y1445 MadMax Maxi Pin tyre, 1 pair
Product number:
y1445
Product information "y1445 MadMax Maxi Pin tyre, 1 pair"
MadMax MAXI PIN tyres have been specially developed for carpet race tracks!
The special block tread pattern, with 480 knobs per tyre, provides excellent grip, but also puts extreme strain on the tyre and the rim.
To stabilise the tyre, the outside of the tyre shoulder is equipped with vertical ribbing on the side, which minimises tilting under load and counteracts the shear forces that occur in bends.
Furthermore, the MAXI PIN tyres have knobs positioned on the side of the outer side, which particularly support the steering behaviour of your RC car in bends.
Taken together, the MAXI PIN tyres provide maximum grip.
Dimensions:
Outer diameter: 185 mm
Tyre width at the outer edge of the tread: 75 mm
1 pair
Login
Customers also bought
tt_tt1021_07 Version:
TT1021/07A - Type A with 15 teeth
Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece
The off-road tire for hard packed dirt and spectacular drifts!Gives great results on those carpets which are typical for some off-road tracks. 616 grippy square studs per tire, a total of more then 2.400 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability and allows for spectacular drifts! Therefore the car is less prone to undesirable side rolls!The Narrow-Grip 616 tires are mounted on a flexible 10 spoke rim with steel ring reinforced 24 mm hex drive. 10 screws per beadlock ring keep the tires in place. The Narrow-Grip 616 tires feature a firm foam insert, making them suitable even for heavier weight cars.To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with the hex drive and completely mounted via tightening the wheel nut! Attention: When using the Narrow-Grip wheels on a Super Losi Rock-Rey model, special wheel hexes are required. Also on FG and Carson models. For mounting on a Traxxas X-MAXX you need a set of special Top-Tuning wheel nuts. - TT1040 Top Tuning wheel hub 24mm/6-edge for Losi Super BajaRey/2.0 and Super Rock Rey for plastic axle stubs. - AT-004 Atop wheel nuts 4 pieces Dimensions:Outer tire diameter: 180 mmTire and rim width: 60 mmRim inner diameter: 120 mmWeight for one tire: 430 grams / for a pair: 860 grams24 mm hex for Losi 5IVE-T, HPI Baja 5, MCD Wheels drives:24 mm hex for Losi 5IVE-T, HPI Baja 5 and MCD ccars.
Extremely flexible 6-piece body shell for Losi 5ive-T, with complete installation hardware.Made of thermoplastic elastomer (TPE), an extremely strong plastic which combines thermoplastic and elastomeric properties! Color
black (the decals pictured are not included!). The elastoplastic body set fits the stock Losi 5ive-T roll cage precisely and is almost "unbreakable"! Due to the special surface properties of TPE (elasto plastics), elasto decal sets are strongly recommended for TPE body shells.Of course, the extreme deformability of the elastoplastic body shell, compared to the stock version, is a huge advantage.And there's more with the elastoplastic body shell:Better dirt protection for the 5ive-T through partially closed wheel wells front and rear.Front and rear fenders with large cut-outs prevent contact with the tires.Integrated window nets allow for improved airflow and better engine cooling.The textured surface of the elastoplastic body shell is largely soil-resisting.Please note: This feature also makes the use of highly specialised adhesives for any kind of decals unavoidable if you want them to stay. All decals shown in the pictures for presentation are of the standard version!Even though the elastoplastic body shell is much tougher than the stock Losi 5ive-T body, the weight increase only very moderate from 902 grams to 971 grams. The body shell is a 6-piece design for best flexibility possible.Contents:1 x hood/front fender2 x side panels1 x roof2 x rear fenders1 x complete installation hardware
Customers also viewed
Extra wide tire mounted and glued on genuine 1/6 scale FG buggy silver rims 3105/02 with silver extension ring 3106!Diameter 165 mm, width 80 mm. Fits all FG and Carson largescale cars, may fit other cars with 18 mm wheel squares as well.Available in three different compounds:softhard Unit price:- Mammoth tires extra wide: EUR 47.20 / pair- Mammoth inserts extra wide: EUR 9.90 / pair- genuine FG wide track rims 3105/02: EUR 14.90 / pair- genuine FG rim extension rings 3106: EUR 14.90 / pair- mounting + glueing rims / extensions / inserts / tires: EUR 13.00Total: EUR 99.90 Priced per pair.We have tried various rubber / tire compounds for several months on various forms of terrain, etc.. The Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! The Mammoth is available in soft, medium and hard! The rule is: the harder the ground the softer the tire compound. Where other tires spin helplessly the Mammoth provides serious traction. With few exceptions, the Mammoth is usually for the rear axle only. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall. The disadvantage of Mammoth tires: Because of their extreme width they need to be mounted on FG wheels with extension rings and wide tire inserts (same as for the FG wide slicks), which is a labor intensive job. From experience, we must strongly recommend against using rims from another manufacturer in combination with extension rings. Due to the before mentioned traction no other rim has been up to the task! Broken rims and torn squares were the result. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.However, the original FG-rim lasts without problems!Also suitable for:With the following wheel adapter: y1183 Rim adapter
%
MadMax Monster tire LAND G-RIPPER 211x104 The off-road tire combination for extreme terrain use and "RC-car show use"! Glued on rims with 24 mm hex drive and reinforcement ring, suitable for Losi/HPI/Arrma/Traxxas/Carson1/5 series cars Dimensions: 211 mm outer diameter 104 mm width 875 grams weight Please note: Since the MadMax Monster LAND G-RIPPER tires give a very good grip, the rim and bonding are extremely stressed.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Here you can find the other tire sets shown in the picture: ARRMA ARA550061 Losi LOS45017/S Carson B501
You can select the tyre hardness above: - Hurrax HX100 extreme Grip Medium 175/70 mm tyre
and - Hurrax HX400 extreme Grip Soft 175/70 mm tyre Please select which tyre you prefer. You also have the option of having the tyres delivered ready glued for an additional charge. Please click if you want to have the tyres ready glued!
HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms
Genuine FG spare/option part. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Contents:2 pieces/1 pair
Genuine FG spare/option part. Completely new revised and in important details improved Mini Block Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant.The FG Mini Block tires are especially well-suited for slightly loose and humid ground.We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle.The Mini Block tires are also well-suited as front tires for 2WD models in combination with the Mini Pin tires on the rear axle.These tires are suitable for all 1:6 scale wheels with Ø110mm and a width of approx. 64mm.Suitable inserts are enclosed.Contents:2 pieces
Genuine FG spare/option part. The Maxi-Grip tire develops more road grip and has a better balanced driving performance on a very uneven ground according to its bigger tire diameter and the improved rubber mixture. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Diameter x width: 165 x 65 mmRim with 18 mm square driveContent:2 pieces
%
Genuine GPM spare/option part.Tires for a solid to medium terrain.Contents:2 pieces