TT1530/650 Top Tuning 5000 mAh LiPo battery 6S, 22.2V 60C Offer

Regular price: [ITEMPRICE]SELF[ENDITEMPRICE] EUROffer of the month price: [ITEMDISCOUNTPRICE]SELF[ENDITEMDISCOUNTPRICE] EURTypical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesFor LiPo batteries, the peak amp rate is usually twice the continuous crateCan be charged with 5C when time is criticalRecommended charge with 2CConnectors: EC5, XH-balancer. Spezification:Tension: 4S / 14,8VCapacity mAh: 5000Case: HartCable cross section: 12AWG/3,3Length +/- 5 mm: 137 mmWidth +/- 1,5 mm: 46 mmHeight: +/- 1,5 mm: 48 mmWeight +/- 10g: 548gCont. current: 60C (220A)Contents:1 piece

Regular price: [ITEMPRICE]SELF[ENDITEMPRICE] EUROffer of the month price: [ITEMDISCOUNTPRICE]SELF[ENDITEMDISCOUNTPRICE] EURTypical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesFor LiPo batteries, the peak amp rate is usually twice the continuous crateCan be charged with 3C when time is criticalRecommended charge with 2CConnectors: EC5, XH-balancer.Dimensions: Length +/- 5 mm: 138 mmWidth +/- 1,5 mm: 47 mmHeight: +/- 1,5 mm: 24,5 mmWeight +/- 10g: 254gContents:1 piece

Regular price: [ITEMPRICE]SELF[ENDITEMPRICE] EUROffer of the month price: [ITEMDISCOUNTPRICE]SELF[ENDITEMDISCOUNTPRICE] EURTypical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesFor LiPo batteries, the peak amp rate is usually twice the continuous crateMaximum charge with 2CConnectors: EC5, XH-balancer. Spezification:Tension: 6S / 22.2VCapacity mAh: 8000Case: SoftCable cross section: 10AWG/5.3Length +/- 5 mm: 165 mmWidth +/- 1,5 mm: 43 mmHeight: +/- 1,5 mm: 61 mmWeight +/- 10g: 960gCont. current: 40C (320A)Contents:1 piece

Regular price: [ITEMPRICE]SELF[ENDITEMPRICE] EUROffer of the month price: [ITEMDISCOUNTPRICE]SELF[ENDITEMDISCOUNTPRICE] EURTypical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesFor LiPo batteries, the peak amp rate is usually twice the continuous crateCan be charged with 5C when time is criticalRecommended charge with 2CConnectors: EC5, XH-balancer.Spezification:Tension: 4S / 14,8VCapacity mAh: 6500Case: HartCable cross section: 12AWG/3,3Length +/- 5 mm: 137 mmWidth +/- 1,5 mm: 46 mmHeight: +/- 1,5 mm: 48 mmWeight +/- 10g: 548gCont. current: 80C (220A)Contents:1 piece

Regular price: [ITEMPRICE]SELF[ENDITEMPRICE] EUROffer of the month price: [ITEMDISCOUNTPRICE]SELF[ENDITEMDISCOUNTPRICE] EURTypical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesFor LiPo batteries, the peak amp rate is usually twice the continuous crateCan be charged with 5C when time is criticalRecommended charge with 2 3C (max. 3C)Spezification:Tension: 3S / 11,1VCapacity mAh: 3300Case: SoftCable cross section: 12AWG/3,3Length +/- 5 mm: 135 mmWidth +/- 1,5 mm: 45 mmHeight: +/- 1,5 mm: 25 mmWeight +/- 10g: 300gCont. current: 60C (115,5A)Contents:1 piece

Regular price: [ITEMPRICE]SELF[ENDITEMPRICE] EUROffer of the month price: [ITEMDISCOUNTPRICE]SELF[ENDITEMDISCOUNTPRICE] EURTypical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesFor LiPo batteries, the peak amp rate is usually twice the continuous crateCan be charged with 5C when time is criticalRecommended charge with 2 3C (max. 3C)Spezification:Tension: 3S / 11,1VCapacity mAh: 3300Case: SoftCable cross section: 12AWG/3,3Length +/- 5 mm: 140 mmWidth +/- 1,5 mm: 43 mmHeight: +/- 1,5 mm: 19 mmWeight +/- 10g: 251gCont. current: 35C (115,5A)Connectors: T-Connector, XH-balancer. Battery color may vary!Contents:1 piece

Genuine Losi spare/option part. Contents:1 set

Genuine MadMax spare/option part.Losi and HPI foam tire inserts from can be used.The BIG DIGGER tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Dimensions:Outer diameter: 170 mmTyre width: 60 mmContents:2 pieces / 1 pair Some off-road tires knowledge can be found here!

With complete RTR equipment y1382 Original Maxi-Pin 1/6 offroad competition tire The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder comes with completely installed remote control. Just fuel up, start the engine and drive off.Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm

Genuine Carson spare/option part.- Diameter 155 mm - Width 60 mm Knobbly tyre glued on black rim with 18 mm square.  Contents:2 pieces

Fits 5ive-T 2.0 as well!Set includes:Hitec Servo HS-1100WPy1378 Dymond LiPo special high current receiver battery 14.8V/2400mAhy1306 - JETI-SBEC 6-42V voltage regulatory1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 - Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 - Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 - All steel linkage steering servo/servo saver applicationy1378 - LiPo special high current receiver battery 14.8V/2200mAhGenuine FG spare/option part. This battery is especially for use in vehicles which are equipped with the Hitec Servo HS-900SGS/HS-1000SGT/1005SGT/HS-1100WP for external high-voltage power supply. This battery comes with a Y-adaptor harness for two connectors, one each JST and Futaba/Universal connector. The JST connector is used for hooking up to the steering servo; the universal connector is used for the voltage regulator. The battery fits into the standard battery box of the Losi 5ive-T. Dimensions:Length: 110 mmWidth: 32 mmHeight: 33 mmWeight: 247 grConfiguration: 4S1pCurrent rating: 40C (66 A)Recommended charging current: up to 3C (2.2 A)XHP(XH) -balancer connector To increase the battery's life span it is recommended to use a charging current of approx. 0.8 A for the first three cycles.Contents:1 piecey1306 - Servo voltage regulatorThe switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piecey1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT Losi 5ive-TGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1309 - All steel linkage for Losi 5ive-T steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 pieceHitec Servo HS-1100WPGenuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece