y19013 K&N Air filter oil

rc-car-online

€16.11*

% €17.90* (10% saved)

Content: 204 Milliliter (€78.97* / 1000 Milliliter)

Prices incl. VAT plus shipping costs

Available

Product number: oel_0006

EAN: 024844113023

Product information "y19013 K&N Air filter oil"

Genuine K&N spare/option part.

The K+N air filter oil is only suitable for all K+N air filters, foam preliminary filters and filter inserts.

Content:

1 piece / 204 ml

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

y1013 Motul Air filter oil for foam filters

Genuine Motul spare/option part. High-cling oil for foam cartridge air filters, especially for offroad and street use. The oil reinforces the the air filter'e efficiency and retains dirt, mud and sand particles, which will greatly extend the life of the engine. The blue tint makes it easier to control even oil application to the filter.Apply oil to filter generously and work the foam vigorously by hand to ensure complete oil penetration. Press foam slightly to remove excessive oil when done.Contents:1 piece / 400 ml

Content: 400 Milliliter (€47.25* / 1000 Milliliter)

€18.90*

y0284 Air filter oil for foam filters, 50 ml

This air filter oil is designed for lubricating foam filters for on-road and off-road use. It reinforces the filters' efficiency for better carburation and retains dirt, mud and sand particles. Prevents water from penetrating into the filter.It is recommended to put the filter with a little bit oil in a small polybag and work it vigorously by hand. Excessive oil must be pressed out (don't wring the foam!) afterwards.For cleaning the filter please use the special foam cleaner y0523.The filter element must be dry before re-oiling.Content:50 ml

Content: 50 Milliliter (€119.00* / 1000 Milliliter)

€5.95*

6441 FG Filter oil for foam filter 50ml

Genuine FG spare/option part. For use with all foam filters, not for fabric filters.Content1 piece

Content: 50 Milliliter (€190.00* / 1000 Milliliter)

€9.50*

Z759 HPI Set Screw 4-40x1/8 3mm

Contents:4 pieces

€4.99*

Customers also viewed

6516 FG Air filter oil spray 192 ml

Genuine FG spare/option part. The K+N air filter oil is only suitable for all K+N air filters, foam preliminary filters and filter inserts.Content:1 piece / 204 ml

Content: 204 Milliliter (€87.75* / 1000 Milliliter)

€17.90*

6441 FG Filter oil for foam filter 50ml

Genuine FG spare/option part. For use with all foam filters, not for fabric filters.Content1 piece

Content: 50 Milliliter (€190.00* / 1000 Milliliter)

€9.50*

Servosaver Blocker - y1039

Servosaver blocking pin to block the servosaver in a middle position for a accurately setup of the front suspension.Fits on FG EVO Touring Cars 06, 07, 08 and Competition 07.

€11.90*

50353021 Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pcs.

Item N° 50353021Support Blocks for the Lightscale Droop Gauge 35 mm rear, 1 pce.This is an Alloy Support Block anodized in black colour with 35mm height.The Support Block is manufactured as a rectangle and so can used as a 30mm as well as a 35mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.

€29.90*