LOS252119 Losi Front CVD Assembly, 5mm Pin for DBXL-E 2.0

€49.99*

Prices incl. VAT plus shipping costs

Currently unavailable

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Product number: losi_los252119

EAN: 4058575124009

Product information "LOS252119 Losi Front CVD Assembly, 5mm Pin for DBXL-E 2.0"

Genuine Losi spare/option part.

Contents:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also viewed

LOS252125 Losi Universal Rebuild Kit, 4,6mm Pin, DBXL-E 2.0

Genuine Losi spare/option part. Contents:2 pieces

€9.99*

Details

7800 FG Zenoah G290RC with Walbro carburetor WT 990

Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5cm³ cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€284.90*

6104/05 FG Front driving axle M8

Genuine FG spare/option part. Reinforced front drive axle from M6 to M8 thread. Suitable for all 2WD Buggy models. For mounting the self-locking wheel nuts M8 Item No. 6115 are necessary.Length: 60 mm.Contents:1 piece

€11.90*

LOS252019 Front Center Driveshaft Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 piece

€59.99*

LOS252047 Losi CV rear Dogbone MTXL

Genuine Losi spare/option part.Contents:2 pieces

€49.99*

LOSB5900 Losi Steering Linkage Set 5T

Genuine Losi spare/option part. Contents:1 set

€29.99*

LOS254005 Losi Uprights Carriers/Spindles/Hubs Losi DBXL+MTXL 1/5 4WD

Genuine Losi spare/option part. Contents:1 set

€39.99*