ST-AN22 SPEED TEC AN - Expansion sealing gasket for ‚cylinder with two bolt 0,25mm
Product information "ST-AN22 SPEED TEC AN - Expansion sealing gasket for ‚cylinder with two bolt 0,25mm"
Genuine Speed-Tec spare/option part.
For Zenoah G230/G260
AN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels!
The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is e.g. possible to make up for irregularities in the sealed surfaces (e.g. cylinder / crankcase) and seal them properly!
The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine!
Technical data of the material in contact with fuel:
Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;
Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5
The SPEED TEC AN - expansion sealing gaskets are available in the following versions:
Contents:
For Zenoah G230/G260
AN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels!
The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is e.g. possible to make up for irregularities in the sealed surfaces (e.g. cylinder / crankcase) and seal them properly!
The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine!
Technical data of the material in contact with fuel:
Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;
Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5
The SPEED TEC AN - expansion sealing gaskets are available in the following versions:
- # ST-AN26V carburetor gasket 0,25/0,50 mm
- # ST-AN25I insulator gasket 0,25/0,50 mm
- # ST-AN24L air filter gasket 0,25/0,50 mm
- # ST-AN22 cylinder gasket, two bolt 0,25/0,50 mm
- # ST-AN42 cylinder gasket, four bolt 0,25/0,50 mm
- # ST-AN23G crank case gasket 0,25/0,50 mm
Contents:
- 1 piece
Login
Customers also bought
Genuine Mecatech spare/option part for the FW01.Content:1 piece
Genuine FG spare/option part.Width 0.8 mm.Hint for installation: The green dot on the ring goes towards the clutch side!Contents:1 piece
Cylinder-piston repair kit for Zenoah engine G230. Set includes the following parts:Cylinder, piston, piston ring, cylinder foot gasket, centering disks, piston pin clip.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealer
With a fresh design and innovative tread patterns for even higher performance. We are thrilled to present the 1:5 Supreme V4 – our revolutionary tire for the world of four-wheeled modeling. The new V4 aims to raise the bar in competitions and cater to the needs of drivers. It features a redesigned tread with new patterns meticulously crafted for enhanced performance. Let’s see its key features: Exceptional Grip: Advanced tread patterns for unparalleled traction on various asphalt conditions. Simplified Driving: Superior control for a smoother and more effective driving experience. Enhanced Durability: Thanks to the new tread design, the tire’s performance remains consistent even in longer sessions. Available in Three Different Compounds. Like all our products, the V4 is available in various compounds to accommodate different asphalt conditions: - Q01 – SuperSoft - Q03 – Soft - Q05 – MediumNote:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability.Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!Dimension:Outside diameter: approx. 116 mmWidth: approx. 65 mmRims: 18 mm square driveContents:2 piece
Genuine FG spare/option part. Suitable for hydraulic brakes with the order number 09540 and 09541.Contents:2 pieces
Customers also viewed
Genuine FG spare/option part. This stroke-up crankshaft changes the stroke from 28mm (standard) to 30mm. The crank-shaft fits the Zenoah engines G230, G240, G260, G270 and G290. No warranty can be provided for engines with modified crank-shaft.Contents:1 piece
Full set of gaskets for Zenoah G40, G270, G290, and 4-Bolt CY engines.Set includes:0.4 mm cylinder gasket (Zenoah stock thickness!)1 mm exhaust gasket0.5 mm crankcase gasket0.5 mm isolator gasket0.5 mm carburetor gasket
Because of the customised and complex production of the Mecatech FW 01, the lead time is currently 14 working days!The Mecatech FW01 is for sure the currently most innovative 1/5 race car designed for the dedicated and technically enthusiastic rc car driver.Everyone is enthusiastic about the perfectly fitting and precise workmanship at the highest level. Only high quality materials are used for the production.Since many years Mecatech is a well-know premium manufacturer of largescale hydraulic brakes or shocks and, as only a few may know, a technology expert for a number of Formula 1 racing teams!The Chassis Kit of the FW01 is particulary intended for "switchers" and "newcomers" and differs from the Basic kit in that the brakes and shock absorbers are already included in the Chassis Kit. Here is a list of the parts that are required for completion:brakes and shocks (Difference to Chassis Kit)DifferentialEngine Clutch, Airbox and tuned pipe systembody shell and tiresElectonic components such as servos, batteries and Remote controlStock gearing:Clutch pinion / spur gear: 36T / 64TLayshaft pinion / differential: 24T / 73T Currently the Mecatech FW01 is for sure the benchmark of the 1/5 scale racing scene! In the first year Markus Feldmann won with his FW01 1: 5 Mecatech on one of the world's finest and most demanding race track in Lostallo / SwitzerlandMecatech is multiple German, European and World Champion with the FW01 and as the last result:Markus Feldman wins the European Championship in Tourlaville/France. All top 5 positions went to drivers running a Mecatech FW01. 7 out of 10 finalists cars were Mecatech FW01.Although the fit of the Mecatech FW01 parts makes the assembly of the car a great experience, some of our customers want to use the expertise of our shop and wish their FW01 fully assembled and tuned in by us!The complete assembly of your FW01 by our workshop is possible for an additional charge. Please note that the costs of the full assembly with servos a.s.o. do not include the price of any rc-components. If you do not have a suitable radio system with servos and batteries as well as switch and charger, you have to take an additional EUR 800 to EUR 1,500 for this equipment into account. We will be happy to make you an appropriate offer. We always supply the latest version of the Mecatech FW01Included in the chassis kit:- All pinions- clutch bell- Coupling fixation- All parts and screws for mounting the enginenot included:- differential- Engine and linkage- body shell and spoilers- Airbox- clutch - engine- Electronics- Tires