6429/01 FG Upright front for 1:6 2WD models

€39.90*

Available

Product number: fg_6429_01

EAN: 3410564508442

Product information "6429/01 FG Upright front for 1:6 2WD models"

Genuine FG spare/option part.

Reinforced version with steel inlay to prevent the M5 bolts from being pulled out.

Bearing seats: 22 x 7 mm.

Contents:

2 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Alternatives

y0932 HT Alloy front uprights for FG / Smartech

Genuine FG spare/option part. Machined alloy front uprights with replaceable steering arm, accept 608 sized bearings (8 x 22 x 7 mm, stock size). Fits all FG (except 4wd models) and Carson / Smartech 2WD 1/5 and 1/6 cars.included in delivery contents:4 x M5 x mm screws8 x M3 x mm screws8 x M5 x mm washerFor installation in offroad cars you will need shorter steering rods 7028/01.Contents:2 pieces

€129.90*

Accessories / Spare parts

y0932 HT Alloy front uprights for FG / Smartech

€129.90*

Customers also bought

6722/30 FG Countersunk screw M5x30 mm, 10 pieces

Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Content:10 pieces

€5.50*

Details

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€47.90*

DYNE1240 Dynamite Large Scale Safety Kill Switch

Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece

€39.99*

Details

Carburetor Walbro WT 1107 with choke normal/ball-raced

Walbro Vergaser WT1107 with choke Standard carburetor for Zenoah G320. Typ: Walbro WT1107This is the stock carburetor used for the G320RC engine, and will also work on all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³. Dimensions:Bore: 15,88 mmVenturi: 13,5 mmIndependent tunable high and low speed jets.The carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³.

€79.90*

Configure now

FG TR4 Truggy 4WD HT-Edition

Ready for an extra portion driving fun? Then try the TR4 made by FG! Agressive appearance combined with the Leopard 4 chassis results in an optimal handling and stunning top speed with lots of driving fun wich will thrill you. Equipped with a 26 cm³ two-stroke gasoline engine with installed pull-start system. The TR4 is an uncomplicated complete package with well-tired racing technology.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical information:Strong 26 cm³ gasoline engineMaintenance friendly chassisTwo differential gearsHardened driving partsCompletely ball-bearedLarge-volume aluminium dampersAggressive rim designGrip tires with 185 mm diameter and 95 mm widthReady to use Off-Road filterSimple handlingLow weightPure driving funHT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURDriveshaft bootsProtect ball drive as well as cardan drive against dirt. 4 pairs / 8 piecesValue: 42,90 EURAlloy spur gear carrierUse for 46T - 48 teeth spur gears.Value: 39,90 EURTotal value: 200,30 EURDimensions: Length: 760 mm Width: 520 mm Height: 320 mm Wheelbase: 534 mm

€1,279.95*

Configure now

y04474 HT Rear upper alloy wishbone 2WD

Genuine HT spare/option part.Rear upper alloy wishbone with droop stop. Replacement for plastic wishbone FG 6074/02.Will also fit the following Carson/Smartech cars:Onroad chassis C5, Attack, Super Attack, Gas Blaster and TouaregCarson Comanche, Attack Evo, CRT + CPT when installedwith 75 mm turnbuckle y0988Comes with 2 M8 low height nuts included. Contents:2 pieces

€69.90*

Similar products

6431 FG Steel pinion 16 teeth

Genuine FG spare/option part.For combination with 48T main and differential spur gear.Diameter: 26.7 mmBore: 10 mmTotal width: 16 mmTooth width: 9.5 mmModule: m=1,5Contents:1 piece

€26.90*

6427 FG Plastic gear wheel 46 teeth - 1pce.

46 teeth gear wheel for the layshaft.Diameter 72 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

6432 FG Steel pinion 18 teeth - 1pce.

Item N° 6432 Steel pinion 18 teeth - 1pce.For combination with 46T main spur gear.Diameter 29,7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

€35.00*

Details

6431/01 FG Steel pinion 16 teeth, wide - 1pce.

Item N° 6431/01 Steel pinion 16 teeth, wide - 1pce.For use on the clutch bell of FG monster cars.Diameter 26.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

€33.90*

6441 FG Filter oil for foam filter 50ml

Genuine FG spare/option part. For use with all foam filters, not for fabric filters.Content1 piece

Content: 50 Milliliter (€198.00* / 1000 Milliliter)

€9.90*

Details

6425/01 FG Stabilizer front/rear for 1/6 scale models

Genuine FG spare/option part.Fits for all 1:6 scale models except Monster-Truck, Monster Beetle Pro and Stadium-Truck. Not suitable for all 4WD cars.Dimensions:Front: 3 mmRear: 4 mmContents:1 set

€37.00*

6433 FG Steel pinion 20 teeth - 1pce.

Item N° 6433 Steel pinion 20 teeth - 1pce.For combination with 44T main spur gear.Diameter 32.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

€37.00*

6451/04 FG O-rings for air filter adapter 19x1,5 und 57x2,5mm - 2pcs.

These air filter adapters are needed fpr mounting the FG air and inlet silencers 6464, 6465 and the K+N air filters 6442 and 6460 as well as 9462 and 6466 on Solo, Zenoah and Tech engines.

€3.90*

6432/01 FG Steel pinion 18 teeth 2-speed - 1pce.

Item N° 6432/01 Steel pinion 18 teeth 2-speed - 1pce.For combination with 46T main spur gear on 2-speed spur gear only.Diameter 29.7 mmBore 10 mmTotal width 16 mmTooth width 9.5 mmModule: m=1,5

€35.00*

6451/03 FG Air filter adapter for Zenoah and CY, 1 pce.

Item N° 6451/03 Air filter adapter for Zenoah and CY, 1pce.These air filter adapters are needed fpr mounting the FG air and inlet silencers 6464, 6465 and the K+N air filters 6442 and 6460 as well as 9462 and 6466 on Solo, Zenoah and Tech engines.Fits: Zenoah G230/G240/G260/G270/G290 and CY 23/26 cm³ engines.

€17.50*

6438/05 FG Tire insert for slicks 80 mm 1/6

Genuine FG spare/option part.Fits for 1/6 scale slick tires. Dimensions:Length: 380 mmWidth: 73 mmHeight: 13 mmContents:2 pieces

€14.90*

6432/17 FG Steel gearwheel 17 teeth, profile displaced, 1 pce.

Item N° 6432/17 Steel gearwheel 17 teeth, profile displaced, 1 pce. True running steel pinion for minimized wear. Suitable for all FG cars except Formula 1. Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn't really matter.

€33.90*

Details