Genuine HT spare/option part. With non-slip surface perfect for delicate work, actually improving dexterity and grip.Available sizes: 8, 9 and 10.Glove size?Size 8 = 21 cm (S - L) circumferenceSize 9 = 24 cm (L - XL) circumferenceSize 10 = 27 cm (XL - XXL) circumferenceMeasure the circumference of your hand without the thumb and at the widest point (above the ankle). The tape measure should embrace the hand loosely.Norm EN388, Lining 100% polyamide.Partially coated with hightech nitrile Fits like a second skinGrips even when wetGood touch sensitivityLiquid-repellentGood resistance against oil and greaseContents:1 pair / 2 pieces3 pairs / 6 pieces
Genuine rc-car-online spare/option part. Very high quality Torx screwdriver blades with ¼ hexagon shaft and engraved size indication.The complete set consists of:Eight with in the following sizes: T6, T7, T8, T9, T10, T15, T20, T25Handle with magnetic ¼ hexagon socket to accept the Torx bladesThese are the most usual Torx sizes required for working on rc-cars.The ergonomically shaped handle features a magnetic ¼ hexagon socket, a polished surface and a cross bore.Unit price: 53,10 EUR.Contents:1 set
Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaftSuitable for all servos with an output shaft with 15 tooth spline shaft, for example:Multiplex RhinoHitec 805Savöx SV-0236MGLOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)and many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces
Rebuild kit for the Zenoah G270 engine to replace piston/cylinder related parts. The kit includes the following parts:Cylinder G270Piston G270Piston ring G270Piston pin G270Piston pin retainer clipsCylinder gasketPlease note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece
The SPEED TEC EXPERT genuine 5ive-T engine is optimized for performance with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust and intake. Piston: weight reduced; skirt shortened; oil rings, piston above and below piston ring tapered and piston dome ground. Crankshaft: is adjusted and aligned. Flywheel: weight reduced and checked for runout. Gaskets: use of premium quality gaskets.To achieve the optimum performance gain of a SPEED TEC EXPERT engine, we recommend the use of a tuned pipe (to the tuned pipes).
Rear lower a-arms for all FG Evo cars (except 2020 series) that will bring the car to Race Truck width. The arms can also be installed as an upgrade in Sportsline trucks up to and including the 13 series. The arms are compatible with all other FG parts like uprights, Evo shock mounts and Evo stabilizer bar.Due to the increased width you will also need longer driveshafts turnbuckles for the upper a-arms and shock shafts for installation in an existing Evo. When upgrading a Sportsline truck to the Evo parts you will need a complete Evo stabilizer bar and shock mounts, rose joints and conical spacers instead. Regular price: 129.90 EURSpecial offer: 89.90 EURContents:2 pieces
Very high quality Torx screwdriver blades with ¼ hexagon shaft and engraved size indication.Sizes T7 to t25 are usually required for rc-cars.Available sizes:T6, T7, T8, T9, T10, T15, T20, T25
Genuine GPM spare/option part. These protective covers prevent the shock piston rods and seals for wear caused by dirt. They fit most 1/6 and 1/5 scale shocks.Does not fit FG, Carson (thin shocks) , Smartech, Conrad!Suitable for all Carson Wild GP Attack, HPI Baja, Hell-Devil, Super Baja Rey, Super Rock Rey, Gas Devil, CRT 4x4, Thunderbolt and all shocks with a diameter from 26 to 40 mm. Please note that the shocks shown in the picture are for presentation purpose only and not included.Contents:2 pieces length 160 mm 2 pieces length 180 mm
Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaft!Suitable for all servos with an output shaft with 15 tooth spline shaft, for example:Multiplex RhinoHitec 805Savöx SV-0236MGLOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)and many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces
Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaftSuitable for all servos with an output shaft with 15 tooth spline shaft, for example:K-Power DM4000Multiplex RhinoHitec 805Savöx SV-0236MGSpektrum S9010 and S9020LOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)Losi SPMS904 WPand many more!holes for linkage with M4 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces
For all tire adhesives above,15 ml pump spray bottleAccelerator-spray is the second component to cure superglue immediately.Advantages: Tangible adhesion after a few seconds Aromatic solvents and hexane free Suitable for hobby, craft, industry and household.Processing:Clean the surface thoroughly. Apply accelerator at room temperature on both surfaces to be bonded until a clear liquid film appears. Air out the applied accelerator, then apply the superglue as usual.
