44 products found for "y0720"

Catalogue #1

y0720 rc-car-online Transmitter bag

Genuine HT spare/option part. Extremely sturdy, fully padded transmitter bag! Fits all popular pistol grip transmitters Top quality; with padded adjustable length retaining straps to secure the transmitter, large zippered flap and adjustable carrying strap. Dimensions: Width: 23 cmHeight: 34 cmDepth: 17 cmContents:1 piece

€24.90* €34.90* (28.65% saved)

y0728/06 GRP tires sponsor decals

Sponsor decal set from GRP with five GRP lettering.Measures:Width: 150 mmLength: 140 mm

€4.90*

y0722 Axle plugs for Losi 5ive-T/2.0, Mini

y0722 Quanity: y0722/02 - Set of 10+ 3EUR

For sealing the axles on Losi 5ive-T and Mini cars, keeps debris out of the inner screws which secure the retainer pin. Set of 4 or set of 10 to choice.Can be used for Losi 5ive-T, Mini and HPI Baja cars.

Variants from €3.90*

€6.90*

y0728/04 Decal set for 1/5 scale Lancia Delta Martini

Decal set with the original Lancia Delta Martini venyl. Lights, indicator, rear lights are also included.Measures:Width: 350 mmLength: 500 mm

€19.90*

y0726 Gas-nitrided tuning clutch bell for Losi 5ive-T/2.0/B and Mini

Gas-nitrided tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding.Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Extreme clutch.Suitable for genuine slot drive Losi pinions. Comes with bolts and spring washers included.The bolt hole is countersunk from the inside so you can also use a flat head screw from the inside and a nut on the outside if you like. Content:1 pieces

€49.90*

y0721 Receiver battery, hump pack, NiMh, 4500 mAh

y0721 Connector: y0721/01 - BEC

5 cells, 6 volt, cell size Sub-C.Fits for all HPI 1/5 scale models.Dimensions: approx. 69 x 51 x 42 mmUniversalFGBECHigh current

€54.10*

y0723 Gas-nitrited tuning clutch bell for FG, Smartech/Carson, Harm, RS5 & Co.

Genuine HT spare/option part. Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.Contents:1 piece

€49.90*

y0726/01 Gas-nitrited tuning clutch bell for Losi DBXL+MTXL

Genuine HT spare/option part. Gas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.Contents:1 piece

€49.90*

y0730/14 Clutch housing main section

Genuine GPM spare/option part. Part no. 14 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€19.90*

y0729 Gas-nitrited tuning clutch bell for HPI Baja, Carson Wild GP Attack models, 1 pce.

Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM clutches Big Scale Extreme and Cross.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.

€49.90*

y0730/17 Clutch housing

Genuine GPM spare/option part. Part no. 17 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€22.90*

Receiver switch, Multiplex connectors old, y0920 - 1pce.

Old version Multiplex type connectors for both battery and receiver.

€10.10*

y0730/01 Clutch shoes with pads

Genuine GPM spare/option part. Part no. 01 for GPM Big-Scale clutch. Installation ready set of 3 with glued-on organic pads.Replacing the clutch liningsFor replacing the friction pads please proceed as follows:1. Remove clutch from engine2. Disassemble clutch3. Remove the screws fixing the friction pads4. Remove remains of old glue and clean the surface to be bonded of the shoes to bare metal 5. Thoroughly degrease the bonding area of clutch shoes and new pads6. You must use the special adhesive y0743 Clutch-Safe!7. Apply a sufficient and complete layer of the adhesive to the bonding surfaces8. Insert the lining into the clutch shoe and align9. Fix the pad in place with screw y0730/03, just hand-tighten it10. Remove excessive glue with a rag11. Preheat oven to 120 °C.12. Put the clutch shoes into the preheated oven for exactly one hour; let the parts cool down13. Reassemble clutch and install it onto the engine14. Wait at least one hour after the gluing process before using the clutchy0730y0731 Content: 3 x aluminum clutch shoes with3 x press-fitted dowel pins (part no. /15) with3 x glued-on organic clutch pads (part no. /02) with3 x M3x5 mm safety screws (part no. /03) installed

