y68401/01 Rear lower alloy wishbones small, set
Product number:
y68401_01
EAN:
4058575032281
Product information "y68401/01 Rear lower alloy wishbones small, set"
Rear lower alloy wishbones salon cars, set
Set contents small rear lower wishbones, alloy ball-and- socket joints, hardened wishbone pins, small parts, screws.
Suitable for 4WD Mini Cooper and for FG 2WD Touringcar like the Sportsline or the Ecoline too. Or suitable for all 1:5 models with a width up to 400mm.
Set contents small rear lower wishbones, alloy ball-and- socket joints, hardened wishbone pins, small parts, screws.
Suitable for 4WD Mini Cooper and for FG 2WD Touringcar like the Sportsline or the Ecoline too. Or suitable for all 1:5 models with a width up to 400mm.
Login
Similar products
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Wheelie bar with double ball raced wheel, cnc-machined from high strength alloy. The arm has a rubber suspension unit, the height is infinitely adjustable. The suspension allows for a maximum deflection of 30 degrees and is dirt- and mud-proof. The wheel bearings are sealed.The unit fits FG Monster Truck, Monster Beetle and Marder BigFoot, except for Monster Buggy Off-Road WB535 4WD. Installation on other models will be possible, but requires modifications to the chassis, mainly to accept the bolt pattern. The Carson Attack already has the correct pattern.
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces
Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces
Genuine FG spare/option part. The set will shipped without gear carrier plate. Contents:1 set
Genuine FG spare/option part. Please note: If you own a Leopard 2WD with the old 130.5 mm driveshafts (same part number), the upgrade of both shafts is recommended.Contents:1 piece
Genuine HT spare/option part. Dimensions:Total length: approx. 132 mmLength center pin / center pin: approx. 123 mmShaft diameter: approx. 6 mmBall diameter: approx. 9,8 mmPlease note:If you own a Leopard 2WD with the old 130.5 mm driveshafts, the swap of both shafts is recommended.Contents:1 piece
For the secure installation of driveshaft boots.
Customers also viewed
Genuine GPM spare/option part. High quality cnc machined parts made by GPM Racing Products from high strength billet aluminum. Fits all vehicles from the HPI Baja 5 line and Carson Wild GP Attach.Contents:1 piece
The Wheelbase of the WB535 2WD version is 60 mm longer. This modification improved the directionally stability as well as further driving qualities significantly. In addition parts of the 4WD Monster models were assembled in order to make a conversion to a 4WD model possible with low efforts. According to the large tires this model can be driven almost everywhere. The 26 cm³ Zenoah engine provides sufficient power. Driving fun as well as tremendous looks are the prime characteristics of these models.The body shell comes unpainted, a decal set with writings for further decoration is enclosed in the delivery.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical description:The undercarriage of the Monster models is built on a 4 mm angled alloy plate. All borings for fixa- tion of the chassis parts at the bottom side are countersunk in order to prevent the screw heads from sticking out. At the front axle you have the possibility to adjust toe-in or toe-out as well as the wheel camber through track rods with right-hand/left-hand thread. The wheel camber of the rear wheels can be adjusted individually through adjusting screws with right-hand/left-hand thread. Four large-volume oil-pressure shock absorbers are mounted at the lower double wishbones of front and rear axle, these are able to absorb larger shocks of jumps to a great extent and care for an optimal road grip. All rotating drive components are supported by ball bearings. Highly stressed steel parts such as rear gearwheels, differential gears and drive components are hardened. Fuel tank and ra- dio control parts are protected through alloy plates at the sides. The body parts are made of coloured or respectively clear polycarbonate. The Monster tires with tire inserts are glued on chrome-plated rims.The models are equipped with a powerful 26 cm³ combustion engine with ready-for-use oiled air fil- ter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURAlloy spur gear carrierUse for 48T - 46 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 15The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 217,30 EURThe pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.The RTR version is delivered with assembled and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control sys- tems are suitable.Dimensions: Length: 780 mm Width: 510 mm Height: 350 mm Wheelbase: 353 mm
