HT Replacement bushing 6 x 8 9.5 mm, y1115, 4 pcs.

To ensure the required cooling for current 1/5 and 1/6 engines the flywheels have fins on both sides. Therefore the fan housing has large openings on the crankcase side for the required air supply. However, the risk of foreign objects (grass, sand, or even stones!) entering here Is very high! As a result, broken fins on the flywheel occur frequently. This leads to reduced cooling efficiency and - even more critical vibrations from a flywheel which is out of balance due to missing fins. Therefore, this kind of flywheel protection is highly recommended, especially for offroad use. The product video explains the handling in detail! Note:It is essential to thoroughly clean and degrease the crankcase prior to attaching the hook-and-loop tape (OKS2661)!For installation on Chung-Yang and Zenoah engines in FG cars, the crankcase cover must be slightly modified in two places where the engine mount is attached (see Figure 6 and 7). Furthermore the fit of the fabric must be as tight as possible in the region of the layshaft pinion (in front of the differential ring gear!) (see Figure 8).Set includes:Special tailored fabric with sewed on hook-and-loop tapehook-and-loop tape for installation to the crankcaseAdhesive for securing the hook-and-loop tape

Genuine Top Tuning spare/option part. Indispensable for optimal suspension tuning!Vacuum container for removal of bubbles from shock fluid when filling shocks.A vacuum pump is built into the lid. The tray has four holes each to accept 1/10, 1/8, 1/6 and 1/5 scale shocks.Suitable for shock absorbers from Losi, Mecatech, BWS, Arrma, Traxxas, FG, Carson, HPI and many more, as long as they have a suitable diameter. All shocks from 15 to 32 mm outer diameter can be used in the Bubble Ex to be "de-bubbled". Tray bore sizes: No. 1 = 32 mm diameter No. 2 = 21 mm diameter No. 3 = 17.5 mm diameter No. 4 = 15 mm diameter The maximum length of the shock absorber up to the upper edge of the body is about 150 mm, whereby longer shock absorbers can also be partially compressed for insertion. (e.g Losi 5ive-T and many more)Operation:Unlock the vacuum pump by turning it slightly to the left, the pump handle then extends a little. The small plug with handle is used to close and ventilate the container. To build up the vacuum, the plug must be in the down position.The small membrane on the opposite side serves as an indicator for whether a vacuum is present. Only when this is curved outwards the lid of the container can be opened again without any effort. Content: Can with integrated vacuum pump Shock tray

Genuine HT spare/option part.Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.For FG Off-Road rims 60200, 60201 (wide) and 60205, 60206 (narrow).14 mm wide square drives must be used.Please note:When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.Contents:2 piece

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces