Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum center diff mount; fits Losi DBXL 2.0.4-piece set consisting of two diff towers, connecting bridge, and pinion cover. Considerably stiffer than the standard plastic parts and unaffected by the heat generated by the engine and the brake.Contents:1 piece

Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum clutch bell holder for Losi DBXL+MTXL. Compared to the stock plastic part the higher strength of the aluminum part ensures secure seat for the bearings, increased dimensional stability at high temperatures and reduced operating temperatures for the bearings due the aluminums thermal conductivity. Larger bearings (12 x 28 x 7) for higher load capacity. Comes with ball bearings and spacer tubes included.It is recommended to use the ball bearings/bushings adhesive (y0113 Thread locking compound).Contents:1 set

Genuine HT spare/option part. Fits Losi Desert Buggy XL stock shocks.The Desert Buggy XL stock springs use a high preload, which is even bigger than the shocks travel. This means that the stock spring action increases not that much going through the available suspension travel. To handle hard impacts high viscosity oil is used in the shocks; however, this oil is too heavy for these springs for a proper rebound. A sensible suspension tuning becomes much pretty difficult.For this reason, the tuning springs Dirt-Spring Desert Buggy XL are shorter than the stock springs, but also use heavier gauge wire in return. Therefore the change in spring action during the suspension travel is noticeably higher than the preload; the suspension settings can be influenced more effectively.Due to their different characteristics the stock springs are difficult to be sorted among the line of the tuning springs.As a rule of thumb theyre similar to the 2.7 mm version when used with the current 2000 viscosity oil factory fill.Dimensions:Inner diameter: 35 mmFree length: 110 mmNumber of turns: 9Versions:y1388/01 - 2,5 x 110 mm Ochery1388/02 - 2,6 x 110 mm Bluey1388/03 - 2,7 x 110 mm Greeny1388/04 - 2,8 x 110 mm Silvery1388/06 - 3,0 x 110 mm Goldpair

Item N° GWH79 GRP 1:6 Buggy "GRIP" tire glued, 2 pcs.very aggressive bold x-pattern treadmoderate directional stabilityvery good lateral tractionvery good propulsionfor really loose surfacesTire diameter: 164 mm Tire width: 61 mmDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Attention:On all 2WD cars (except Leopard 2WD) the front suspension must be equipped with the combination of uprights y0932 and steering rods FG #7028/01. Wheel squares FG #6107/02 must be used in front and rear. 4WD cars must only use the wheel squares FG #6107/02 in front and rear.

Genuine HT spare/option part. Gas-nitrited tuning clutch bell with black oxide coating, machined from high grade. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well. This clutch bell is dimensionally identical to the stock part. Heat treatment and the use of a high grade material guarantee long service life.Due to a special heat treatment the clutch bell surface is shaded; this does not effect the function, but ensures great durability.Contents:1 piece

Genuine UFRC spare/option part. Original equipment tires of the Ghost Rabbit GR1.Fits Losi MTXL as well.When using our special wheel nuts TT1020/02 these tires can also be mounted on the Traxxas X-Maxx.Tire with vulcanized Kevlar belt, speed resistant (no ballooning) and yet flexible.Rim with steel hex insert.Diameter 230 mm, width 100 mm, 24 mm hex wheel drive.Rim thickness at center hole: 8.75 mm.Hex depth: 8 mm.Weight: approx. 2160 grams/pairOn the Losi DBXL running these wheels requires the installation of the DBXL024 ATOP axle extenders!Contents:2 pieces

Genuine HT spare/option part. Aluminum engine mount for Losi DBXL with reinforced threads due to separate threaded inserts. The steel inserts are set with thread locking compound and feature a flange on the top side for an absolute secure fit.A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.The original screws can be re-used.Contents:1 piece