 to 20 cm. This will remove any residue that could interfere with electrical contact. Tilt the surface while cleaning and allow excess liquid to dry completely before restoring power. To avoid accidental damage, always check the manufacturer's instructions before applying the product to the equipment. Do not spray product into cavities, openings, crevices or areas of your device where it does not have sufficient airflow to support complete evaporation.Smart Straw - Product Benefits:The integrated spray head allows you to switch between large-area and precise spraying. In this case, the tube remains firmly attached to the spray head and is therefore no longer lost during application. For area spraying, the spray tube is simply folded down. With the spray tube folded out, you can reach small spaces and apply the product there with pinpoint accuracy. The 360° valve allows the can to be held upright or even overhead, making any application possible.WD-40® multifunctional product infiltrates and loosens rusted and stuck screws. It penetrates the threads of hinges and protects against corrosion. WD-40® multifunction product displaces moisture, lubricates and eliminates squeaks. > PRODUCT PERFORMANCE AND FEATURES: Smart Straw® Spray system for area and spot spraying Fast acting and non-conductive Perfect cleaning for electrical/electronic equipment, contacts, plastics or rubber Penetrates quickly without leaving residues Penetrates even the most difficult to reach areas K2 registered #145372 > AREAS OF APPLICATION: Electrical assembly Circuit boards Controls Printers & copiers Switches > USAGE: Shut off unit and allow hot surfaces to cool. Disconnect all plugs from unit to avoid power supply. Shake can before use. Apply spray directly to surface to be treated at a distance of 15 to 20cm to remove all residues that may interfere with electrical contact. Tilt surface during cleaning. Allow excess liquid to dry completely before restoring power. To avoid accidental damage, always check manufacturer's instructions before applying product to equipment. Do not spray into cavities, openings, crevices or areas of your equipment where this product does not have sufficient airflow to support complete evaporation. Tilt the surface during cleaning to allow excess liquid to drain and the product to dry completely before returning it to service and connecting it to the electrical circuit.

Content: 300 Milliliter (€33.27* / 1000 Milliliter)

€9.98*
%

Average rating of 0 out of 5 stars

y1596 INNOTEC Allround Complete Set
Genuine INNOTEC spare/option part. The RC-car all-round wellbeing set for cleaning, sealing and moisture displacement. Set contents: INNOTEC PE100 silicone spray for plastic and rubber care PE100 was specially developed to protect plastics from external agents. The product penetrates right into the molecular structure of the plastic, which is thus protected from the inside out, remains permanently supple and retains its natural gloss. Content 500 ml Can INNOTEC Multi Spray 1000, moisture displacing lubricant Multi Spray 1000 is a strong moisture displacing lubricant that loosens stuck parts and protects against corrosion. Multi Spray 1000 displaces moisture by penetrating between the substrate and water and then protecting the substrate like a protective film. The product is ideal for numerous applications in the RC hobby. Content 500 ml Can INNOTEC Adhesive remover and degreaser Seal and Bond Remover is a slow evaporating universal degreaser that is also perfect for quickly and efficiently removing all types of adhesive and sealant residue. The product softens most adhesives and sealants to make them easier to remove. Content 500 ml Can INNOTEC Power Clean Metall- und insbesondere Aluminium Reiniger Power Clean ist ein sicherer, schnell wirkender Reiniger/Entfetter für fast alle Arten verunreinigter Metallteile und -flächen. Das Produkt entfernt Bremsstaub, Teer, Unterbodenschutz, Fett und diverse Wachse und jede Art von Verschmutzung. Power Clean ist ein ungefährlicher Reiniger für elektronische Brems- und ABS-Systeme. Da das Produkt den Untergrund nicht angreift, eignet es sich auch besonders zum Entfernen von Teerspritzern sowie Fettund Ölflecken. Content 500 ml Can INNOTEC Multi Clean Universal foam cleaner for all plastic and metal parts on the RC car Multi Clean is a highly effective foam cleaner for countless types of dirt on almost all surfaces that can be easily applied to horizontal as well as vertical surfaces due to a stable active foam while intensively affecting the contaminants. Content 600 ml Can Set consists of:5 Dosen

€59.90* €76.90* (22.11% saved)

