AREA-5T-018 Aluminum spring perches Losi 5ive-T/2.0/B and Mini

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP.Protects chassis plate and transmission case over rough terrain. Also reinforces the chassis plates narrow section in front of the gear case. Thickness: 4 mm, weight: complete 141 grams.Contents:1 set

Genuine HT spare/option part. Ball & socket tool with t-handle, special version for the ball joints.Fits Losi 5ive-T. 5ive-B, Desert Buggy XL, Desert Buggy XL-E, Monster Truck XL and the HPI Baja 5B and Baja 5R Ford Mustang.Contents:1 piece

Genuine ATOP spare/option part. CNC-machined from 6061-T6 aluminum by ATOP.Complete with all required hardware.Contents:1 piece

Genuine ATOP spare/option part. CNC-machined from 6061-T6 aluminum by Area RC.The big advantage over the stock plastic part is its temperature insensitivity. While the plastic case loses its strength with increasing temperatures and may finally disintegrate, the aluminum case stays intact.The one-piece design guarantees a true running and leak-free case. Steel bushing for drive cup shaft and O-ring.Fits front, center and rear applications on all Losi 5ive versions and Mini!Contents:1 piece

Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC, increase track width for 25 mm and allow for the use of HPI 5T, Losi 5ive-T, 5ive-B and Mini rims. 5 mm o-rings protect against drive pin loss. Set of four inclusive o-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set

For sealing the axles on Losi 5ive-T and Mini cars, keeps debris out of the inner screws which secure the retainer pin. Set of 4 or set of 10 to choice.Can be used for Losi 5ive-T, Mini and HPI Baja cars.

Genuine FG spare/option part.CNC-machined from 6061-T6 aluminum by Area RC.Contents:2 piece

Genuine ATOP spare/option part. Upper front camber rods with guide bushing set and with pivoted steel ball joints right/left thread and locknuts for Losi 5ive-T. Balls with 6 mm hole, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 130 mm. Contents:2 pieces

Genuine FG spare/option part.CNC-machined from 6061-T6 aluminum by Atop RC. Contents:2 piece

Genuine Area spare/option part for set AREA 5T-008. Contents:2 pieces

Genuine ATOP spare/option part. CNC-machined from 6061-T6 aluminum by ATOP.New improved designs combines increased strength with reduced weight. Both together give a total weight of 130 grams.Contents:2 pieces

Genuine ATOP spare/option part.ATOP tie rod set with guide bushing set and with steel ball joints and turnbuckle center piece with locknuts for Losi 5ive-T.Balls with 6 mm bore diameter, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 134 mm.Contents:2 pieces

Genuine FG spare/option part.CNC-machined from 6061-T6 aluminum by Area RC.Contents:2 piece

Genuine FG spare/option part.CNC-machined from 6061-T6 aluminum by Atop RC. Contents:2 piece

This genuine factory painted Losi 5ive-T body shell set with decals .New version of the 5ive-T body shell with scoop on the hood for optimized cooling!The set includes the following genuine parts (unit parts only clear available!): LOS350005 Front sectionLOSB8102 Center sectionLOSB8103 l/h rear fender with plateLOSB8104 r/h rear fender with plateLOS259003 Vehicle decalwith factory paint job on all body parts and decals applied. Delivery without roll cage!

Fits 5ive-T 2.0 as well!Set includes:Hitec Servo HS-1100WPy1378 Dymond LiPo special high current receiver battery 14.8V/2400mAhy1306 - JETI-SBEC 6-42V voltage regulatory1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/01 - Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1308/02 - Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WPy1309 - All steel linkage steering servo/servo saver applicationy1378 - LiPo special high current receiver battery 14.8V/2200mAhGenuine FG spare/option part. This battery is especially for use in vehicles which are equipped with the Hitec Servo HS-900SGS/HS-1000SGT/1005SGT/HS-1100WP for external high-voltage power supply. This battery comes with a Y-adaptor harness for two connectors, one each JST and Futaba/Universal connector. The JST connector is used for hooking up to the steering servo; the universal connector is used for the voltage regulator. The battery fits into the standard battery box of the Losi 5ive-T. Dimensions:Length: 110 mmWidth: 32 mmHeight: 33 mmWeight: 247 grConfiguration: 4S1pCurrent rating: 40C (66 A)Recommended charging current: up to 3C (2.2 A)XHP(XH) -balancer connector To increase the battery's life span it is recommended to use a charging current of approx. 0.8 A for the first three cycles.Contents:1 piecey1306 - Servo voltage regulatorThe switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piecey1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT Losi 5ive-TGenuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piecey1309 - All steel linkage for Losi 5ive-T steering servo/servo saver applicationGenuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 pieceHitec Servo HS-1100WPGenuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece

Genuine Losi spare/option part.Fits Losi 5ive-T, TLR 5ive-B and 5ive Mini.