y0463/02 Complete set of 28 sealed bearings for Losi 5ive-T 2.0

Genuine HT spare/option part. Alloy case conversion kit for Carson Gas Devil, Carson CRT 4x4, Conrad Hell Devil and Smartech Titan, can be used for the center differential onlyComes complete as shown with sealed bearings, installed needle bearings, shims, screws and o-rings, diff tube and the parts for the slip adjustment device.Adjustment of the locking effect:The adjusting screw which presses on the bevel gear axle and the thrust bearing regulates the locking. This causes friction between the bevel gear and the diff. housing. The locking effect can be adjusted between 0% and about 90%. The adjustment has to be changed according to track surface and dirt accumulation.Loosen the locking effect completely if the track is wet.Contents:1 piece

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, intake is flow-optimized the case is specially matched with enlarged and flow-optimized cross section towards the ports Crankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

Dimensionally identical with Losi 5ive part LOSB2543.Contents:2 piece

Genuine ATOP spare/option part.ATOP tie rod set with guide bushing set and with steel ball joints and turnbuckle center piece with locknuts for Losi 5ive-T.Balls with 6 mm bore diameter, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 134 mm.Contents:2 pieces

24-piece set of sealed 2RS ball bearings for Losi 5ive-T and Mini WRC. Set includes:4 pieces 10 x 15 x 4 mm (LOSB5970)4 pieces 9 x 20 x 6 mm (LOSB5974)4 pieces 12 x 24 x 6 mm (LOSB5972)6 pieces 15 x 24 x 5 mm (LOSB5973)2 pieces 15 x 28 x 7 mm (LOSB5975)4 pieces 20 x 32 x 7 mm (LOSB5971) Total of Losi prices for this 24-piece sealed bearings set when bought separately: 156.89 EUR

Genuine Top Tuning spare/option part.This kit includes all required parts for converting a Losi 5ive-T 2.0 into an electric car.Contents:TT1024 Top Tuning Electric conversion kit for Losi 5ive-T 2.0Genuine Top Tuning spare/option part.All aluminum parts are made of 7075 alloy.Front motor mount design to assure ample clearance for the rear brake disc when running mechanical brakes.Accepts two batteries up to 164 mm long und 50 mm wide. Rear motor clamps:Diameter 57 mm i.e. for Tenshock or CastleDiameter 57,8 mm i.e. for Leopard 58 lineDiameter 60 mm i.e. for LehnerDiameter 70 mm i.e. for BP70120 ZTW Beast Brushless engine 620 kVThis conversion kit is for the 5ive-T 2.0 only. It even allows for running the big BP70120 ZTW Beast Brushless motor in combination with mechanical brakes! The center diff will be turned around between its mounting pillars for installation.Contents:Motor mount with your choice of rear clamp for 57 / 57.8 / 60 / 70 mm motor diameterBattery carrier plate made of 3 mm epoxy with aluminum brackets for the hook-and-loop bands4 hook-and-loop bands to secure the batteriesaluminum mounting pedestals for the battery plate17T pinion with 8 mm bore diameterMounting screws Hobbywing Ezrun MAX5 ESC 250A with Top Tuning 700KV Brushless Motor 8S:Specifications 56112 ZTW Monster Brushless motor:Max. Amps: 175AMax. Voltage: 42VMax. Power: 7.350WKV (RPM/Volt): 700KVMounting hole depth: 8 mmBolt pattern: 4 x M4 on each 30 mmCase diameter: 57,8 mmCase length: 112 mmFree shaft length: 30 mmShaft diameter: 8 mmGewicht: 1260gSpecifications Hobbywing Ezrun MAX5 ESC 250A:technical Data :Type: 1/5 Brushless Sensored Current (continuous/short): 250A / 1600A Input voltage: 6-12S LiPo BEC: 6V/7.4V/8.4V @8A (switch mode) Motor types: Brushless motors (with/without sensor) Motor limits: - 8S Lipo: KV <= 1200 - 12S Lipo: KV <= 800 56118 motor Fan: Yes, operated via the BEC Programming: LED programming card LCD programming box (G2) OTA programming module Separate programming connection Waterproof: Yes Output: 8.00mm Bullet Connector (female) Size: 94.5x59.4x50.9mm Weight: 428.5g Applications: 1/5 buggy, truck Alternativ 12S:Hobbywing Ezrun 300A 12S Regler mit Top Tuning 620KV Brushless Motor:Technische Daten Regler ESC:Strom (dauer/kurz)300A / 2000AMotortyp:Sensor/Sensorlose Brushless MotorenMotorlimit:12S LiPo: kV <= 600 (70125er Größe)LiPo-Zellen:6-12SBEC:6V / 7.4V / 8.4V mit 10A (schaltbar)Lüfter:Ja (Versorgung über eingebautem BEC)Programmiereingang:Lüfter / PRG-EingangProgrammierung:LED Programmierkarte, LCD Programmierbox, OTA ProgrammiermodulGröße:125x85x61.7mmGewicht:775.4gNew waterproof sensor cableCompletely sensor-controlled system for more acceleration and greater power development.Best used with the Hobbywing Ezrun MAX5 HV G2 ESCWith high-precision encoder to detect rotor position to counteract interference and enable stable running in sensor mode.Use of high-quality components such as CNC-machined aluminum housing, high-purity copper windings, high-strength explosion-proof rotor, etc. for high durability and smooth running.Easily dismantled for maintenance workTechnical SpecificationsType:Brushless, SensoredkV Rating:650kVNo-Load Current:5.5ACells LiPo:8-12SPoles:4Diameter:56mmLength:119.2mmShaft Diameter:8mmShaft Length:30mmWeight:1272gApplication:1/5 Buggy, TruckDelivery1x Motor1x Manual Driving batteries with the following maximum dimensions can be installed: Length: 165 mm Width: 51 mm Height: variable The speed controller (ESC) requires EC8 connections or corresponding adapter cables! Features:High Quality BearingsRotor-4Pole High Quality MagnetsStator-Super Thin Silicon Steels Super Strength 8mm ShaftCNC Aluminium Heatsink ShellCopper Wires Of High Temperature EnduranceContents:1 set