Average rating of 0 out of 5 stars

y0781/01 Dry-Fluid "Gear Lube" for gears, 10 ml
Dry lubricant instead of oil DryFluid Extreme Gear Lube is specifically designed for highly loaded gears in models. It is characterized by extreme pressure resistance and excellent adhesion. Through the use of solid lubricant components, it shows only a slight tendency for dust and dirt retention. Main applications of the newly developed Gear Lube Gear are of model helicopters, rc-cars and trucks, model trains and servos. Also ideally suited for shafts and gimbals of any kind.DryFluid lubricant is more of a solid lubricant than a classic fluid one. DryFluid is not a wax, not oiling, non-greasy and free of silicones. The use of dry particles, polymer lubricants and high-end lubricating fluids results in a previously unknown lubricity without binding dust and dirt. Especially the long-term effects of DryFluid Extreme will delight any modeler. Product characteristics at a glance: Exciting lubricating propertiesReduces power losses caused by friction Reduces operating noise Reduces wear Extremely pressure resistant Long-term stability Highest adhesion High material compatibility with metals, plastics and rubber materials Low tendency for dust and dirt binding Application Notes: A thin layer of the Gear Lube is enough for an extreme lubricating effect. If possible, apply to an upright standing gear and rotate it during the application. For hard to reach places and selective applications use the included canula. For fine and uniform distribution use a fine hair brush immediately after the application of Gear Lube. Transmissions that have not been treated with Gear Lube before should be thoroughly cleaned first. Shake well before using and apply sparingly!High End dry lubricant for highly loaded gears in models. Especially for transmissions of model helicopters, rc-cars, trucks, model trains and servos. Can also be used for shafts and gimbals of any kind Through the use of dry particles, lubricating polymers and high-end lubricating fluids an unprecedented lubricating effect is achieved. Extremely pressure-resistant and with excellent adhesion. Very low tendency for dust and dirt retention. Multistage dry lubricant system with long-term effects.

Content: 10 Milliliter (€1,690.00* / 1000 Milliliter)

€16.90*

Customers also viewed

Average rating of 0 out of 5 stars

04.0169 INNOTEC Power Clean metal and especially aluminum cleaner, 500 ml can
Special cleaner for aluminumPower Clean is a safe, fast-acting cleaner/degreaser for almost all types of contaminated metal parts and surfaces. The product removes brake dust, tar, undercoating, grease and various waxes and any type of contamination. Power Clean is a non-hazardous cleaner for electronic brake and ABS systems. Since the product does not attack the substrate, it is also particularly suitable for removing tar splashes and grease and oil stains.Power Clean evaporates completely without leaving any residue. Another major advantage is that the product does not cause white efflorescence on aluminum parts, as is the case with most brake cleaners. Thus, Power Clean is the perfect product for cleaning clutch and engine parts. The product comes out of the spray can at high pressure, making it easy to clean hard-to-reach places. In the spray can, Power Clean is particularly user-friendly and practical to use. Highlights .  span> harmless to aluminum. div>  span> High spray pressure, therefore suitable for heavily accessible places. div>  span> leaves no residues Content base: aliphatic hydrocarbons Density: 733 kg / m³ Consistency: liquid (firefitted in the aerosol can) viscosity: 2 mPa.s li> solvent: aliphatic hydrocarbons Flash point: 0 ° C Evaporation Residue: Maximum 4% Processing conditions: + 10 ° C to + 30 ° C SURFACES.Almost all types of metal, paints and plastics. Before use on plastics and paints, always test on an inconspicuous area. USAGESpray product on the parts to be cleaned and leave to act briefly. Re-spray to completely remove loosened dirt. Hand cleaning: With Innotec Power Scrubs or with Innotec Safe Hand Clean Plus and water Shelf life: 2 years in unopened original packaging Storage conditions: Store in a cool, dry place Batch code type: F

Content: 500 Milliliter (€19.80* / 1000 Milliliter)

€9.90*

Average rating of 0 out of 5 stars

y1434 VL32 Multi Oil Pen for RC-Car sport
Universal maintenance oil which has a high resistance to environmental influences; it is penetrating and moisture displacing with an excellent corrosion protection. Precise application is possible with the VL32 - Multipen's metal syringe tip. The ergonomic shape and rubberized handle provide a secure grip. Leakage of oil is prevented by the safety valve in the cap. Application: u> b>Pull off cap (avoiding strong pressure on the pen!), position the pen to the point of lubrication and press. Refit cap after use.Content:12 ml / 1 piece

Content: 12 Milliliter (€741.67* / 1000 Milliliter)

