The V-pin competition tire is particularly suitable for tracks with loose and sandy surface. The high tread profile, extended to the tire shoulder requires a high manufacturing cost. This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum. A well proven combination is the use of in the rear and V-pin at the front. By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering.Please take a look at the corresponding pics:Pic A - very high lateral grip = car tends to oversteerPic B - high lateral grip = still sharp steering responsePic C - reduced lateral grip = neutral handlingPic D - low lateral grip = expect the car to understeerOf course, the before mentioned does depend on the track surface!Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.For very loose soil the soft compound is recommended, under normal condition the medium compound is usually your best choice.HPI Baja 5 cars can also use these tires when equipped with special adapters. Dimensions:Diameter: 163 mmWidth: 65 mmInner diameter: 106 mm

The V-pin competition tire is particularly suitable for tracks with loose and sandy surface. The high tread profile, extended to the tire shoulder requires a high manufacturing cost. This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum. A well proven combination is the use of Mammoth tires in the rear and V-pin at the front. By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Please take a look at the corresponding pics:Pic A - very high lateral grip = car tends to oversteerPic B - high lateral grip = still sharp steering responsePic C - reduced lateral grip = neutral handlingPic D - low lateral grip = expect the car to understeerOf course, the before mentioned does depend on the track surface!Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.For very loose soil the soft compound is recommended, under normal condition the medium compound is usually your best choice.Dimensions:Diameter: 163 mmWidth: 65 mmInner diameter: 106 mmPrices of the components:V-Pin tires EUR 39.90 / pairV-Pin tire inserts EUR 9.90 / pairRims FG 6105/01 EUR 14.90 / pairglue set y0067 EUR 13.30Total EUR 78.80Ready mounted and glued EUR 69.90 / pairRim with 18 mm square driveAlso suitable for:With the following wheel adapter: y1183 Rim adapter

Genuine HT spare/option part. Once again misplaced nut or bolt or, or ... . The tray for small parts with magnetic vinyl brings this to an end!Dimensions: Length: 105 mmWidth: 85 mmdepth: 10 mmContent:1 Piece

With complete RTR equipment y1382 Original Maxi-Pin 1/6 offroad competition tire The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder comes with completely installed remote control. Just fuel up, start the engine and drive off.Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm