4820/32 Samba Competition tuned pipe for Losi 5ive-T/ 2.0 until 32 cm³

The Samba 5ive T tuned pipe from the 1/5 world champion!At the 1/5 World Championship were place 1 to 10 (!) equipped with a samba tuned pipe system.A proof of competence without equal!BiG BELLY, special version for the 5ive-T / Monster Truck XL with engines up to 32 cm³ engine. Comes with complete hardware for installation.Top quality and optimized performance across the entire rpm range of your engine.

The Samba 5ive T tuned pipe from the 1/5 world champion!At the 1/5 World Championship were place 1 to 10 (!) equipped with a samba tuned pipe system.A proof of competence without equal!BiG BELLY, special version for the 5ive-T / Monster Truck XL with engines up to 32 cm³ engine. Comes with complete hardware for installation.Top quality and optimized performance across the entire rpm range of your engine.

Genuine Mielke spare/option part.The tuned pipe system from premium manufacturer M. Mielke was specifically designed for Losi DBXL 2.0 in combination with large displacement and modified engines.The elaborate, angled design, makes best use of the available space in the DBXL 2.0 allowing for optimum performance! When designing the system, it was especially important to maximize the distance to the battery box of the DBXL 2.0 in order to minimize the thermal load on the battery. At the same time, the large distance improves access to Box. Contents:1 set

Genuine Samba spare/option part.O-ring dimensions:20 x 1.5 mmContent:2 pieces

Item N° 7112O-ring for Racing fixing kit, 4 pce.Replacement o-ring for Samba order number: 7110, Installation kit for 50 mm pipes, set Thickness: 2,5 mmDiameter: 45 mm

The new TT0900 electric starter is pre-assembled and fits a wide range of models including the Losi 5ive-T, 5ive Mini and DBXL, most FG models, HPI-Baja / Wild Attack series etc. The TT0900 electric starter can be started with the remote control (free channel required!). The new TT0900electric starter has much more power than the previous Electric starter thanks to the brushless motor and higher voltage. The popular Zenoah G320 is no longer a problem. It also no longer uses a one-way bearing, which clearly increases reliability. Also the installation space has been noticeably reduced by the motor and a planetary gearbox.The starter components to be fitted weigh about 666 grams plus the battery.For mounting the starter, the flywheel on the engine is replaced by the version with spring-loaded pawls included in the delivery. The tools required for this, piston stopper and flywheel puller, are also included in the delivery.For the 3rd channel the transmitter should have a switch with two positions (momentary switch preferred) or a controller. An additional channel is required for a remote engine killswitch. A killswitch is included in the scope of delivery, but a real fail-safe module such as TT0990 offers higher safety. A possibly already existing failsafe module can also be used.Due to the splitting of the functions engine start and engine stop on two channels, no more compatibility problems with different remote controls are to be expected, only the availability of free channels matters.A 3S LiPo battery is required as the power source.In the shops options menu, we offer a special battery with a more compact design (5,600 mAh/30C, 110 x 49 x 34 mm) which makes installation usually easier in many cars, as well as a battery with standard dimensions (3,900 mAh/60C, 135 x 45 x 25 mm). Of course, other 3S batteries can also be used at your own discretion, but the load capacity (capacity x C-rate) should be on a similar or higher level.Please note that we cannot ship batteries to countries outside the European Union!Since the starter unit can be mounted vertically or horizontally and the brushless starter motor is very small, almost all air filters and most tuned pipe systems can be used.Notes regarding necessary modifications known to us for mounting the starter depending on the vehicle: FG 4wd onroad Rear r/h plastic body mount, depending on position, slightly modified or relocated FG 2wd onroad horizontal engine No modifications Mecatech FW01 No modifications FG 4wd Buggy sportsline Depending on the body shell, minor trimming is required. FG 2wd Buggy current chassis Depending on the body shell, minor trimming is required. FG 2wd Marder (old chassis) Starter fits without modifications to the chassis plate. However, the body shell has to be cut out a bit more seriously in the area of the starter. A repositioning of the rear r/h body mount is recommended. FG Monster Cut the r/h side panel slightly and add a flat area to the aluminum tube which supports the panel on the engine Losi 5ive-B Depending on the tuned pipe, mount starter with motor on top or on the l/h side. Losi 5ive-B Mount the starter motor on the l/h side, space for the tuned pipe is very tight and must be tested in each individual case. No problems when using the stock muffler box. Losi DBXL Depending on the tuned pipe, mount starter with motor on top or on the l/h side. If the starter motor is to be mounted on the side, one screw of the motor roll cage must be replaced by a CSH screw. Carson C5 Only with Zenoah or CY engine, not with Smartech PT engine (different hole pattern on engine)! Carson C6 With the C6, depending on the body shell, trimming is required. HPI 5B/T Depending on the body shell, minor trimming is required. Carson Wild GP Attack Depending on the body shell, minor trimming is required. The accommodation of the engine killswitch, controller unit and wiring harness must be carried out at your own discretion. User Manual FG 4WD On-Road FG Monster FG 2WD On-Road horizontal engine FG 2WD/4WD Buggy current chassis Losi 5ive-T Losi DBXL FG 2WD Marder (old chassis)

