MAKX024 GPM Aluminum servo saver with spring, 25T, with servo adapter frame, Arrma Kraton / Outcast 8S

€37.90*

Available

Product number: gpm_makx024

Product information "MAKX024 GPM Aluminum servo saver with spring, 25T, with servo adapter frame, Arrma Kraton / Outcast 8S"

Genuine GPM spare/option part.

Servo saver machined from 6061 T6 aluminum by GPM for Kraton / Outcast 8S. Much stronger than the stock plastic part. The splined section for installation on the servo is machined from 7075 aluminum for increased strength.
Fits servos with 25T spline shaft.

Comes with a 6061 aluminum adapter frame for installation of a small steering servo (40/20/20 size).

Note: due to the replacement of standard servo, the center point of servo is slightly offset, so the length of the servo linkage needs to be adjusted.

Contents:

1 set

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Kunden haben auch gesehen

MAKX024N GPM Aluminum servo saver with spring, 25T, with servo adapter frame, Arrma Kraton / Outcast 8S

Genuine GPM spare/option part. Servo saver machined from 7075 T6 aluminum by GPM for Kraton / Outcast 8S. Much stronger than the stock plastic part.Fits servos with 25T spline shaft.Comes with a 6061 aluminum adapter frame for installation of a small steering servo (40/20/20 size).Note: due to the replacement of standard servo, the center point of servo is slightly offset, so the length of the servo linkage needs to be adjusted.Contents:1 set

€44.90*

ARA320553/01 ARRMA Receiver Box for original servo for Kraton / Outcast 8S

Genuine ARRMA spare/option part. Contents:1 set

€19.90*

67565 FG Front lower plastic wishbone, Leopard, 2pcs.

Item N° 67565Front lower plastic wishbone, Leopard, 2pcs.Spare part for Sportsline Leopard 4WD.

€28.50*

ST-AN26V SPEED TEC 0,25/0.50 mm carburetor AN - expansion sealing gasket

Genuine Speed-Tec spare/option part. For Zenoah G230/G240/G260/G270/G290/G320AN - expansion sealing gaskets are in use in the 2-stroke motor sports for years and are based on NBR-linked cellulose fibers. They are especially used for sealing hot oils, greases and fuels! The sealing material is compressed during assembly, and as soon as it comes into contact with fuel, it swells again. Thus it is i.e. possible to make up for irregularities in the sealed surfaces (i.e. cylinder / crankcase) and seal them properly! The material of the SPEED TEC AN - expansion sealing gaskets guarantees a very good dimensional accuracy and is often the solution for leaks on your engine! Technical data of the material in contact with fuel:- Rebound ASTM G > 30%; increase in thickness < 5%; weight gain < 55%;- Compressibility ASTM F36 G 22.5% +/- 2.5 27.5% +/- 7.5 The SPEED TEC AN - expansion sealing gaskets are available in the following versions:# ST-AN26V carburetor gasket 0,25/0,50 mm# ST-AN25I insulator gasket 0,25/0,50 mm# ST-AN24L air filter gasket 0,25/0,50 mm# ST-AN22 cylinder gasket, two bolt 0,25/0,50 mm# ST-AN42 cylinder gasket, four bolt 0,25/0,50 mm# ST-AN23G crank case gasket 0,25/0,50 mmContents:1 piece

€4.40*

FG Challenge Line 530 BMW M4 with 26 cm³ FG engine

With this robust and reliable FG chassis, which is equipped with a powerful 26 cm³ combustion engine, you get the ideal entry into the fascinating "royal class" of large scale RC models as well as into the competition.The model has a 530 wheelbase. The models are built on a 4 mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in.Further equipment points are differential gear, 24 teeth steel pinion, oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings.The remote control, the two servos and the receiver battery (RTR set!) are required to operate the FG model. This RTR equipment is available in our shop selection for an additional fee.The body shell is clear, but also available in a painted version in our shop selection for an additional fee.Thanks to the numerous available option parts, you can upgrade your FG Challenge Line as required.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 890 mmWidth: 392 mmHeight: 240 mmWheelbase: 530 mm

€849.90*

Configure now

ARAC3144 ARRMA Ball Bearing 6x12x4mm for Kraton / Outcast 8S

Genuine ARRMA spare/option part. Contents:2 pieces

€5.99*