Mielke 5185 Big Power muffler set for Losi 5ive-T/2.0 and Mini

The Samba 5ive T tuned pipe from the 1/5 world champion!At the 1/5 World Championship were place 1 to 10 (!) equipped with a samba tuned pipe system.A proof of competence without equal!BiG BELLY, special version for the 5ive-T / Monster Truck XL with engines up to 32 cm³ engine. Comes with complete hardware for installation.Top quality and optimized performance across the entire rpm range of your engine.

Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece

The Samba 5ive T tuned pipe from the 1/5 world champion!At the 1/5 World Championship were place 1 to 10 (!) equipped with a samba tuned pipe system.A proof of competence without equal!BiG BELLY, special version for the 5ive-T / Monster Truck XL with engines up to 32 cm³ engine. Comes with complete hardware for installation.Top quality and optimized performance across the entire rpm range of your engine.

Chrome-plated Jetpro tuning resonance pipe incl. mounting material for the Losi 5ive-T.  Suitable for Losi 5ive-T, (not 2.0 ).  Equipment and scope of delivery see photos.  1 piece

The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder is also available with completely installed remote control. Just fuel up, start the engine and drive off.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery For an additional charge you can also select the HT-EDITION above. A great tuning offer for your new FG Marder. The standard price for the individual parts is €227.35. These tuning parts not only look great, but they also make your model more reliable.HT-Edition?HT-Edition means: this version comes with a big set of spare / option parts included.Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.Value: 64,95 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURFeatures:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm

Genuine FG spare/option part. Contents:1 set

With DMC/EFRA homologation number #10-2014 as required for 1/5 races!Here we present the new muffler Tornado Turbo by M. Mielke. (Currently this is at the DMC for homologation.) This is a further stage of the 2013 silencer. Again It is a lightweight muffler made from 0.8 mm thick steel sheet. The design has greatly changed and the complete silencer moves more towards the vehicles center, which ensures benefits for the cars overall set-up. The performance was further improved. Distance from the rear tires (heat generation) has been increased as well.