y1107 Steel balljoints 5mm/M8, with conical spacers

Alloy rear axle conversion kit for Smartech UNO and Carson Attack and Super Attack (not Evo!), Gas Blaster and C5; Smartech Spider and Ranger cars.Fits for:- C5 / On road / Touring car- C6 Attack- Touareg- Super Attack- Gas Blaster- Duratrax Firehammer- Spider- Big AttackThe set includes:- rear plate- differential mounts- lower a-arms- upper a-arms- installation hardware.Please note: must use inge pins 6075, also you need two packets turnbuckle 40 mm 6100/04.

Different versions to choose:y0723 Gas-nitrited tuning clutch bell for FG, Smartech / Carson, Harm, RS5 & Co..Gas-nitrited tuning clutch bell; machined from high grade steel with vents for cooling of the clutch system and holes for easy clutch adjustment. The clutch bell features a significantly reinforced wearing surface which guarantees dimensional stability even under high loads!For best mounting of the pinion the clutch bell shaft has to flats with a 90° offset. As an additional safety device a M5 bolt with washer (included) replaces the E-clip found on stock clutch bells.Suitable for many 1/5 and 1/6 cars, such as all FG (except Formula 1), Carson a.s.o.y0726 Gas-nitrited tuning clutch bell for Losi 5ive-T (unfortunately not available at the moment Alternatively original Losi clutch bell # LOSB5038) )  Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface and face which guarantees dimensional stability even under high loads! The shaft is a tiny bit longer than stock (about 0.2 mm) to prevent the bearings from binding.Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for genuine slot drive Losi pinions. Comes with bolts and spring washers included.y0726/01 Gas-nitrited tuning clutch bell for Losi DBXLGas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.y0729 Gas-nitrited tuning clutch bell for HPI Baja models, 1 pce.Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM Big Scale-Cross clutch.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.

Genuine Mecatech spare/option part for the FW01.Content:1 piece

Aluminum or steel balljoints for replacement of the stock plastic units on the a-arms of all FG cars except Formula 1. Alloy:A = 5 mmB = M8C = 8 mmD = 17,5 mmE = 39 mmSteel:A = 5 mmB = M8C = 8 mmD = 16 mmE = 37,5 mmContent:8 x Aluminum or Steel balljoints, M8 r/h thread, 5mm bore diameter in the ball8 x low height nut, M8 r/h thread 16 x conical alloy spacer

The Samba 8 titanium gives you a weight saving of 140 grams compared to the steel version. We have tested and optimized the Samba 8 Titan- tuned pipe system for half a year on the engine dyno and an additional three months on various racetracks! The pipe has a new, very strong connection system. This low-maintenance flexible connection between pipe and manifold is secured by four (!) springs, making a failure prone o-ring seal obsolete! Despite of the increased performance fuel consumption remains the same compared to a Samba 7 pipe. The Samba 8 system provides significantly better performance, i.e. the power is optimally available across the engines entire rpm range! Again and again, podium places are achieved at major events through the use of Samba tuned pipe systems.Of course, the Samba 8 tuned pipe system is race legal for racing, with the DMC approval number 10-1504 engraved. The Samba 8 - tuned pipe system comes with an installation kit.Fits: All On-road cars from FGContrastBergonzoniHarmGeniusand many others as wellOriginal statement from Samba: "This new tuned pipe system is the result of the development of the Samba 7 tuned pipe!"

Steel ball joint 6 mm r/h or l/h thread, 4 mm bore in ball, for steering rods and other applications.This version is for steering rod applications.Sets available:One each with r/h and l/h threadOne x r/h threadOne x l/h thread Please note:We recommend using a nut 4472/03 for locking the r/h thread ball joint to prevent the linkage from loss of adjustment.