27 products found for "y1471"

Catalogue #1

y1471 Turnbuckle wrench 6 mm

Genuine HT spare/option part. Handy wrench for 6 mm turnbuckles.Maße: Wrench size: 6 mmLength: 75 mmContent:1 piece

€9.90*

y1478 pump for re-fueling and de-fueling

The pump will fill and empty the fuel tank within seconds.The pump has a vent valve to avoid overpressure. Do not store gasoline for longer than 60 minutes in the gun.Occasionally lubricate the rubber seal of the piston with some grease. To do this, the handle-side cap of the cylinder can be unscrewed and the pump can be disassembled.The clear hose has been blackened in the picture for presentation purpose only.Color: blue.Filling capacity:500 mlContent:1 piece

€19.90*

y1470 Antenna tubes with caps, set of 5

Genuine HT spare/option part. Five antenna tubes with caps.Size: Length: 300 mmContent:1 set

€7.90*

y1475 Special front hinge pin brace set for Losi Mini

Genuine HT spare/option part.These hinge pin braces are machined from 7075 aluminum and feature an increased distance between the holes for the hinge pins. They are to be used in place of stock braces LOSB 078F.This allows the use of the front center drive shaft from the 5ive-T LOSB3218 at the wheels. This one is slightly longer than the Mini shaft for the wheels LOS252000, but will be available as spare part in the future. The turnbuckles on steering rods and camber links need some minor readjusting after assembly to restore the correct geometry.At the rear LOSB3218 driveshafts will fit the Mini without modifications. Set with one each front and rear hinge pin brace.Contents:1 set

€24.90*

y1474 Aluminum foil tape, self-adhesive, 50 mm x 45 meters

Genuine HT spare/option part.50 mm wide, self-adhesive aluminum foil tape, especially for heat insulation; i.e. between tuned pipe and plastic or electronic components.Content:1 piece / 45 meters

€9.90*

y1473 Extra strong duct tape, 50 mm x 50 meters

Genuine HT spare/option part.50 mm wide, extra strong duct tape, i.e. for repair of cracks in body shells or for preventative taping of RC car body shells.Content:1 piece / 50 meters

€6.90*

y1477 Losi 5ive-T/2.0/B and Losi MINI 300m steel HD differential drive cups, booted f/r

y1477 Versin: y1477/01 Set for the front axle

Genuine HT spare/option part.These heavy duty differential drive cups for front or rear differential in a Losi 5ive-T/B or MINI WRC are made of 300M / Böhler V132 steel and are characterized not only by high hardness, but also simultaneously toughness. The service life is therefore much higher than for the stock cups.300M steel is used in motorsport and aviation for high strength parts. As a highly pure material, it is significantly more expensive than conventional steels, its high basic strength and toughness make the machining a time-consuming task.The shape of these drive cups now allows the use of driveshaft boots and grease lubrication, which increases service life enormously. In addition, these HD drive cups have two sets of slots for the pin of the drive shaft, this means another doubling of the service life.We recommend y0809 Klüber grease for lubrication of closed HD drive cups.A dry run like with stock parts is theoretically possible, but absolutely not recommended because it would waive the enormous advantage of encapsulated lubrication and the associated wear reduction. The set for the rear includes modified stock alloy bearing carriers, which provide improved clearance for the driveshaft boots.You can find advices for installation at the specifications-tab.Contents:Front set:2 pieces of 300M steel HD differential drive cup, front and rear application2 pieces of driveshaft bootsRear set:2 pieces of 300M steel HD differential drive cup, front and rear application1 pair of modified bearing carriers2 pieces of driveshaft boots

€119.90*

y1461 SPEEDTEC air baffle

Genuine SPEED TEC spare/option part.The air baffle is said to improve cooling of the cylinder; it also protects against stones, which could lead to fins breaking off the flywheel.Also suitable for the Crank ignition system and when using a weight reduced flywheel like ST0010.Content:1 piece

€14.90*

This product is currently not available.

y1491/01 Fuel tank breather cap

Genuine HT spare/option part.Small aluminum breather cap for easy installation at the end of the breather hose, common on many tanks. It allows ventilation of the tank and keeps dirt from entering the breather hose.Color: silverContents:1 piece

€14.90*

y1481 RC-Paint Spray Gun

Fits most spray cans from many manufacturers.Convert your spray can into a spray gun. The long-lever system of this handle makes using a spray can much more convenient and provides better flow rate control as well.No more dirty hands from paint work.Contents:1 piece

€9.95*

y1441 Audi RS5 DTM clear

Audi RS5 DTM clear body shell for 1/5 cars with 530/535 mm wheelbase.The set includes main section and front air dam as well as the required special screws.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 530/535 mm wheelbase.Rear wing, side flaps/winglets and several decal sets are available from the options menu.The front section is also available separately as a spare part with part number y1441/01.This Audi RS5 DTM body shell is also available fully painted with either Team Audi Ultra (y1441/06) or Team Jägermeister (y1441/07) design.Required body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 3014 Body mounts Side body mount rear: FG 3014 Body mounts / for 4WD: FG 7014/02 Body mount

€239.90*

y1451 Steel machinist rulers 150 + 300 mm long

Genuine HT spare/option part. For the optimal measurement of the chassis.Steel rulers, 150 and 300 mm long.Contents:2 piece

€4.90*

y1441/03 Audi RS5 DTM Flaps/winglets

Fits Audi RS5 DTM body shell.

€22.90*

y1441/01 Audi RS5 DTM replacement front section

Fits y1441 Audi RS5 DTM body shell.

