Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

7902 FG Electric engine 1300KV Brushless

Product information "7902 FG Electric engine 1300KV Brushless"

Genuine FG spare/option part.

Technical data:
  • 4.000W 14,8V (4S) Maxi: 193A
  • RPM maxi: 30.000 rpm
  • Dimensions: 82 x 58 mm
  • Axle: 30 x 8mm
    Weight: 880g


Content:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Accessories / Spare parts

Average rating of 0 out of 5 stars

TT1021/07 Top Tuning electric Motor pinion nitrided hardened, 8 mm bore, module 1.5
Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece

€27.90*

Average rating of 0 out of 5 stars

7908 FG Y cable with gold connectors plug/socket 8 mm
Genuine FG spare/option part. For connecting the 200A brushless controller to one or two LiPo batteries.Gold plated 8 mm diameter connectors.Content:2 pieces

€17.90*

Customers also viewed

Average rating of 0 out of 5 stars

TT1021/07 Top Tuning electric Motor pinion nitrided hardened, 8 mm bore, module 1.5
tt_tt1021_07 Version: TT1021/07A - Type A with 15 teeth
Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece

€27.90*

Average rating of 0 out of 5 stars

670070E FG Fun Cross Sport E 2WD with brushless engine and brushless controll 150A
Genuine FG spare/option part.In the first place our 1:6 Off-Road Buggy stands for driving fun. Through the knobbed tires or with Slick tires (optional extras) the model can be driven cross-country, on a car park, simply just everywhere.You can select the car with complete RTR-equipment from the options menu. RTR equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. 2WD Off Road BuggyMachined 4 mm aluminum chassis plate with side guardsIndependent suspension with many options for adjustmentBig bore shocks with adjustable stop. Ball raced steel drive trainRoll cage, can be used as a carrying handle as wellClosed factory painted polycarbonate body shell with decals already applied, nylon wing with adjuatable angleFlange rims with mounted and glued knobby tiresBrushless motor150A brushless controlTwo locations for the batteries with hook-and-loop strapsDimensions:Length: 770 mmWidth: 465 mmHeight: 300 mmWheelbase: 535 mmWeight: 8.2 kgContent:1 piece

€799.95*

Average rating of 0 out of 5 stars

HW3010420 Hobbywing Ezrun MAX5 HV G2 ESC 250 A, 6-12s LiPo, BEC 8A
The EzRun MAX5 HV G2 is an impressive brushless controller with high-voltage capability. With support for up to 12S LiPo and a maximum output current of 250A, it delivers explosive performance and outstanding linearity. Thanks to intelligent freewheel technology, the speed control remains relaxed and cool even during demanding driving manoeuvres.  This controller is protected against water and dust in accordance with the IP 67 standard. As a result, the MAX5 HV G2 is naturally suitable for use in all weather conditions and can be operated on various surfaces such as mud, sand, ice, snow and water without damaging the power unit. With a powerful integrated BEC, an anti-spark design and multi-directional protection, this controller offers advanced features and high safety. The EzRun MAX5 HV G2 is the ideal choice for RC enthusiasts looking for maximum potential and reliability. By recording and storing real-time data, the operating status can even be monitored. And the upgrade of the sensor cable interface greatly improves the protection and waterproof performance of the controller. With perfect compatibility with Hobbywing's EzRun 56118 SD G2 motor, this power system offers an unbeatable team for optimum performance and protection against overheating.Features - Now with even more power than its predecessor. - Water & dust proof for use in all weather conditions. - Built-in ultra-powerful switching mode BEC to drive a wide range of servos (high power / high voltage servo). - Turbo timing setting included. Especially recommended with the matching motor (e.g. EZRUN 56118SD G2). - Several protective functions: Battery undervoltage protection, controller and motor overheating protection, signal loss protection, current protection. - Supports LED programme card, LCD G2 programme box and the OTA programming module for easier setting of controller parameters. - Data logging function to display various running data in the HW LINK app using the OTA Bluetooth module. - Supports controller firmware upgrade (multifunction LCD-G2 programme box or OTA programming module required for purchase). - Capacitor capacity increased by 45%. - 12 adjustable parameters.technical Data :Type: 1/5 Brushless Sensored Current (continuous/short): 250A / 1600A Input voltage: 6-12S LiPo BEC: 6V/7.4V/8.4V @8A (switch mode) Motor types: Brushless motors (with/without sensor) Motor limits: - 8S Lipo: KV <= 1200 - 12S Lipo: KV <= 800 56118 motor Fan: Yes, operated via the BEC Programming: LED programming card LCD programming box (G2) OTA programming module Separate programming connection Waterproof: Yes Output: 8.00mm Bullet Connector (female) Size: 94.5x59.4x50.9mm Weight: 428.5g Applications: 1/5 buggy, truck Scope of delivery:  Ezrun MAX5 HV G2 ESC

€209.95*

Average rating of 0 out of 5 stars

194100E Challenge Line 2WD 530E
Genuine FG spare/option part. The following items are required for completion: electric motor, ESC, steering servo, radio system, body mounts, body, LiPo driving batteries and charger.The models are built on a 4mm aluminium chassis with double wishbones front and rear. All borings are countersunk. Fully adjustable front and rear double wishbone suspensions.Further equipment points are: differential gear, oil-pressure shock absorbers with volume control and external, adjusting ring for the initial tension of the spring. All rotating parts on ball bearings.Tires are glued on the rims.

€569.95*

Average rating of 0 out of 5 stars

y1613 Mammoth Supergrip mounted and glued on silver FG rims
y1613 Version: Version
Genuine rc-car-online spare/option part.The optimal parking lot or race tires for your FG Racetruck model.Type Width Outer diameterFront 64 mm 153 mmRear 78 mm 153 mmGlued on original FG-Racetruck rims (rear tire with extension to the inside), incl. foam rubber insert,FG rim with 18 mm square drive and reinforcement ring.Attention: From experience we warn against using rims and extensions from another manufacturer.Since the Mammoth tires provide a very good grip, the rim and bonding are extremely stressed. Due to the high torque load in relation to the bonding of tires on large models, an occasional check in this regard and possibly a repair of the bonding (y0067) is inevitable.As a recommendation:The dirtier the track or the colder the temperature, the softer the rear tire should be.Reference for the front tire: With 2WD models this should be one to two stages harder than the used rear tire. On 4WD models, a tire combination with the same shore hardness front and rear is often good to drive.Of course, with Mammoth Supergrip Racetruck tires, the softer the tire, the higher the wear.The Mammoth Supergrip Racetruck tires have a special onroad tread. Whereby these still have an optimal grip after the wear of the tread, and can still be driven for a long time.

