16 products found for "y0306"

rc-car-online - Home

y0306 Step drill for body work

Genuine HT spare/option part. Small and handy step drill, made of TiN-coated HSS steel with steps of 4/6/8/10/12 mm. Split point tip for good centering, 6 mm tri-flat shank for sure grip. For use with drills or with our hand chuck.Contents:1 piece

€9.90*

y0206 HT steel pinion 18 teeth Carson/Smartech Offroad 2WD models

Original rc-car-online spare/tuning part. The sprockets are milled from steel and nitride-hardened. They all fit on the standard main gear and are fastened with 2 grub screws. The sprockets are profile-shifted and therefore all have the same diameter! Module: m=1.51 piece

€29.90*

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

y3006 rc-car-online decal sheet yellow

Genuine HT spare/option part. rc-car-online lettering with correspondig logo. All decals are cutted with a plotter. Dimensions:Sheet with car logos: 450 x 160 mmSheet with rc-car-online letterings: 450 x 140 mmContents:1 piece

€7.90*

Bowden cable, Baja premium brake, 1 pce., y0006

Sheath complete with core cable.Length: 315 / 395 mm

€15.90*

y0806 SPEED TEC Chung-Yang original 26er EXPERT tuning engine

The SPEED TEC EXPERT genuine Chung-Yang engine is optimized for performance with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust and intake. Piston: weight reduced; skirt shortened; oil rings, piston above and below piston ring tapered and piston dome ground. Crankshaft: is adjusted and aligned. Flywheel: weight reduced and checked for runout. Gaskets: use of premium quality gaskets.To achieve the optimum performance gain of a SPEED TEC EXPERT engine, we recommend the use of a tuned pipe ( to the tuned pipes ).

€599.00*

y0376 Replacement spring for Samba manifolds - 2 pcs.

Measures:Total length: 55 mmLength of coils: 25 mmWire thickness: 1,25 mm

€4.90*

2009-01 Cask shaped springs for Mecatech Klick-Shocks, orange 2,5 mm

These cask shaped springs are especially designed to fit the diameters of Mecatech Klick-Shocks and Mecatech Big Bore shocks.Dimensions:Inner diameter, upper: 20,5 mmInner diameter, lower: 16,5 mmOutside diameter: 29,5 mmLength: 55 mmWire diameter: 2,5 mm

€17.20*

y0356 Circle cutter, 1 pce.

A nice tool to create clean circular cuts in Lexan bodies. Adjustable for diameters from 10 to 150 mm. Storage compartment with six blades.Inhalt:Circle cuttersix replacement blades

€9.90*

y0302 Torx screwdriver T25

Genuine HT spare/option part.High quality Torx screwdriver.Contents:1 piece

€11.90*

y0305 Colored flexible fuel line, top quality, 1 meter

y0305 Color: y0305/06 - Orange

High quality flexible fuel line in your choice of blue, red, yellow, orange and green. Size:Length: approx. 1 meterOuter diameter: approx. 6.3 mmInner diameter: approx. 3.2 mmDiameters are 100% identical to the Zenoah Tygon hose #7352!

€5.90*

y0906 HT Monster / Stadium alloy front suspension kit 2WD - 1pce.

Alloy front axle kit for FG Monster and Stadium 2WD models. Complete kit with all necessary parts. A-arms and bulkheads feature replaceable bushings, shock stay, shock quick mounts, balljoints, and droop stop.Fits FG Monster and Stadium 2WD models.All components are available separately.Quantity Order N° Kind 2 pieces 18000 A-arm front upper 2 pieces 18001/l+r A-arm front lower 2 pieces 18006 Front bulkhead 1 piece 18004 Shock tower2 pieces 18003Shock mounts4 piece 18005 Absorber quick mounts1 piece 18007 Suspension travel limiter2 pieces y1036 Rose jointsThe price of those parts bought separately would be 451,80 EURIf you want to install front cable brakes, we recommend the brake cable bracket below.

€379.00* €451.80* (16.11% saved)

FG Off-Road Buggy tires and rims, y0304, 4 pcs.

y0304 Mounting: Tires not mounted

Complete set of genuine FG Off-Road tires & rims, including one pair each front tires with insert, rear tires with inserts, front and rear rims, not glued. Tire diameter 180 mm, tire width 60 mm in front, 75 mm in rear. Fits all FG and Carson buggy and monster models. 18 mm wheel square, minimum square width 9.5 mm.

€124.70*

y0309/03 Gasket small for bleeder valves, 4 pcs.

Item N° y0309/03Gasket small for bleeder valves, 4 pcs.Spare part fits

€11.80*

y0309/01 Gaskets for bleeder valves, 4 pcs.

Item N° y0309/01 Gaskets for bleeder valves, 4 pcs.Spare part fits

€11.80*

y0309/04 Screws for bleeder valves, 10 pcs.

Item N° y0309/04Screws for bleeder valves, 10 pcs.Spare part fits

€7.00*

16 products found for "y0306"

Filter products

rc-car-online - Home