€39.50*

y1441/04 Audi RS5 DTM Rear wing mounts

Fits y1441/02 Audi RS5 DTM body shell rear wing and many other rear wings.Contents:2 pieces

€12.90*

y1441 Audi RS5 DTM clear, drilled wrong

Attention: Body was drilled wrong at the rear! The holes are slightly offset to the left (see pictures!)Audi RS5 DTM clear body shell for 1/5 cars with 530/535 mm wheelbase.The set includes main section and front air dam as well as the required special screws.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 530/535 mm wheelbase.Rear wing, side flaps/winglets and several decal sets are available from the options menu.The front section is also available separately as a spare part with part number Attention: Body was drilled wrong at the rear! The holes are slightly offset to the left (see pictures!)Audi RS5 DTM clear body shell for 1/5 cars with 530/535 mm wheelbase.The set includes main section and front air dam as well as the required special screws.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 530/535 mm wheelbase.Rear wing, side flaps/winglets and several decal sets are available from the options menu.The front section is also available separately as a spare part with part number y1441/01.This Audi RS5 DTM body shell is also available fully painted with either Team Audi Ultra (y1441/06) or Team Jägermeister (y1441/07) design.Required body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 3014 Body mounts Side body mount rear: FG 3014 Body mounts / for 4WD: FG 7014/02 Body mount

€219.90*

y1421 Engine quick mount for G320 Zenoah in FG 1/5 scale

y1421 Versiown: y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³

Genuine HT spare/option part. The engine quick mount replaces the standard clutch housing. It allows a much faster installation or removal of the engine since the clutch side of the engine is only be clamped by one single screw. The gear plate remains in the vehicle, the motor flange on the engine.The engine quick mount fits all FG 2WD on-road cars with horizontal engine (except Formula 1) Sportsline, Competition and Evo (EVO model range till 2003, except Evo 2020 series).We are sorry, but due to the design the quick mount cannot be used for FG 1/6 off-road and monster cars.For the first time it is now possible to install the Zenoah G320 in these cars! For cars allready equipped with a FG quick mount only the engine flange y1423/02 is required.The quick mount is available in two versions:y1421/01 for all Zenoah and Chung Yang engines up to 30 cm³ with standard bolt pattern 50 x 36 mmy1421/02 for Zenoah G320When mounting the motor flange the bolts/nuts must be tightened together in small steps. To mount the studs from y1421/01 or the screws from y1421/02 the use of thread locking compound (link) is required.Please note: y1421/01 does not fit in combination with Zenoah OEM clutch!

€74.95*

y1441/02 Audi RS5 DTM polycarbonate rear wing with mounts

Genuine HT spare/option part. Fits Audi RS5 DTM body shell.Dimensions: Length: 325 mmWidth: 60 mmDistance between mounting holes: 130 mmMaterial thickness: 2 mm Contents:1 piece

€24.90*

y1411 MadMax BIG DIGGER one pair front and one pair rear

Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The BIG DIGGER tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Dimensions:Outer diameter: 170 mmTyre width front: 60 mmTyre width rear: 80 mmContents:4 pieces / 2 pairs Some off-road tires knowledge can be found here!

€49.90*

y1411/02 MadMax BIG DIGGER one pair rear wheels 80 mm

Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The BIG DIGGER tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Dimensions:Outer diameter: 170 mmTyre width: 80 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!

€29.90*

y1441/07 Audi RS5 DTM body shell, painted, Team Jägermeister paint theme

Painted Audi RS5 DTM body shell with Team Audi-Jägermeister paint sheme for 1/5 cars with 530/535 mm wheelbase.With rear wing, flaps and decal sets for car and Jägermeister paint sheme.The body shell does not come with drilled mounting holes to make it possible to fit any 1/5 car with 530/535 mm wheelbase.This Audi RS5 DTM body shell is also available clear with part number y1441.Required body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 3014 Body mounts Side body mount rear: FG 3014 Body mounts / for 4WD: FG 7014/02 Body mount

€269.90*

y1371 SPEED TEC COMPETITION/Crank race ported top end set G320

Race ported top end set for Zenoah G320 engine. The SPEED TEC COMPETITION genuine Zenoah G320 race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina.SPEED TEC COMPETITION version modifications: Cylinder: Adjustment of compressionEnlarged portsFuel management milledMachined and polished exhaust and intakeThe case is specially matched with enlarged and polished cross section towards the portsy1016/002+3T Tuning transfer port covers:Reduced cross-section and flow-optimized transfer port cover plates for improved and faster gas flow for the Zenoah G320. The improved gas flow rate improves speed and gives faster throttle response in the medium rpm range. To improve mixture formation, the plates were glass bead blasted after machining. Piston: Weight reducedSkirt shortenedOil ringsPiston above and below piston ring tapered and piston dome polishedSet includes the following parts: CylinderPistonPiston ringCylinder foot gasketPiston pinPiston pin clipThrust washer for needle bearingCover for transfer portTo achieve the optimum performance gain of a SPEED TEC COMPETITION top end set, we recommend the use of a tuned pipe ().

€329.90*

y1411/01 MadMax BIG DIGGER one pair front wheels 60 mm

Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The BIG DIGGER tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Dimensions:Outer diameter: 170 mmTyre width: 60 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!

€24.90*

y1441/06 Audi RS5 DTM body shell, painted, Team Audi-Ultra paint theme

Painted Audi RS5 DTM body shell with Team Audi-Ultra paint sheme for 1/5 cars with 530/535 mm wheelbase.With rear wing, flaps and decal sets for car and Audi Ultra paint sheme.This Audi RS5 DTM body shell is also available clear with part number y1441.Required body mounts:Mount front: FG 7020/14 Front bumper Rear body mount: FG 7152/01 Rear body mount Side body mount front: FG 3014 Body mounts Side body mount rear: FG 3014 Body mounts / for 4WD: FG 7014/02 Body mount

€299.90*