67218MI FG STYX tire medium with inserts "yellow"

MadMax MAXI PIN tyres have been specially developed for carpet race tracks!  The special block tread pattern, with 480 knobs per tyre, provides excellent grip, but also puts extreme strain on the tyre and the rim.  To stabilise the tyre, the outside of the tyre shoulder is equipped with vertical ribbing on the side, which minimises tilting under load and counteracts the shear forces that occur in bends. Furthermore, the MAXI PIN tyres have knobs positioned on the side of the outer side, which particularly support the steering behaviour of your RC car in bends. Taken together, the MAXI PIN tyres provide maximum grip.  Dimensions:  Outer diameter: 185 mm  Tyre width at the outer edge of the tread: 75 mm  1 pair

Genuine FG spare/option part. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Contents:2 pieces/1 pair

You can select the tyre hardness above:  - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and  - Hurrax HX400 extreme Grip Soft 175/70 mm tyre  Please select which tyre you prefer.  You also have the option of having the tyres delivered ready glued for an additional charge.  Please click if you want to have the tyres ready glued! HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms

Genuine HT spare/option part. The Maxi-Pin competition tire is particularly suitable for tracks with a hard packed surface, as well as for tracks with a higher percentage of carpeting. The tread is not extended into the tire?s sidewall to reduce the side bite of the Maxi-Pin tire; the car remains controllable on such challenging tracks, which makes this tire a must-have for your "tire box"! Since the Maxi-Pin tire has many fine pins for a high number of biting edges and a low tread depth for reduced flex work, depending on the track?s surfaceincreased tire wear may be expected. For wet conditions the soft compound is recommended, under normal condition the medium compound is usually your best choice. HPI Baja 5 cars can also use these tires when equipped with special adapters. Dimensions:Diameter: 155 mmWidth: 67 mmInner diameter: 106 mmContents:2 pieces

Genuine HPI spare/option part.The Dirt Buster rear Block tyre in S Compound is the perfect all-terrain pattern and compound for the Baja 5B! It fits easily on the multipiece rear wheels and provides the excellent grip and traction needed to roll over any type of surface you might encounter. Dozens of square-shaped pins grab dirt and grass to propel the Baja through all terrains. The low-profile sidewalls resist flex, giving you more traction in turns than a high-profile tyre would. This is the perfect off-road tyre for the Baja!Dimensions:Diameter: 170 mmWidth: 80 mmContent:2 pieces / 1 pair

Original Losi TLR replacement/upgrade part. High-performance race tires pre-glued.Top off-road 1:5 tires designed for RC car racing.Contents: • 4 pieces / 2 pairs • Wheel mounting with 24mm hex • Tire outer diameter: 185mm • Total tire width: 70mm

You can select the tyre hardness above:  - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and  - Hurrax HX400 extreme Grip Soft 175/70 mm tyre HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms

For HPI Baja 5BDimensions: Outer diameter: 170 mm Rear tire width: 80 mmThe Hot Bodies off-road tyre range has expanded to fit the 1/5th scale Baja 5B from HPI!Now available for the Baja buggy are the awesome Double Blade 2WD front tyres, as well as the Proto and Khaos rear tyres!Use HB Baja tyres to put the hurt on the opposition!White compound is medium, great for practice and all-around use.Blue compound is firm for high-bite tracks.

HURRAX extreme Race tire and insert 175x70 mm HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mm HURRAX extreme tires are available in soft (blue marker!) and medium through our shop menu.Contents:2 pieces tires2 pieces inlays

Genuine FG spare/option part. New universal multi off-road pin spike tire equipped with 540 full and 300 hollow pins. This new concept provides more grip, precise control and longer tire life.The new tyre shape also ensures better suspension and optimum response on the track.The tire comes in four rubber compounds:SS Rubber for use at outside temperatures between 0° and 15°S Rubber for use at outside temperatures between 0° and 20°M Rubber for use at outside temperatures between 20° and 35°H Rubber especially for use on carpet and astro turfThis rubber is radically different from other types and also ensures a totally different reaction of the tire on the track.The extremely high grip level and the optimal steering behaviour of the tire set new standards on the track.Without tire inserts!Contents:2 pieces

Genuine FG spare/option part. New universal multi off-road pin spike tire equipped with 540 full and 300 hollow pins. This new concept provides more grip, precise control and longer tire life.The new tyre shape also ensures better suspension and optimum response on the track.The tire comes in four rubber compounds:SS Rubber for use at outside temperatures between 0° and 15°S Rubber for use at outside temperatures between 0° and 20°M Rubber for use at outside temperatures between 20° and 35°H Rubber especially for use on carpet and astro turfThis rubber is radically different from other types and also ensures a totally different reaction of the tire on the track.The extremely high grip level and the optimal steering behaviour of the tire set new standards on the track.Without tire inserts!Contents:2 pieces

Genuine TLR spare/option part.The set includes:1 pair of TLR 45000 genuine Losi 5ive-B rims1 pair of TLR 45002 genuine Losi 5ive-B race tires1 pair of TLR 45003 genuine Losi 5ive-B tire insertsAlso available mounted and glued in the options menu!Contents:1 pair

Genuine HT spare/option part.These heavy duty differential drive cups for front or rear differential in a Losi 5ive-T/B or MINI WRC are made of 300M / Böhler V132 steel and are characterized not only by high hardness, but also simultaneously toughness. The service life is therefore much higher than for the stock cups.300M steel is used in motorsport and aviation for high strength parts. As a highly pure material, it is significantly more expensive than conventional steels, its high basic strength and toughness make the machining a time-consuming task.The shape of these drive cups now allows the use of driveshaft boots and grease lubrication, which increases service life enormously. In addition, these HD drive cups have two sets of slots for the pin of the drive shaft, this means another doubling of the service life.We recommend y0809 Klüber grease for lubrication of closed HD drive cups.A dry run like with stock parts is theoretically possible, but absolutely not recommended because it would waive the enormous advantage of encapsulated lubrication and the associated wear reduction. The set for the rear includes modified stock alloy bearing carriers, which provide improved clearance for the driveshaft boots.You can find advices for installation at the specifications-tab.Contents:Front set:2 pieces of 300M steel HD differential drive cup, front and rear application2 pieces of driveshaft bootsRear set:2 pieces of 300M steel HD differential drive cup, front and rear application1 pair of modified bearing carriers2 pieces of driveshaft boots

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder is also available with completely installed remote control. Just fuel up, start the engine and drive off.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm