HT-Steel pinions for Carson / Smartech 2WD offroad cars
€29.90
Product information "HT-Steel pinions for Carson / Smartech 2WD offroad cars"
The pinions are made from nitrited steel. The do all correspond with the standard main gear and are secured using two grubscrews.
These pinions are profile regraded and have all the same diameter!
Module: m=1,5
Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.
Contents:
- 1 piece
Login
Customers also viewed
Genuine FG spare/option part.Gear plate with metal brake plates and big Epoxy brake disk, therefore higher braking power with less heat development. Measures:Bearing seats clutch bell: 22 mm x 6 mm Bearing seat layshaft: 19 mm x 7 mm Content as shown.Contents:1 set
Genuine HT spare/option part.Coarse pitch spur gear for the differential, especially for use in off-road and monster models. The teeth are stronger and , due to their bigger size, a little bit more forgiving when the gear mesh is not adjusted correctly.Fits FG cars and Smartech / Carson 2WD cars.Only for use with the extreme duty pinions! Not for use in combination with Elcon rear drivetrain unit or Elcon differential!Module: m=1,75.Contents:1 piece [INCLUDE]profilverschoben[ENDINCLUDE]
Item N° 32462 Wheel drives steel - 18 mm square - 9,5 mm wide - 2pcs.18 mm square steel wheel drives, 9,5 mm wide, 0.5 mm land for running against the the wheel bearing's inner race.Two threads for M5 grub screws with 90° offset, 8 mm bore diameter for wheel shaft.Black-finished surface.
Genuine Carson spare/option part. Painted body shell set for the Dirt Attack GP 3.0.Contents:1 set
This carriers makes it possible to run steel spur gears on the layshaft. Pebbles heat and the high torque of monster truck applications are no longer a problem.The carrier is designed for reverse installation as seen on the FG EVO car, where the hubs of the pinion and the spur gear carrier are pointing to the outside of the car. The carrier features M8 (eight, no typo) grub screws for installation on the layshaft. This means that the tip of the screw is as wide as the flat area on the shaft and ensures best possible load distribution.
Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)Pinions up to 16T can be used on the layshaft as well.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Teeth:Item no.:13 Teeth HT y026814 Teeth FG 604614 to 48 Teeth HT y011615 to 48 Teeth FG 604715 to 48 Teeth HT y19354 wide16 to 48 Teeth FG 643116 to 48 Teeth FG 6431/1 wide17 to 48 Teeth HT y19355-116 to 46 Teeth HT y011917 to 46 Teeth HT y1935518 to 46 Teeth FG 643219 to 46 Teeth HT y1935718 to 44 Teeth HT y012319 to 44 Teeth FG 6432/220 to 44 Teeth FG 643321 to 44 Teeth HT y1935820 to 42 Teeth HT y090421 to 42 Teeth FG 7431/2122 to 42 Teeth FG 743121 to 40 Teeth FG 7432/2122 to 40 Teeth FG 7432/2223 to 40 Teeth FG 7432/2324 to 40 Teeth FG 743225 to 40 Teeth FG 7432/2526 to 40 Teeth HT y1936426 to 38 Teeth FG 7433Contents:1 piece
Suitable for Zenoah ZG22, G230RC, G230RC 04, G260RC, G240, G270, G290, FG CY23 and CY26.With cutout for all FG models.