For technical reasons we had to modify the square wheel adapter of the new Off-Road wheel 2011. Therefore it is necessary to mount the 12mm alum. square wheel driver (ItemN°. 06107/07) for this wheel. After the assembly of this square wheel driver it is possible to drive also GRP or Hörmann wheels without any further modifications. We have marked the Off-Road wheel 2011 on the inside with the number 1.
Item N° 67210/05 Mini Pin M / OR tires, Leo wheel white, glued, 2pcs. Completely new revised and in important details improved Mini Pin Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Pin tires are especially well-suited for hard and rough ground. They give the model a lot of traction, driving stability and grip in curves. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle.The tires are ready glued on the new Leo wheels. For the assembly you need the 12mm square wheel drivers (Item-no.: FG 6107/07). The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Item N° 67214/06 Mini block H / OR tires, glued, white, 2pcs.Completely new revised and in important details improved Mini Block Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Block tires are especially well-suited for slightly loose and humid ground. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. The Mini Block tires are also well-suited as front tires for 2WD models in combination with the Mini Pin tires on the rear axle. The tires are ready glued on the new Leo 1:6 wheels. For the assembly you need the 12mm square wheel drivers (ItemN°. 06107/07).Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The glued tires are not suitable for the FG models Marder, Beetle, Off-Road Buggy and Monster models.
Item N° 67210/02 Mini Pin M/ OR tires, with inserts, 2 pcs.Completely new revised and in important details improved Mini Pin Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Pin tires are especially well-suited for hard and rough ground. They give the model a lot of traction, driving stability and grip in curves. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. These tires fit all 1:6 scale wheels with Ø110mm and a width of approx. 64mm. Suitable inserts are enclosed.
Item N° 67210/01 Mini Pin S/ OR tires, with inserts, 2 pcs.Completely new revised and in important details improved Mini Pin Off-Road tires. The rubber material is more wear resisting, grip and traction were improved and the tire wall was reinforced to prevent a tearing of the rubber. The tire inserts are now stronger and therefore more wear resistant. The FG Mini Pin tires are especially well-suited for hard and rough ground. They give the model a lot of traction, driving stability and grip in curves. We recommend the M and S version in the front and the rear. The H version with slightly less grip can be used for the front axle. These tires fit all 1:6 scale wheels with Ø110mm and a width of approx. 64mm. Suitable inserts are enclosed.
Genuine FG spare/option part.With a Ø of 185mm extremely large and 85mm wide OR Truggy tire. A lot of grip, therefore high curve speeds on almost every surfaces possible. Available in different hardnesses. Suitable for all FG Buggy and Monster models. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
The Mecatech FW01 is for sure the currently most innovative 1/5 race car designed for the dedicated and technically enthusiastic rc car driver.Everyone is enthusiastic about the perfectly fitting and precise workmanship at the highest level. Only high quality materials are used for the production.Since many years Mecatech is a well-know premium manufacturer of largescale hydraulic brakes or shocks and, as only a few may know, a technology expert for a number of Formula 1 racing teams!The Performance Kit from the FW01 is particularly intended for "racer" and differs from the Chassis Kit model by the Performance Kit. Here the list of parts are not including:DifferentialEngine Clutch, Airbox and tuned pipe systembody shell and tiresElectonic components such as servos, batteries and Remote controlPerformance Kit:engine brace left and rightfront stabilizer bar 2.75 mm titanium ready for installationrear stabilizer bar 1.75 mm titanium ready for installationthe two 80 gram front weightsthe two smaller 80 gram center weightsWith the Performance Kit the vehicle is quasi equipped as used at races!Stock gearing:Clutch pinion / spur gear: 36T / 64TLayshaft pinion / differential: 24T / 73TCurrently the Mecatech FW01 is for sure the benchmark of the 1/5 scale racing scene! In the first year Markus Feldmann won with his FW01 1: 5 Mecatech on one of the world's finest and most demanding race track in Lostallo / SwitzerlandMecatech is multiple German, European and World Champion with the FW01 and as the last result:Markus Feldman wins the European Championship in Tourlaville/France. All top 5 positions went to drivers running a Mecatech FW01. 7 out of 10 finalists cars were Mecatech FW01.Although the fit of the Mecatech FW01 parts makes the assembly of the car a great experience, some of our customers want to use the expertise of our shop and wish their FW01 fully assembled and tuned in by us! The complete assembly of your FW01 by our workshop is possible for an additional charge. Please note that the costs of the full assembly with servos a.s.o. do not include the price of any rc-components. If you do not have a suitable radio system with servos and batteries as well as switch and charger, you have to take an additional EUR 800 to EUR 1,500 for this equipment into account. We will be happy to make you an appropriate offer. We are currently waiting for the latest version of the Mecatech FW01. We are currently waiting for the latest version of the Mecatech FW01.Included in the chassis kit:- All pinions- clutch bell- Coupling fixation- All parts and screws for mounting the enginenot included:- differential- Engine and linkage- body shell and spoilers- Airbox- clutch - engine- Electronics- TiresWe are currently waiting for the latest version of the Mecatech FW01.
€2,999.00*
This website uses cookies to ensure the best experience possible. More information...