7432/25 FG Steel gearwheel hardened 25 teeth

€34.50*

Prices incl. VAT plus shipping costs

Available

Product number: fg_7432_25

EAN: 3410564518328

Product information "7432/25 FG Steel gearwheel hardened 25 teeth"

Suitable for 39, 40 and 41 teeth main gear wheel.

Measures:

Diameter: 38,7 mm
Bore: 10 mm
Total width: 18 mm
Tooth width: 11,5 mm
Module: m=1.5

Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn't really matter.

Content:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

HT-Nitrited steel pinions for all FG and 1/5 scale Carson / Smartech C5

Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)Pinions up to 16T can be used on the layshaft as well.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Teeth:Item no.:13 Teeth HT y026814 Teeth FG 604614 to 48 Teeth HT y011615 to 48 Teeth FG 604715 to 48 Teeth HT y19354 wide16 to 48 Teeth FG 643116 to 48 Teeth FG 6431/1 wide17 to 48 Teeth HT y19355-116 to 46 Teeth HT y011917 to 46 Teeth HT y1935518 to 46 Teeth FG 643219 to 46 Teeth HT y1935718 to 44 Teeth HT y012319 to 44 Teeth FG 6432/220 to 44 Teeth FG 643321 to 44 Teeth HT y1935820 to 42 Teeth HT y090421 to 42 Teeth FG 7431/2122 to 42 Teeth FG 743121 to 40 Teeth FG 7432/2122 to 40 Teeth FG 7432/2223 to 40 Teeth FG 7432/2324 to 40 Teeth FG 743225 to 40 Teeth FG 7432/2526 to 40 Teeth HT y1936426 to 38 Teeth FG 7433Contents:1 piece

€29.90*

Configure now

y6479 HT rear alloy upright

Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces

€89.90*

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€54.90*

Details

%

6431/01 FG Steel pinion 16 teeth, wide - 1pce.

Item N° 6431/01 Steel pinion 16 teeth, wide - 1pce.For use on the clutch bell of FG monster cars.Diameter 26.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

€32.49* €33.90* (4.16% saved)

6047/01 FG Steel pinion 15 teeth wide, 4WD

Genuine FG spare/option part. True running steel pinion for minimized wear. Application: All FG cars except Formula 1.Dimensions:Diameter: 26,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11.5 mmModule: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Contents:1 piece

€31.50*

Customers also viewed

P-R-M 1000-40/01 Epoxy brake disk for Mecatech

PRM premium quality epoxy brake discs Material thickness is reduced for 0.1 mm to absorb tire debris or dirt easier!Dimensions: Outer diameter: 64 mmSocket size: 18 mm (square)Material thickness: 1,8 mm Suitable for:3002 Crosshydro hydraulic brake1001 Mecatech twin piston hydraulic brakeContent:2 Pieces

€22.90*

y0204 HT-Steel pinion extreme duty

zahn_0002 Size: y0204 - 12 Teeth

Genuine HT spare/option part.Coarse pitch pinion for the layshaft, especially for use in off-road and monster models. The teeth are stronger and , due to their bigger size, a little bit more forgiving when the gear mesh is not adjusted correctly.Fits FG cars and Carson Attack/Firehammer/Smartech Traveller, Carson Comanche, Touareg a.s.o.Fits FG and Smartech / Carson cars. Only for use with the extreme duty differential ring gear! Module: m=1,75.Contents:1 piece [INCLUDE]profilverschoben[ENDINCLUDE]

€28.90*

6104/05 FG Front driving axle M8

Genuine FG spare/option part. Reinforced front drive axle from M6 to M8 thread. Suitable for all 2WD Buggy models. For mounting the self-locking wheel nuts M8 Item No. 6115 are necessary.Length: 60 mm.Contents:1 piece

€11.90*

7450 FG 2-speed gear box 1:5 2WD

2-speed gear box, retrofotting is possible for Smartech/Carson C5, all 1:5 2WD FG models except Formula 1 + FG EVO 2020, adjustable shift point, high reliability, gear wheels can be changed in no time. During a competition we recommend to use the small gearwheels with 16-26 teeth in alloy oder steel.If you use the gear wheels (38 teeth) you need the alloy hub A 47mm ().Contained pinions: 22 to 42 teeth and 24 to 40 teeth.Contents:1 piece

€229.50*

7425 FG Plastic gearwheel 39 teeth - 1pce.

Suitable for all 1:5 models.Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€18.90*

7432 FG Steel gearwheel hardened 24 teeth - 1pce.

Item N° 7432 Steel gearwheel hardened 24 teeth - 1pce.Suitable for 39, 40 and 41 teeth main gear wheel.Diameter 38.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€30.50*