Optimal supplementary set for ARR and kit models. Especially for cars and boats.Transmitter / receiver Operating voltage transmitter 4.8 to 6 V two continuously adjustable, fully proportional channels Servo reverse for both channels (reversal of running direction) Trim function for throttle and steering Dual rate for both channels (travel limitation of the servos) Receiver power supply (without BEC) possible up to 11 V Integrated fail-safe Uni plug system for Futaba and Graupner-J/R Charging socket (positive pole inside) Battery status display using LED Charger Input voltage: 100-240V, 50/60 Hz (AC) Charging current output 1: max. 2 A / 9 V Charging current output 2: max. 0.5 A / 6 V Battery types: NiMH Control servo JR plug 6 kg actuating force Metal gears Drive battery NiMH 7.2 V / 3000 mAh TAMIYA plug Transmitter battery NiMH Mignon 1.2 V / 2100 mAh 2-channel 2.4 GHz transmitter, 4-channel mini receiver, Expert Charger Carand Radio, 7.2V/3000mAh driving battery, CS-6 steering servo, 4x 2100 mAh Mignon transmitter batteries and instructions.
Genuine K&N spare/option part. K&N Power Kleen is a high-performance cleaner and degreaser used to remove road grime, engine exhaust and grease from cotton air filters. It is now formulated to clean those troublesome and demanding cleaning jobs. This cleaner is specially formulated to remove oil, lubricants, grease, grime, and other deposits from most surfaces including cotton air filters, painted surfaces, chrome, plastic and more! Genuine K&N air filter cleaner,especially formulated for cleaning cotton air cleaners.Content:946 ml / 32 OZ
Genuine HT spare/option part. High visibility bright yellow safety vests for drivers and assistants, highly recommended for racing and training tracks. It should be kept in mind that large scale 1/5 or 1/6 cars weigh more than 10 kg and can be very fast! On most tracks safety vests are required specifically for volunteers. Note: The carriage of a safety vest in the real car is compulsory in almost every country of the EU! These vests were specifically manufactured for the rc-car sport and carry the print "Race Track Marshal" on the back; they also meet the safety standards for the automotive sector.Prices:9,90 EUR eachSponsored volume price for clubs: 29,90 EUR / pack of tenContents:1 piece
The SPEED TEC COMPETITION genuine 5ive-T engine is optimized for performance with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC COMPETITION version modifications: Cylinder: Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust and intake, the case is specially matched with enlarged and polished cross section towards the ports, oil holes for optimized lubrication of the crankshaft bearings. Piston: weight reduced; skirt shortened; oil rings, piston above and below piston ring tapered and piston dome polished. Crankshaft: is adjusted, aligned and balanced, high quality Fluon shaft seals and Top Drag Seals installed. Flywheel: weight reduced and checked for runout.Insulator:mounted SPEED TEC tuning insulator. Gaskets: use of premium quality gaskets.To achieve the optimum performance gain of a SPEED TEC COMPETITION engine, we recommend the use of a tuned pipe ( to the tuned pipes ).
Race ported top end set for the original 5ive-T 26 cm³ engine.The SPEED TEC EXPERT genuine Zenoah G260 race ported top end set is optimized for performance with sophisticated craftsmanship and when accurately installed - guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compressionEnlarged portsFuel management milledModified exhaust and intake Piston: Weight reducedSkirt shortenedOil ringsPiston above and below piston ring tapered and piston dome ground The set includes the following items: Performance-optimized cylinder and piston, piston ring, piston pin, piston pin circlips and cylinder gasket.To achieve the optimum performance gain of a SPEED TEC EXPERT top end set, we recommend the use of a tuned pipe.Each SPEED TEC Tuning cylinder set comes with a small amount of a spec. assembly lube for the installation of piston and piston ring. This spec. lube provides the required lubrication to the engine for the first start and dissolves without residue!
Split aluminium servo lever for more gentle screwing (with a 2.0 mm Allen key) with clamping on the servo output shaft! For servos that have an output shaft with a 17 mm multi-tooth shaft. For our y2006 Top Tuning digital Pro Servo 40 Kg Mounting holes with 3 mm diameter If you count the teeth on your servo, you can determine whether this aluminium arm fits your servo.
Aluminium servo arms are indispensable for powerful digital servos, such as those used in large-scale models.
€14.90*
This website uses cookies to ensure the best experience possible. More information...