8381/05 FG Tank venting valve, 1pce.
€12.90
Available
Product information "8381/05 FG Tank venting valve, 1pce."
Tank venting valve, 1pce.
Small handy vent valve for the fuel tank ventilation. Replaces the previously used vent hoses.
Login
Accessories / Spare parts
High quality flexible fuel line in your choice of blue, red, yellow, orange and green. Size:Length: approx. 1 meterOuter diameter: approx. 6.3 mmInner diameter: approx. 3.2 mmDiameters are 100% identical to the Zenoah Tygon hose #7352!
Customers also bought
Genuine Top Tuning spare/option part. Top Tuning The 20-amp Bigscale switch allows for a maximum input voltage of 30 volt. It is specifically designed as a receiver switch for use in combination with the Hitec HS-1005SGT servo and 4s receiver battery. The switch can also be used for other applications at your discretion with batteries up to 6S.Note: Top Tuning the electronic 20 amp Bigscale high voltage switch delivers the batterys full voltage. It does not replace a voltage regulator! The components which follow down the line (voltage regulator / servos / receiver) must be matched to this voltage! Using the latest MOSFET technology allows the 20 amp Bigscale high voltage switch to handle extreme loads, despite its small size. A blue LED status light clearly displays the activated mode. The 20 amp Bigscale high voltage switch is dust-and splash protected. He has an extremely low internal resistance and very low power consumption in off mode. Nevertheless it is recommended to unplug the battery when the model will not be used for an extended period. Properties:Voltage range: 3 to 30 VLoad: 20 ampsStandby consumption: 17 µAOperating temperature: - 15 ° C to +50 ° CCable length:Battery side 250 mmReceiver side 130 mmWeight: 13 gramsDimensions:Length: 29 mm Width: 13 mmHeight: 12 mmContents:1 piece
y0700 Double sided alloy servoarm: 9,90 EURy0700/01 Single-sided alloy servoarm: 7,90 EURy0701 Double sided split alloy servoarm: 14,90 EURy0701/01 Single-sided split alloy servoarm: 12,90 EURFor y0700, y0700/01, y0701 and y0701/01:Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaft Suitable for all servos with an output shaft with 25 teeth multi-tooth shaft, for example:y2006 Digital Big-Scale Servo D-21HVy2007 Digital large scale Brushless Servo CYS9130Nearly all Ribbe/Futaba servosMega Power servoThunder Tiger DS1015And many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarm are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.
Genuine FG spare/option part.This fuel cap tuning seal ensures a perfect seal of your fuel tank (items 8380/06, 8380/08 are not included).Drill with an 8 mm hole through the tank lid. Insert seal # 8384/02 into the neck of the lid.Insert seal # 8380/06 along with the aluminum cover with sealing ring into the plastic lid (# 8380/08).Tighten the complete assembly with the included nut, and finally add vent fitting # 8381/03.Reinstall the lid onto the tank.Content:1 set
The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!
Genuine Speed-Tec spare/option part. SPEED TEC tuning flywheel for Zenoah G230/240/260/270/290/320 and Chung Yang engines (includes HPI Fuelie and Losi).The weight reduced (210 vs. 230 grams) flywheel enables the engine to accelerate faster and rev higher. The optimal balancing guarantees better endurance at lower fuel consumption!A durability approval exists!Contents:1 piece
Marston Universal blue is the leading non-setting gasket and sealing compound in use world-wide. The product is used by many of the world?s major automotive manufacturers and by several Formula 1 teams.Features- Non hardening and non setting- Unlimited assembly time- Vibration resistant- Allows metal to metal contact- Resistant to combustion products, water, engine coolant, petroleum, lubricating oils, kerosene and fluorocarbon refrigerants- Seals surface imperfections- Withstands rapid variations in temperature80 ml tube
Content: 80 Milliliter (€123.75 / 1000 Milliliter)
Customers also viewed
Genuine FG spare/option part.Fits formula 1 cars only.
Genuine HT spare/option part.Small aluminum breather cap for easy installation at the end of the breather hose, common on many tanks. It allows ventilation of the tank and keeps dirt from entering the breather hose.Color: silverContents:1 piece
Genuine FG spare/option part. Very efficient tank venting also for high fuel temperatures, with each 1 valve for ventilation and aeration. Suitable for all fuel tanks of large scale models.
The safety fuel filling system is perfect for refueling all common fuel tanks and fits all common jerry cans up to 5 liters. The integrated ventilation of the fueling system allows a gurgling-free pouring. In addition, the automatic filling stop prevents fuel overflow and spillage.The environmentally friendly filling system reduces the escape of fuel vapors during and after refueling and thus protects against contamination. A union nut is included for exact positioning of the system at small tank openings. In addition, the filler is equipped with a retaining loop so that it can be securely attached to the jerry can.Safety Fuel Filling Systemno overflow and spillageThe automatic filling stop prevents overflow and spillage.Gurgling-free refuelingThanks to the integrated ventilation, gurgling-free refueling is possible at last and the escape of environmentally harmful fuel vapors is reduced.Integrated lid attachmentThe integrated lid fastening prevents loss, which is especially useful for mobile use.Lid lockingNo more losing the cap. Lid lock is directly connected to the can.VentilationGurgling-free refueling. Reduction of escape of environmentally harmful fuel vapors.Made in GermanyThe filling system is manufactured in Germany. Overview: Safety nozzle filling system for fuel With integrated ventilation for refueling without gurgling Reduction of escape of environmentally harmful fuel vapors Integrated automatic filling stop to prevent overflow and spillage With union nut for exact positioning of the system With captive screw connection Practical strap for attachment to the jerry can included Made in Germany Filling opening: ø inside = 29 mm, thread outside ø = 38 mm Nozzle: ø outside = 21 mm, length = 160 mm Material: Polyethylene (HD-PE) Color: black/red Content:1 x Safety fuel filling system
