13 products found for "y1149"
Catalogue #1
%
Small alloy engine mount.Suitable for Marder, Beetle, Pajero and Monster with CY / Zenoah G230/240/260/270/290 engine.
Complete set of four CRT stadium tires and rims, mounted and glued with tire inserts. Fits FG and Carson 1/6 scale cars.Tire diameter 170 mm, tire width 80 mm, 18 mm wheel square. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Also suitable for:With the following wheel adapter: y1183 Rim adapter
Genuine ZTW spare/option part. Features:Enchanced throttle response, excellent acceleration, linearity and driveabilityUsind the advanced PC interface allows you to set up, program or update the firmwareFully Programmable via LCD program card, PC interfaceAdjustable BEC output 6.0/7.4V, up to 8A current outputMultible protection features: Low voltage cut-off protection, over-heat protection and throttle signal loss protectionSpecification:Continuous Current: 300ABurst Current: 1800ABEC: 6,0 V/7,4 V einstellbar / 8 ABattery NIXX / LiPo: 18 - 36NC / 6-12S LiPoWidth: 74 mmLength: 115 mmHeight: 78 mmWeight: 500gProgrammable: JaWaterproof: splash proofThis esc is designed by ZTW for motors up to 800KV. Motors with higher KV ratings are not compatible.To change the firmware, the ZTW program card is required in conjunction with a PC.Contents:1 piece
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:7315 Clutch block carrier7315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch
Regular price: 54,80 EURSteel pinion set with one each 17T and 18T pinion.The GPM steel pinions are profile regraded. This allows for a change in gearing by a pinion swap alone. Module: m=1.5Profile regraded means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
%
Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all, necessary for installation, accessories (see also our pictures)One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline and E (in connection with alloy front uprights y0932Dimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set
%
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.If not on hand, for installation of the sintered steel clutch a clutch spring, the Zenoah screw set # 7318 and the original Zenoah clutch mount # 7315 are required!
%
y1549 ZTW Beast Pro 300A 12S ESC Features:Enchanced throttle response, excellent acceleration, linearity and driveabilityUsind the advanced PC interface allows you to set up, program or update the firmwareFully Programmable via LCD program card, PC interfaceAdjustable BEC output 6.0/7.4V, up to 8A current outputMultible protection features: Low voltage cut-off protection, over-heat protection and throttle signal loss protectionSpecification:Continuous Current: 300ABurst Current: 1800ABEC: 6,0 V/7,4 V einstellbar / 8 ABattery NIXX / LiPo: 18 - 36NC / 6-12S LiPoWidth: 74 mmLength: 115 mmHeight: 78 mmWeight: 500gProgrammable: JaWaterproof: splash proofTT70120 Top Tuning Beast Brushless Motor 620 kVSpecifications:Max. Amps: 200AMax. Voltage: 8-14SMax. Power: 10.000WKV (RPM/Volt): 620KVResistance: 0,0095Mounting hole depth: 8 mmCase diameter: 70 mmCase length: 120 mmFree shaft length: 30 mmShaft diameter: 8 mmGewicht: 1730gFeatures:High Quality BearingsRotor-4Pole High Quality MagnetsStator-Super Thin Silicon Steels Super Strength 8mm ShaftCNC Aluminium Heatsink ShellCopper Wires Of High Temperature EnduranceContents:1 set
%
y1549 ZTW Beast Pro 300A 12S ESC Features:Enchanced throttle response, excellent acceleration, linearity and driveabilityUsind the advanced PC interface allows you to set up, program or update the firmwareFully Programmable via LCD program card, PC interfaceAdjustable BEC output 6.0/7.4V, up to 8A current outputMultible protection features: Low voltage cut-off protection, over-heat protection and throttle signal loss protectionSpecification:Continuous Current: 300ABurst Current: 1800ABEC: 6,0 V/7,4 V einstellbar / 8 ABattery NIXX / LiPo: 18 - 36NC / 6-12S LiPoWidth: 74 mmLength: 115 mmHeight: 78 mmWeight: 500gProgrammable: JaWaterproof: splash proofTT56112/520Top Tuning Monster Brushless Motor 520kV Specifications Max. amps: 129 A Max. voltage: 57 V Max. power: 7,350 W KV (RPM/Volt): 520 KV Mounting hole depth: 8 mm Bolt pattern: 4 x M4 at 30 mm pitch circle diameter Case diameter: 57.8 mm Case length: 112 mm Free shaft length: 30 mm Shaft diameter: 8 mm Weight: 1260 g Connector: 6.5 mm diameter Cable size: 8AWG Features High quality bearings 4Pole rotor with high quality magnets Stator - super thin silicon steel layers Super strength 8 mm shaft CNC Aluminium heatsink case Copper wires with high temperature endurance Contents:1 set
Clutch spring for about 6,000 1 / min. for the OEM clutches from Zenoah and many other rc-car engines from 23 cm³ - 32 cm³.Content:1 piece
Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:5315 Clutch block carrier5315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch
Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the green colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the HPI-Baja 5B series with 170 mm tire diameter is available in two widths.Replacement part for MadMax Multi Pin and Giant Grip tires.