Genuine FG spare/option part. By mounting the carbon fiber reinforcement deformation of the rear plastic damper plate can be minimized. Recommended at higher ambient temperatures.Suitable for all FG models except Evo and Formel 1.Contents:1 piece
Genuine FG spare/option part. The complete rear axle assembly is bolted to the solid alloy riser plates. You can now install this unit with only 4 countersunk screws to the chassis, which makes for a very fast change of the complete end.Replacement for plastic base plate FG 7068.Height 9 mmContent:2 pieces
Genuine FG spare/option part. Plastic radio plate for installation of up to 4 servos. Fits all FG street models (except Formula 1) and Leopard models.You will need FG #6118/05 for installation of any steering servo other than Hitec 805BB.Contents:1 piece
Genuine FG spare/option part. Replacement chassis for FG touring car EcoLine/SportsLine models with short wheel base 465 mm.4 mm alu-chassis. Contents:1 piece
Genuine FG spare/option part. One-piece titanium front axle shaft with 9.5mm wheel square.orrosion resistant and 40 % less weight compared to steel.Diameter 8 mm.Contents:1 piece
FG body kit Alfa Romeo 156 WTCC made of 1 mm Lexan, painted. The body kit consists of the main body, front body and rear spoiler and is
is red/black, as shown in the photos. The rear spoiler is painted black. The window frames have been painted black and the windows are slightly tinted. There are no holes drilled in the body and can therefore be fitted to any on-road RC car with a 530 mm wheelbase. Body mounts required: Front part: FG 7020/10 Front bumper Rear carrier: FG 7152/01 Rear body supportFront side: FG 8013 Body support Rear side: FG 7014 Body support Dimensions: Length: 900 mm Width: 400 mm Height: 245 mm Wheelbase: 530 mm Contents
1 piece
The 2WD-465 Sportsline model is built on the short chassis with double a-arms suspension front and rear. The vehicle is equippedwith the 2-shocks front suspension as standard, which ensures optimum traction for both front wheels.On the GT2, the front axle has been widened to 384 mm. The rear axle is 395 mm wide.Technical description:The model has a 465 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads! The car comes with an unpainted body shell.Also available painted in the shop selection!Dimensions: Length: 840 mm Width: 395 mm Height: 250 mm Wheelbase: 465 mm HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included. Value: 64,95 EUR Alloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EUR Ball bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURTouring cars in action!Painting tips:
Tuning 3 chamber resonance pipe from FG for the short wheelbase. Set with manifold and connector as well as the mounting. See photos for condition and scope of delivery. 1 piece
€75.00*
This website uses cookies to ensure the best experience possible. More information...