With our 12S Beast Edition you can choose between 2 variants:1.  Hobbywing Ezrun Max5 HV ESC 250A up to 12S LiPo BEC8 and Ezrun 650KV 4pol brushless motor, without surcharge.2.  Hobbywing Ezrun Max4 HV ESC Sensorless 300A up to 12S LiPo, BEC 10A and Top Tuning Beast Brushless Motor 620KV 4pol, 190,00 € extra charge.                 When the original 5IVE-T was introduced the world of 1/5-scale off-road racing changed, and this iconic platform became one of the most successful and influential platforms to date. Now get ready for 2.0! The Losi 5IVE-T 2.0 BND: 1/5 4WD Gas Short Course Truck has all of the unrivaled performance of its predecessor and includes Bind-N-Drive technology, allowing you to pick the transmitter that best fits your lifestyle. Comes with y1549/01 ZTW Beast Pro 300A 12S ESC and 520KV brushless motor and TT1021 Top Tuning Electric conversion kit for the ZTW BEAST version included.The revised chassis layout reduces the front drive shaft angle for improved durability and increased 4WD balance. Plus, the new rack style bellcrank steering assembly makes for easy Ackermann changes and overall improved steering geometry. Additional advances include an updated front hood, and hard anodized bleeder caps and shock bodies for improved shock performance. All this ensures the 5IVE-T 2.0 continues to reign supreme.Key Features Without surcharge : Ezrun MAX5 HV G2 ESC 12S and Ezrun 650KV brushless engine. Surcharge 190€ : Ezrun MAX4 HV G2 ESC and Top Tuning BEAST 620KV Brushless engine. Innovative Bind-N-DriveSpektrum 6200A DSMR 6-Ch AVC Telemetrie receiverImproved bar style steering rack with adjustable AckermannImproved center differential orientationImproved drive line angleHeavy-duty brakesTough steering and gas/throttle servo braceExtra-large 800cc capacity fuel tank What's in the Box?Losi 5IVE-T® 2.0 BND 4WD SCTSpektrum 6200A DSMR 6-Ch AVC Telemetrie receiverS900S 1/5 Scale Metal Gear Steering ServoWheel WrenchRod End/Shock End toolMulti WrenchSpark Plug WrenchBind Plug2.0mm, 2.5mm, 3.0mm, 4.0mm Allen WrenchesProduct ManualEC8 plug connection for optimum power transmission18 teeth pinionSpecification:Continuous Current: 250/300A ESC EzrunWaterproof: spash protectedBrushless Motor 650/620 kV Driving batteries with the following maximum dimensions can be installed: Length: 165 mm Width: 51 mm Height: variable The speed controller (ESC) requires EC8 connections or corresponding ! Contents:1 piece If you run the maximum operating voltage approved for an esc, there is a risk, especially in large scale cars, that under certain circumstances the reverse currents generated by the motor when braking will destroy the esc.For this reason, we recommend using a mechanical brake (as with gas powered vehicles) and deactivating the brake in the esc programming.Please note that reversing is then no longer possible!