€8.90*

Average rating of 0 out of 5 stars

Mecatech FW01 Touring car, wheelbase 510 mm, Basic Kit -- Europe- and world champion
The Mecatech FW01 is for sure the currently most innovative 1/5 race car designed for the dedicated and technically enthusiastic rc car driver.Everyone is enthusiastic about the perfectly fitting and precise workmanship at the highest level. Only high quality materials are used for the production.Since many years Mecatech is a well-know premium manufacturer of largescale hydraulic brakes or shocks and, as only a few may know, a technology expert for a number of Formula 1 racing teams!The Basic Kit of the FW01 is especially intended for "switchers" and differs from the chassis kit in terms of the brakes and shock absorbers (included in the chassis kit). Here is a list of the parts that are required for completion:brakes, shocks and springs (Difference to Chassis Kit)DifferentialEngine Clutch, Airbox and tuned pipe systembody shell and tiresElectonic components such as servos, batteries and Remote controlStock gearing:Clutch pinion / spur gear: 36T / 64TLayshaft pinion / differential: 24T / 73TCurrently the Mecatech FW01 is for sure the benchmark of the 1/5 scale racing scene! In the first year Markus Feldmann won with his FW01 1: 5 Mecatech on one of the world's finest and most demanding race track in Lostallo / SwitzerlandMecatech is multiple German, European and World Champion with the FW01 and as the last result:Markus Feldman wins the European Championship in Tourlaville/France. All top 5 positions went to drivers running a Mecatech FW01. 7 out of 10 finalists cars were Mecatech FW01.Although the fit of the Mecatech FW01 parts makes the assembly of the car a great experience, some of our customers want to use the expertise of our shop and wish their FW01 fully assembled and tuned in by us!The complete assembly of your FW01 by our workshop is possible for an additional charge. Please note that the costs of the full assembly with servos a.s.o. do not include the price of any rc-components. If you do not have a suitable radio system with servos and batteries as well as switch and charger, you have to take an additional EUR 800 to EUR 1,500 for this equipment into account. We will be happy to make you an appropriate offer. We are currently waiting for the latest version of the Mecatech FW01.Included in the basic kit:- All pinions- clutch bell- Coupling fixation- All parts and screws for mounting the engineDoes not include- Brakes, shocks and springs- differential- clutch- body and spoilers- Airbox- Engine and linkage- Electronics- Tires

€1,862.00*
%

Average rating of 0 out of 5 stars

Original Zenoah engine to choose with carburetor and spark plug
y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

€259.90* €299.90* (13.34% saved)

Average rating of 0 out of 5 stars

y0994 Marston heat-proof sealer - 1pce.
Marston Universal blue is the leading non-setting gasket and sealing compound in use world-wide. The product is used by many of the world?s major automotive manufacturers and by several Formula 1 teams.Features- Non hardening and non setting- Unlimited assembly time- Vibration resistant- Allows metal to metal contact- Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants- Seals surface imperfections- Withstands rapid variations in temperature80 ml tube

Content: 80 Milliliter (€123.75* / 1000 Milliliter)

€9.90*

Average rating of 0 out of 5 stars

Challenge Line 2WD 530E Electric BMW 320 si incl. ESC + Motor
Genuine FG spare/option part. The FG Touring and Sports cars at scale 1:5 are known for their high quality and very detailed bodyshells true to original. Also the technically fully developed chassis are worth mentioning. These models are now available with a high-torque brushless engine. Surface conditions with maximum grip assumed speeds above 100 km/h can be reached and steered controlled. E stands for electric power which is equivalent to extremely high torque, high speed and all this without any engine noise. The Challenge Line models are equipped with a powerful 800 - 1300 kV brushless Motor and a 150A brushless ESC. This control can be regulated simply via transmitter or optionally via the program card.The models are built on a 4mm aluminium chassis with rear wheel drive and double wishbones front and rear. All borings are countersunk. Fully adjustable front and rear double wishbone suspensions.Further equipment points are: differential gear, oil-pressure shock absorbers with volume control and external, adjusting ring for the initial tension of the spring. All rotating parts on ball bearings.Tires are glued on the rims.For all versions of the electric cars, the LiPo batteries and the matching charger, as well as the radio system and the steering servo (RTR) are required. In our shop selection, the RTR set is available for a surcharge.For hassle-free assembly, FG recommends using LiPo batteries 2x 2S or 2x 3S, with a maximum dimensions of 150 mm in length and 50 mm in width. The model comes with the EC8 connector system equipped.

From €849.90*

Average rating of 0 out of 5 stars

y0813 Motul 800 Racing Oil
Fully synthetic oil, available in three blends. 1-liter bottle.The optimal 2-stroke oil for 23-30 cm³ engines/cars Motul Racing Oil is available in three different blends: On-Road for high revving onroad cars Off-Road for cars with high torque enginesMixing ratio for 1/5 & 1/6 applications: We recommend a mix with about 4% oil, which means 200 cc of oil to 5 litres of gas (1:25 ratio). With one litre of Motul oil you can mix about 25 litres of optimal fuel for your 1/5 or 1/6 car. That's enough for well over 20 hours of driving fun! Oil / Gas Oil percent Oil per 1 liter of gasoline Oil per 2 liter of gasoline Oil per 3 liter of gasoline Oil per 4 liter of gasoline Oil per 5 liter of gasoline 1:20 5% 50 ml 100 ml 150 ml 200 ml 250 ml 1:25 4% 40 ml 80 ml 120 ml 160 ml 200 ml 1:30 3,33% 33 ml 67 ml 100 ml 134 ml 167 ml 1:33 3% 30 ml 60 ml 90 ml 120 ml 150 ml 1:35 2,86% 29 ml 58 ml 86 ml 115 ml 143 ml 1:40 2,5% 25 ml 50 ml 75 ml 100 ml 125 ml 1:50 2% 20 ml 40 ml 60 ml 80 ml 100 ml

From €24.00*
Loading...
Upload in progress, please be patient ...
Shopware-Theme Development Shopware-Agency