145 products found for "kleb_0008"

rc-car-online - Home

y19281 HT Tire adhesive 4000, 1pce.

Item N° y19281 HT-tire adhesive 4000, 1pce.1 piece / 20 grammsHT-tire cement, specially formulated for rubber/plasticContent:20 gr bottle

Content: 20 Gramm (€345.00* / 1000 Gramm)

€6.90*

y19015 Bindulin Dichtfix (untill 180°!)

Bindulin liquid rubber - very high elasticitySuitable for additional sealing of tuned pipes and exhaust / manifold connections .Temperature resistant from -60 ° to + 180 ° CResistant against diluted acids.Also for sealing threaded joints, electric lines and cable lead-throughs in receiver boxes.The surfaces must be clean, grease free and dry (brake cleaner).Contents:1 piece / 45 grams

Content: 45 Gramm (€331.11* / 1000 Gramm)

€14.90*

y0115 Accellerator - 1pce.

For all tire adhesives above,15 ml pump spray bottleAccelerator-spray is the second component to cure superglue immediately.Advantages: Tangible adhesion after a few seconds Aromatic solvents and hexane free Suitable for hobby, craft, industry and household.Processing:Clean the surface thoroughly. Apply accelerator at room temperature on both surfaces to be bonded until a clear liquid film appears. Air out the applied accelerator, then apply the superglue as usual.

Content: 15 Milliliter (€593.33* / 1000 Milliliter)

€8.90*

y0807 MD-Sil RTV silicone sealer

Genuine MD spare/option part. The red version with a temperature resistant up to 300°C. Directions for use:Clean the surfaces with a cleaner. Apply MD-Sil on one side and press the parts together. Touch-dry in 10 - 20 minutes. Curing speed 3 mm/24 hours. Contents:1 piece / 80 ml

Content: 80 Milliliter (€211.25* / 1000 Milliliter)

€16.90*

GW71 - GRP 1:6 Buggy "BULDOG" Reifen ungeklebt, 2 St

grp_w71_ungeklebt Rubber compund: Extra Soft - GW71X

Item N° GW71 GRP 1:6 Buggy "BULDOG" Reifen ungeklebt, 2 St.Tires will be delivery with inlays and without rims. - Medium aggressive knobby tread - Good directional stability - Good lateral traction - Good propulsion - For solid surfacesTires are not glued!Tire diameter: 164 mmTire width: 61 mm

€32.40*

DYNC0008 EC3 connector, female

Genuine Dynamite spare/option part.Contents:2 pieces

€6.99*

E540008-L UFRC A-arm, front lower l/h

Genuine UFRC spare/option part. Fits Growler GX1.Contents:1 piece

€18.90*

E540008-R UFRC A-arm, front lower r/h

Genuine UFRC spare/option part. Fits Growler GX1.Contents:1 piece

€18.90*

10008 FG Formula 1 Competition 1/5

This model is fitted with numerous aluminium parts: front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Just like all other FG Competition models the FG Formula 1 Competition is the most successful model of the past years. The experiences we gained from numerous competitions have all influenced this version. The FG gearwheel drive which is extremely smooth running and cares for more power reserves. Surely FG Modellsport has created a competitive model for the next years with this version which will seamlessly follow up on the past successes. Highlights Alloy wishbones FG gearwheel drive Alloy rear axle plate FG alloy shock absorbers 04 Ball-bearing alloy servo saver 26 ccm Zenoah-Engine Airbox Tuned pipe Front- and rear brake 5 mm Chassis Lexan body shell Technical description of the FG Formula 1 Competition ki:The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition kitCNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.We deliver the models as a kit including mounting instruction. The body parts are made of clear polycarbonate for your own painting. FG stickers and writings are enclosed.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engine Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!

€2,499.95*

Configure now

HF0008 Toe adjusting block 4° right

€2.48* €4.95* (49.9% saved)