€89.90*

Average rating of 0 out of 5 stars

HW30105100 Hobbywing Ezrun MAX6 G2 sensored ESC 200 Amp, 3-8s LiPo, BEC 8A
The EzRun MAX6 G2 is a modern brushless controller with high-voltage support and an integrated Bluetooth module. Compared to its predecessor model, the second generation is considerably more powerful with up to 200A and, with 12 programmable parameters, also offers more scope for customisation to suit your personal driving style. Aggressive starts, high acceleration on straight stretches and jump control are just a fraction of what the controller has to offer. And thanks to the intelligent freewheel technology, the controller remains relaxed and cool even during these demanding manoeuvres. Probably the most convincing feature of the MAX6 G2 controller is the integrated Bluetooth module. This eliminates the need for programming cards and the OTA module as additional accessories. All you need now is the HWLink2 app and the controller can be conveniently programmed and updated on your smartphone. It is even possible to record data for up to 10 minutes and provides an insight into the most important driving data such as speed, voltage and temperature. With a powerful integrated BEC, an anti-spark design and several protective devices, this speed controller offers advanced functions and a high level of safety. The EzRun MAX6 G2 is therefore the ideal choice for RC enthusiasts looking for maximum potential and the best reliability. With perfect compatibility with both Hobbywing's EzRun 4990 G2 and 5690 G2 motors, this power system offers an unbeatable team for optimum performance with modern features. Features  - Now with even more power than its predecessor. - Integrated Bluetooth module to programme the controller directly via the HWLink2 app on your smartphone. - Intelligent fan that only activates when the temperature reaches a certain value. Water & dust resistant to IP67 standard for use in all weather conditions. - Built-in ultra-strong switching mode BEC to address a wide range of servos (high power / high voltage servo). - Turbo timing setting included. - Especially recommended with the matching motor (e.g. EZRUN 4990 G2 or 5690 G2). - Several protective functions: Battery undervoltage protection, controller and motor overheating protection, signal loss protection, current protection. - Built-in data logging function to display various running data of up to 10min in the HW LINK app - Supports firmware upgrade of the controller. - 12 adjustable parameters.Technical Data  Type: 1/6 Brushless Sensored Current (continuous/short): 200A / 1200A Input voltage: 3-8S LiPo BEC: 6V/7.4V/8.4V @8A (switch mode) Motor types: Brushless motors (with/without sensor) Motor limits: - 6S Lipo: KV <= 2400 - 8S Lipo: KV <= 1700 4990/5690 motor Fan: Yes, operated via the BEC Programming: HWLink2 app (via the integrated Bluetooth module) Waterproof: Yes Size: 70x56x45.5mm Weight: 245g Applications: 1/6, 1/7 on-road, truck, monster truck Scope of delivery:  Ezrun MAX6 HV G2 ESC

€149.00*

Average rating of 0 out of 5 stars

Mecatech FW01 Touring car, wheelbase 530 mm, Basic Kit -- Europe- and world champion
Because of the customised and complex production of the Mecatech FW 01, the lead time is currently 20 working days!The Mecatech FW01 is for sure the currently most innovative 1/5 race car designed for the dedicated and technically enthusiastic rc car driver.Everyone is enthusiastic about the perfectly fitting and precise workmanship at the highest level. Only high quality materials are used for the production.Since many years Mecatech is a well-know premium manufacturer of largescale hydraulic brakes or shocks and, as only a few may know, a technology expert for a number of Formula 1 racing teams!The Basic Kit of the FW01 is especially intended for "switchers" and differs from the chassis kit in terms of the brakes and shock absorbers (included in the chassis kit). Here is a list of the parts that are required for completion:brakes, shocks and springs (Difference to Chassis Kit)DifferentialEngine Clutch, Airbox and tuned pipe systembody shell and tiresElectonic components such as servos, batteries and Remote controlStock gearing:Clutch pinion / spur gear: 36T / 64TLayshaft pinion / differential: 24T / 73TCurrently the Mecatech FW01 is for sure the benchmark of the 1/5 scale racing scene! In the first year Markus Feldmann won with his FW01 1: 5 Mecatech on one of the world's finest and most demanding race track in Lostallo / SwitzerlandMecatech is multiple German, European and World Champion with the FW01 and as the last result:Markus Feldman wins the European Championship in Tourlaville/France. All top 5 positions went to drivers running a Mecatech FW01. 7 out of 10 finalists cars were Mecatech FW01.Although the fit of the Mecatech FW01 parts makes the assembly of the car a great experience, some of our customers want to use the expertise of our shop and wish their FW01 fully assembled and tuned in by us!The complete assembly of your FW01 by our workshop is possible for an additional charge. Please note that the costs of the full assembly with servos a.s.o. do not include the price of any rc-components. If you do not have a suitable radio system with servos and batteries as well as switch and charger, you have to take an additional EUR 800 to EUR 1,500 for this equipment into account. We will be happy to make you an appropriate offer. We are currently waiting for the latest version of the Mecatech FW01.Included in the basic kit:- All pinions- clutch bell- Coupling fixation- All parts and screws for mounting the engineDoes not include- Brakes, shocks and springs- differential- clutch- body and spoilers- Airbox- Engine and linkage- Electronics- Tires

€1,862.00*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Theme Development