7430/25 FG Alloy gearwheel 25 teeth - 1pce.

€13.90*

Available

Product number: fg_7430_25

EAN: 3410569696304

Product information "7430/25 FG Alloy gearwheel 25 teeth - 1pce."

Extreme light alloy gear wheel in anodizing quality with 25 teeth suitable for the gear wheels with 39, 40 and 41 teeth.
Diameter 38,7 mm
Bore 10 mm
Total width 18 mm
Tooth width 11.5 mm
Module m=1.5

Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

7750 FG small module 1,25 transmission set, steel

Small steel modul (1,25) transmission set for Sportsline and Challenge Line, improves performance and reliability.

€99.99*

HT-Alloy pinions for FG and Carson C5 / R5, 1 pce.

zahn_0003 Size: y19418 - 18/46 coated surface

Hard coated surface for wear protection.Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€29.90*

7430/24 FG Alloy gearwheel 24 teeth

Genuine FG spare/option part. Extreme light alloy gear wheel in anodizing quality with 24 teeth.Suitable for the gear wheels with 39, 40 and 41 teeth.Dimensions:Diameter: 38,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11,5 mmModule: m=1,5Contents:1 piece

€30.20*

6494/01 Gear 62 teeth EVO monoblock

€67.50*

HT-Alloy pinion for Attack onroad use y0096, 1 pce.

Hard-coated 25T alloy pinion for use in combination with a . This pinion allows for use of the car on tarmac running touring car tires.Module: m=1,5

€27.90*

y0714 Alloy pinion 19 tooth, hard anodized, for Carson/Smartech 1/6 scale offroad - 1pce.

Item N° y0714 Alloy pinion 19 tooth, hard anodized, for Carson/Smartech 1/6 scale offroad - 1pce.Very low weight hard anodized 19T alloy pinion, for use with the stock 48T spur gear on 1/6 scale 2WD off-road cars from Carson/Smartech/Nutech a.s.o.Diameter 31,6 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€27.90*

7430/23 FG Alloy gearwheel 23 teeth - 1pce.

Extreme light alloy gear wheel in anodizing quality with 23 teeth suitable for the gear wheels with 39, 40 and 41 teeth.Diameter 38,7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€30.20*

Customers also viewed

6433 FG Steel pinion 20 teeth - 1pce.

Item N° 6433 Steel pinion 20 teeth - 1pce.For combination with 44T main spur gear.Diameter 32.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule: m=1,5

€37.00*

7430/24 FG Alloy gearwheel 24 teeth

Genuine FG spare/option part. Extreme light alloy gear wheel in anodizing quality with 24 teeth.Suitable for the gear wheels with 39, 40 and 41 teeth.Dimensions:Diameter: 38,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11,5 mmModule: m=1,5Contents:1 piece

€30.20*

10040 FG Rear axle carrier left - 1pce.

Fits formula 1 cars only.

€25.00*

1000-63 Mecatech conversion kit for using DOT4/DOT5 brake fluid

Genuine Mecatech spare/option part. Replacement part for Mecatech twin piston hydraulic brake.Set with pistons and gaskets/seals, allows for the use of DOT4/DOT5 brake fluid.Contents:1 set

€111.00*

y0557 Zenoah G230RC with Walbro carburetor WT 603B

23 cc Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€264.90*

y1218 Springs for drive shafts

Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

7432/25 FG Steel gearwheel hardened 25 teeth

Suitable for 39, 40 and 41 teeth main gear wheel.Measures:Diameter: 38,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11,5 mmModule: m=1.5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn't really matter.Content:1 piece

€34.50*