10008 FG Formula 1 Competition with hydraulic brake "special price"

Special offer price ! Including Mecatech Expert hydraulic brake on the front axle. Numerous aluminium parts such as front and rear bearings, damper linkage, engine mount, wishbone ends. Uniball steel ball joints, which allow all possible adjustments of the front and rear axle, gear drive, which ensures high reliability and optimum function. Like all FG Competition models, the Formula Competition from FG is the most successful model of recent years. The experience gained from the competitions has been incorporated into the latest version. With FG gear drive, which is extremely smooth-running and provides more power reserves. With this version, FG Modellsport has certainly created a competition-ready model for the years to come that will seamlessly build on past successes. Highlights Aluminium wishbones FG Gear drive Aluminium rear axle plate FG Adjustable aluminium shock absorbers Aluminium servo saver with ball bearings 26 cc Zenoah engine Airbox Resonance pipe system Mecha. rear disc brakes 5 mm chassis Lexan bodyworkAnother improvement is the hydraulic disc brake in the front wheels.Technical description of the FG Formula 1 Competition kit. The chassis of the FG Formula 1 Competition is built on a 5mm aluminium chassis and all screws at the bottom of the chassis are countersunk. The front and rear axle carriers as well as the engine unit are connected to each other over the entire length of the chassis, so that almost the rigidity of a monocoque chassis is achieved. The engine is fixed in place using a quick-release fastener, making it possible to change the engine quickly. The rear axle is driven by several smooth-running spur gears and an FG ball drive on the rear axle. The clutch bell is held by a separate flange bearing to reduce the load on the crankshaft. The front and rear axle with versatile adjustment options such as camber, caster, etc. consists of aluminium wishbones at the bottom. Sturdy aluminium rear axle plates reduce wear on the rear axle and provide enormous driving stability. Four oil-pressure shock absorbers, which are actuated via a push-rod suspension, and stabilisers ensure optimum ground contact.The model is powered by a powerful 26 cc engine with airbox and resonance silencer.The chassis is supplied with tuning bowden cable brakes for the rear axles.Equipment of the FG Formula 1 Competition kit 5 mm aluminium chassis, 26 cm³ engine, intake noise filter, tuning resonance silencer, FG gear drive, ball drive, complete rear axle and front axle carrier unit with integrated quick engine mounting, double aluminium wishbone mountings, aluminium triangular wishbones at the bottom of the rear axle and front axle, front and rear aluminium steering knuckles, ball bearing servo saver, steering stops, pushrods, 4 oil pressure shock absorbers with aluminium shock absorber pistons or mechanical tuning brakes at the front and rear. Servo saver, steering stops, pushrods, 4 oil pressure shock absorbers with aluminium shock absorber pistons or mechanical tuning brakes front and rear, anti-roll bar for front and rear axle, 10 mm aluminium balls, polycarbonate body, polyamide front spoiler, receiver box, competition tyres with tyre inserts. The models are supplied as a kit with assembly instructions. The body parts are made of crystal-clear polycarbonate for self-painting. FG stickers and lettering are included. To complete the models, you will also need: 1 remote control system (transmitter, receiver), 1 large servo for the steering (approx. 40 - 50 kg), 2 servos for throttle/brake (approx. 20 - 30 kg), batteries and charger. These parts are not included and must be ordered or delivered separately if installation is required!IncludetZenoah 26cc engineClear bodyshell and polycarbonate spoilerMechanical brakes rearHydr. brakes frontDimensionsLength: 960mmWidth: 440mmHeight: 230mmWheelbase: 620mmFormular 1 models in action!Drive:2WDMotorization:GasRTR:Without RTRScale:1/5

€2,599.00*

Configure now

Bowden cable bracket, Baja premium brake, 1 pce., y0008

€20.50*

HB0008 Brake shaft for 2 discs and ball bearing brake, 1 pce,

Original Hurrax replacement part made from stainless steel.

€4.98* €9.95* (49.95% saved)

Reifen geklebt

€12.00*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

6571 FG model decal

Genuine FG spare/option part. FG stickers such as FG Logo, Team FG Modellsport, FG ORIGINAL TUNING PARTS a.s.o. for light and dark model paintings. Suitable for all FG models.Content:2 sheets, 240 x 170 mm each

€11.90*

y3001 Light cover decals, set #2

Suitable for the lights on off-road cars like Losi 5ive-T or HPI Baja cars and also for embellishment of other body shells.Dimensions:Diameter: 32 mmContentt:Four teeth orange smiliesFour dead yellow smiliesFour red scullsFour green rc srokes

€4.90*

6225/06 FG Maxi-grip knobbed tires glued

Genuine FG spare/option part. The Maxi-Grip tire develops more road grip and has a better balanced driving performance on a very uneven ground according to its bigger tire diameter and the improved rubber mixture. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Diameter x width: 165 x 65 mmRim with 18 mm square driveContent:2 pieces

From €89.90*

Details

y1016/111 Starter decal G320RC

Genuine Zenoah spare/option part. Replacement part fits Zenoah G320RC.

€3.90*

6419/09 FG Slick tires rear S1/80mm 1:6 glued, 2 pcs.

Genuine FG spare/option part.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Measures:Diameter: 145 mmWidth: 80 mmRim with 18 mm square drive.

€118.95*

This product is currently not available.

6225/05 FG Super-grip knobbed tires glued

fg_6225_05 Version: 6225/05M FG Super-grip knobbed tires glued, medium

Genuine FG spare/option part. The FG Super-Grip tires are available in a medium or soft hardness compound. The Super-Grip tire develops more road grip and has a better balanced driving performance on a very uneven ground according to its bigger tire diameter and the improved rubber mixture. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Diameter x width: 165 x 65 mmRim with 18 mm square driveContent:2 pieces

€85.00*

6417/09 FG Slick tires S/63mm 1:6, glued, 2 pcs.

€107.95*

6228/07, FG Monster Truck tires M/ glued, 2 pcs.

These Monster tires have a bigger square depth, this reduces a cylindrical turning of the square wheel significantly. To mount these tires you need a 18 mm wide square wheel driver. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Durchmesser x Breite / diameter x width 210 x 115 mmAlso suitable for:With the following wheel adapter: y1183 Rim adapter

€115.95*

y0728/06 GRP tires sponsor decals

Sponsor decal set from GRP with five GRP lettering.Measures:Width: 150 mmLength: 140 mm

€4.90*

6163 HPI Servo Tape 20x100mm

Servo tape, simply that, tape for your servo and while this is an existing HPI Racing option part, you always seem to be bumming it off your friends. So it's time you stock up to repay debts in those field-service emergency fun situations.Contents:10 pieces

€5.99*

145 products found for "kleb_0008"

Filter products

rc-car-online - Home