€47.90*

y0730/19 Full-aluminum clutch shoes conversion kit

Genuine GPM spare/option part. Full aluminum clutch shoes are very successfully used in 1/5 onroad racing applications.Therefore we can now offer the GPM conversion kit for BigScale Cross/Race clutches to full-aluminum clutch shoes. Made of a special alloy to suit this application the kit comes with 1.4 mm wire diameter springs and new spring pressure plates.Slight aluminum deposits in the clutch bell and corresponding wear marks in the clutch shoes are normal with the Big Scale ALLOY clutch and have no negative effect on the function. Caution: It is very important that when swapping the full-aluminum clutch shoes against the organic friction pads of a Big Scale CROSS or RACE to use a different or new , because the rough surface of the aluminum deposits in the clutch bell left by the Big Scale ALLOY will cause a high wear on the organic pads.y0730y0731Content:1 set

€54.90*

y0820 Robbe synthetic oil for plastic parts, 1 pce.

Special oil for plastics in precision applicator; following special advantages:- Friction reduced ten-fold- Completely smooth running- Wear reduced by 90%- Resistant to fuel attack and ageing- Does not attack plastic materials- Temperature range -30°C to 150°C Applications:- Bowden cables- Ball-links and joints- Plastic differentials- Transverse armcontent 4ml

Content: 4 Milliliter (€8,700.00* / 1000 Milliliter)

€34.80*

y0730/13 Bushings for clutch shoe pins

Genuine GPM spare/option part. Part no. 13 for GPM Big-Scale clutch.Dimension:Inside diameter: 3 mmOutside diameter: 4,5 mmFlange: 7,2 mmy0730y0731Content:6 pieces

€4.90*

y0730/15 Pins for clutch shoes

Genuine GPM spare/option part. Part no. 15 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€2.90*

This product is currently not available.

y0730/04 Spring pressure plates, outer side (with positioning pin)

Genuine GPM spare/option part. Part no. 04 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€8.90*

y0702 Copper-Exhaust gasket for Zenoah, CY, Fuelie, PT, etc.

Genuine HT spare/option part. For all Zenoah G230/240/260/270/290/320 / CY / Fuelie / PTTemperature and dimensionally stable. Thickness: 1,0 mm.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece

€4.90*

y0730 GPM Big Scale-Cross adjustable 3 shoe clutch

Genuine GPM spare/option part. The Big Scale-Cross clutch is equipped with 1.3 mm springs, is especially suitable for Off-Road use.Adjustable 3-shoe clutch for:ZenoahChung YangHPI - FueliSmartech PTAnd many other enginesThe GPM-Big Scale clutch:Suitable for racing and for the ambitious hobbyist driver. Unlike the stock clutch, the installed GPM-Big Scale clutch can be adjusted by turning one single screw. A 2.5 mm allen key wrench is required for this application.Therefore it is possible to precisely adjust the clutch engagement depending on track characteristics.Attention: You must use adhesive y0743 Clutch-Safe when replacing clutch pads!y0730y0731Content:1 piece

€99.90* €129.90* (23.09% saved)

y0730/06 Replacement spring gold 1.4 mm

Genuine GPM spare/option part. Equipped with the gold 1.4 mm springs the Big-Scale clutch provides medium slippage and noticeable clutch engagement at medium to higher rpms. On-road clutch standards.Part no. 06 for GPM Big-Scale clutch.y0730y0731Content:3 pieces

€8.90*

y0730/09 Adjustment cam Big-Scale clutch

Genuine GPM spare/option part. Part no. 09 for GPM Big-Scale clutch.y0730y0731Content:1 piece

€18.90*

y0270 Alloy differential case conversion kit for FG 2WD models

alu_diff_umbau Application: y0270/02 FG

Genuine HT spare/option part.Alloy case conversion kit for Smartech / Carson 2WD and FG 2WD large scale cars .Comes complete as shown with reinforced differential tube, sealed bearings, installed needle bearings, shims, screws and o-rings.The scope of supply for FG:4 x Countersunk screw M4 x 8 mm2 x Shims 8 x 20 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffThe scope of supply for Smartech:4 x Countersunk screw M4 x 8 mm4 x Shims 8 x 20 x 0,10 mm8 x Shims 5 x 17 x 0,10 mm2 x Lenticular flange head screw M3 x 10 mm2 x Washers 3,2 mm2 x Gasket for DiffContents:1 set

€99.90*

y0750/05 Case set for Orange-Power servo

Complete case set for Orange-Power servo with o-rings and screws included.

€24.90*