Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.

Genuine HT spare/option part.Rear alloy damper plate with several adjustment possibilities of the shock absorbers. Replacement for FG plastic rear shock tower FG 7072/01Please note: When installing in combination with plastic diff mounts you should insert a-arms with hinge pins before bolting together rear plate and diff mounts.Content:1 pieces

Genuine HT spare/option part. Suitable for all FG 2WD and Smartech/Carson 2WD models except Evo 04/Competition 07/EVO 07 and Formula 1. Content:2 piece

Genuine FG spare/option part. The set will shipped without gear carrier plate. Contents:1 set

Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces

Genuine HT spare/option part.Gear protector for the bottom of the 2WD chassis plate. Replaces stock plastic part FG 6082 or Carson 32481.Contents:1 piece

Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (wishbone pin), too. Fits the rear axle of all FG offroad cars (2WD and 4WD) and all Carson / Smartech cars.Content:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm

Genuine HT spare/option part.Rear upper alloy wishbone with droop stop. Replacement for plastic wishbone FG 6074/02.Will also fit the following Carson/Smartech cars:Onroad chassis C5, Attack, Super Attack, Gas Blaster and TouaregCarson Comanche, Attack Evo, CRT + CPT when installedwith 75 mm turnbuckle y0988Comes with 2 M8 low height nuts included. Contents:2 pieces

Genuine FG spare/option part.Alloy rear axle mount right Leopard 2WD/4WD.

Genuine FG spare/option part.Replacement part for: 67360 Conversion kit for gear brake Leopard

Item N° 9473Ball drive set for Leopard Sportsline, setFits for 2WD/4WD Sportsline.Not suitable for front application on 4WD cars!

Alloy rear axle conversion kit for all FG 2WD 1/6 cars: Marder, Off-Road Buggy, Beetle, Race Truck and all FG Monster / Stadium models.The set includes:- rear plate- differential mounts- lower a-arms- upper a-arms- installation hardware.Please note: must use inge pins 6075 instead of 6073!

Genuine FG spare/option part.Spare part for the Leopard 2010 version.

Genuine HT spare/option part.Quick change clips for installation and de-installation without tools, galvanic zinc plated.Spring steel, hardened and tempered to 1450 to 1600 N/mm² tensile strength.Available for 4, 5 and 6 mm shafts.Contents:10 pieces

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces

Genuine FG spare/option part. The gear set is needed to convert the Leopard 2 and Leopard 4 Competition with 4 disk brakes to the lighter gear brake. According to the loss of brake and servo parts we achieved a weight reduction of approx. 350 grams.Content:1 set

Genuine HT spare/option part. Rear alloy uprights for 1:5 and 1:6 models and 4WD Porsche, CNC-cut, optimal fitting, non-twisting even by heat.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 20 mmContents:1 set

Item N° 6479/02Rear alloy 08 upright, right, 1 pce.Spare part for FG no. 6479.